Jonsered CC2036 - Manual

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole. CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure ha...

GENERAL SAFETY PRECAUTIONS English – 9 saw. Certain harnesses also have a quick release fitted to the support hook. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly. Muffler The muffler is de...

GENERAL SAFETY PRECAUTIONS 10 – English should operate the socket spanner when loosening or tightening the nut. The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has b...

GENERAL SAFETY PRECAUTIONS English – 11 Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced. Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters using a ...

GENERAL SAFETY PRECAUTIONS 12 – English Trimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting att...

ASSEMBLY English – 13 Fitting the handlebar • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. • Refit the screw in the hole in the rear ...

ASSEMBLY 14 – English Fitting blades and trimmer heads Fitting a blade guard, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Ensure that the guard extension is removed. Use the recommended blade guard. See th...

ASSEMBLY 16 – English Fitting other guards and cutting attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holde...

ASSEMBLY English – 17 Correct height 1 Forestry clearing Adjust the support strap so that the support hook is around 10 cm below your hip. The blade should be angled forward a little. 2 Grass clearing The support hook should hang around 20 cm below your hip so that the blade is parallel to the groun...

FUEL HANDLING 18 – English Fuel safety Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. U...

FUEL HANDLING English – 19 Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the f...

STARTING AND STOPPING 20 – English Check before starting For safety reasons follow these recommendations! • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at th...

STARTING AND STOPPING English – 21 Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the...

WORKING TECHNIQUES 22 – English General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

WORKING TECHNIQUES English – 23 The ABC of clearing • Always use the correct equipment. • Make sure the equipment is well adjusted. • Follow the safety precautions. • Organise your work carefully. • Always use full throttle when starting to cut with the blade. • Always use sharp blades. • Avoid ston...

WORKING TECHNIQUES 24 – English conditions, so that cleared stems fall in the cleared area of the stand. Forestry clearing using a saw blade • The risk of blade thrust increases with increasing stem size. You should therefore avoid cutting with the area of the blade between 12 o’clock and 3 o’clock....

WORKING TECHNIQUES English – 25 Brush cutting with a saw blade • Thin stems and brush are mown down. Work with a sawing movement, swinging sideways. • Try to cut several stems in a single sawing movement. • With groups of hardwood stems, first clear around the group. Start by cutting the stems high ...

MAINTENANCE English – 27 Carburetor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaust ...

MAINTENANCE 28 – English Low speed jet L Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CAUTION! If the cutting attachment rotates when the e...

MAINTENANCE English – 29 this screw (4 mm Allen screw) to increase or decrease the start throttle speed. Proceed as follows: 1 Run the machine at idle. 2 Press the start throttle lock as described under the heading Starting and stopping. 3 If the start throttle speed is too low (below 4000 rpm), tur...

MAINTENANCE 30 – English Bevel gear The bevel gear is filled with the right amount of grease at the factory. However, before using the machine you should check that the bevel gear is filled 3/4 full with grease. Use JONSERED special grease. The grease in the bevel gear does not normally need to be c...

English – 31 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

32 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

FEDERAL EMISSION CONTROL WARRANTY STATEMENT 34 – English YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada...

FEDERAL EMISSION CONTROL WARRANTY STATEMENT English – 35 EMISSION CONTROL WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up to maintenance schedule. 4 Ignition System 1Spark Plug, covered up to maintenance ...

1 Poly Trim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10

Tap n’ Go 35 Spin "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm

"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm Tap n’Go 45 Spin

1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII