JVC D-ILA - Manual

The Rogers Report

1080p D-ILA

®

Front Projector

Breaking Barriers Again

The new JVC

®

DLA-RS2U 1080p D-ILA

®

video projector shat-

ters the industry-leading contrast standard set by its predeces-
sor, the DLA-RS1U. The RS1 (as it is known to home theatre
enthusiasts) astonished everyone a year ago by achieving a
native full-field contrast ratio of 15,000:1. The contrast ratio
specification for the RS2 has been doubled to 30,000:1, and my
review unit met that stellar performance mark, while still produc-
ing excellent brightness.

The RS2 also adds other features and image-quality

improvements, including remote control of lens focus and zoom,
a vertical stretch mode for an external anamorphic lens, and
advanced gamma adjustments.

Technology

The RS2 incorporates upgraded 0.7-inch, 16:9 D-ILA (Direct-

drive Image Light Amplifier) panels with enhanced wire-grid
polarizers. D-ILA is a vertically aligned Liquid Crystal on Silicon
(LCoS) technology. The projector has three D-ILA panels, each
with the same 1920 x 1080 pixel resolution as 1080i and 1080p
high-definition video formats. The D-ILA devices are said to
have a native contrast ratio of 40,000:1.

The projector utilizes a 200-watt UHP (ultra high-pressure)

mercury projection lamp. The light from the projection lamp is
split into red, green, and blue beams that each reflects off one
of the D-ILA panels. The brightness of each pixel is controlled
by varying the polarization of the light as it passes through the
liquid crystal layer of the panels. The reflected red, green, and
blue light is directed through a single lens to create a full-color
image on the screen. The three-panel design eliminates the
need for a color wheel and the potential rainbow color separa-
tion artifacts of single-chip DLP projectors.

Appearance

The RS2 has the same attractive glossy piano-black case as

the RS1. The front bezel is flat black, and a matching accent

strip runs the length of

the projector in the center of

the top cover. The zoom lens is

centered in the middle of the front bezel,

which has a cool air inlet on one end of the bezel

and a hot air exhaust vent on the other. All video inputs are

on a recessed rear panel, with a power cord socket below them. The
lamp cover is located on the side of the projector, which makes it
easy to replace the lamp when required. There are small and unob-
trusive Warning, Lamp, and Power indicators on the top cover, in
addition to several control and menu navigation buttons.

Set Up

The RS2 projection lens now has remotely controlled zoom and

focus adjustments, replacing the manual adjustments of the RS1.
With a 100-inch diagonal (87.2- x 49-inch) 16:9 (1.78:1) screen, the
2.0x zoom lens provides a throw distance between 9.88 and 19.95
feet. Optimum focus is essential to achieve the best performance
from this projector, and that is now easier to adjust while standing at
the screen, thanks to the remote-controlled lens. However, the focus
can only be adjusted while viewing a built-in green crosshatch test
pattern. It would be better if the user could view his or her own test
patterns and other images while focusing.

The projector can be adjusted for up to 80 percent vertical and

34 percent horizontal lens shift. That means the center of the lens
can be 30 percent of the screen height above or below the screen,
and 34 percent of the screen width to the right or left of screen cen-
ter. The lens is manually shifted horizontally and vertically by two
adjustment knobs located on the bottom edge of the front bezel. The
all-mechanical system feels a bit imprecise, but with a little fiddling
the image can be positioned as desired. The maximum vertical and
horizontal shifts can’t be applied simultaneously. But since the lens
shifts slightly increase chromatic aberration, having both at maximum
wouldn’t be a good idea anyway. I recommend keeping the horizon-
tal lens shift near the minimum and limiting the vertical lens shift to
the top or bottom of the screen when possible.

Connections

The rear-panel connections are rather limited. There are two HDMI

inputs, a YPbPr/RGsB component input (three RCA connectors), an
S-video input (four-pin mini-DIN), and a composite video input (RCA
connector). The analog RGsB input is compatible with three-wire
RGB signals that have sync-on-green, but there is no provision for
analog RGBHV signals. There is also an RS-232 port for control, but
there are no screen trigger outputs. The RS-232 syntax is included in
the user manual.

Greg Rogers

JVC

®

DLA-RS2U

Widescreen Review • Issue 129 • March 2008

2

1/7

#129 JVC REPRINT:Layout 1 2/7/08 1:54 PM Page 2