Jonsered CS 2137 - Manual - manualsarea.com

Page 2 - IDENTIFICATION OF SYMBOLS

2 IDENTIFICATION (WHAT IS WHAT?) Chain Adjustment Tool (Bar Tool) Primer Bulb Fuel Mix Fill Cap StarterHousing Bar Oil Fill Cap Chain Front Hand Guard Front Handle Starter Rope ON/STOPSwitch Muffler Idle Speed Screw BumperSpike Guide Bar Chain Brake Nuts Cylinder Cover ThrottleLockout RearHandle Thr...

Page 3 - SAFETY RULES; WARNING; PLAN AHEAD; Jonsered; HANDLE FUEL WITH CAUTION

3 SAFETY RULES WARNING : Always disconnect spark plug wire and place wire where it can-not contact spark plug to prevent accidentalstarting when setting up, transporting, ad-justing or making repairs except carburetoradjustments.Because a chain saw is a high-speed wood-cutting tool, special safety p...

Page 4 - KICKBACK; : Avoid kickback which; Do not cut more than one log at a time.; REDUCE THE CHANCE OF; Cut one log at a time.; MAINTAIN CONTROL

4 S Mix and pour fuel in an outdoor area on bareground; store fuel in a cool, dry, well venti-lated place; and use an approved, markedcontainer for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel-ing site before starting engine. S Turn the...

Page 5 - KICKBACK SAFETY FEATURES; : The following features; CHAIN BRAKE

5 Thumb on underside of handlebar Elbow locked S Keep a good, firm grip on the saw with bothhands when the engine is running anddon’t let go. A firm grip will help you reducekickback and maintain control of the saw.Keep the fingers of your left hand encir-cling and your left thumb under the fronthan...

Page 6 - SAFETY; ASSEMBLY; ATTACHING THE BUMPER SPIKE; Mount the Bar

6 SAFETY NOTICE: Exposure to vibrations through prolonged use of gasolinepowered hand tools could cause bloodvessel or nerve damage in the fingers,hands, and joints of people prone tocirculation disorders or abnormal swellings.Prolonged use in cold weather has beenlinked to blood vessel damage in ot...

Page 7 - Place chain onto the sprocket; CHAIN TENSION (Including units; : If the saw is operated; : Muffler is very hot during; OPERATING YOUR UNIT; : Be sure to read the fuel; Oil Cap; : Remove fuel cap slowly

7 Place chain onto the sprocket 7. Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. 8. Fit bottom of drive links between the teeth in the sprocket in the nose of theguide bar. 9. Fit chain drive links into bar groove.10. Pull guide bar forward until chain is s...

Page 8 - Hold saw firmly while pulling starter rope; IMPORTANT POINTS TO REMEMBER; STARTING A COLD ENGINE (or a; IGNITION SWITCH; ON; OFF FULL; STARTING A WARM ENGINE; : If the brake band is worn

8 will cause engine damage. When mixing fuelfollow the instructions printed on the container.Always read and follow the safety rules relatingto fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels(called gasohol or using ethanol or methanol)can attract moisture wh...

Page 9 - Braking function control; CUTTING METHODS; IMPORTANT POINTS; : Do not cut near buildings; Direction of Fall; FELLING LARGE TREES

9 S The inertia activated chain brake is acti-vated if the front hand guard is pushed for-ward, either manually or by centrifugalforce. S If the brake is already activated, it is disen-gaged by pulling the front hand guard backtoward the front handle as far as possible. S When cutting with the saw, ...

Page 10 - of the diameter; NOTE; : Do not stand on the log; Cut only one log at a time.; : If saw becomes pinched; Overcutting; : Never turn saw upside; Overcut through

10 NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of thenotch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut-ting the bottom of the notch. See illustra-tion. Once the notch is cut remove thenotch of wood from the tree. Notch First cut Second cu...

Page 11 - : Be alert for and guard; : Never climb into a tree to; : Limit pruning to limbs

11 S Roll the log over and finish with a secondovercut. S Give special attention to logs under strainto prevent the saw from pinching. Makethe first cut on the pressure side to relievethe stress on the log. BUCKING USING A LOG OR SUP- PORT STAND S Remember your first cut is always on thepressure sid...

Page 12 - SERVICE AND ADJUSTMENTS; : Disconnect the spark; AIR FILTER

12 SERVICE AND ADJUSTMENTS WARNING : Disconnect the spark plug before performing maintenance, exceptfor carburetor adjustments.We recommend all service and adjustmentsnot listed in this manual be performed by anAuthorized Service Dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level Before each use...

Page 13 - : The chain will be moving; STORAGE; : Stop engine and allow to; CAUTION; : It is important to prevent; TROUBLE

13 CHAIN SHARPENING Chain sharpening is a complicated task thatrequires special tools. We recommend thatyou refer chain sharpening to a professionalchain sharpener. CARBURETOR ADJUSTMENTS WARNING : The chain will be moving during most of this procedure. Wear your pro-tective equipment and observe al...

Page 14 - EU Declaration of Conformity relating to 2000/14/EC; DECLARATION OF CONFORMITY

14 DECLARATION OF CONFORMITY relating to 2000/14/EC EU Declaration of Conformity relating to 2000/14/EC We, Poulan/W eed Eater Division, Electrolux Home Products, Inc., Texarkana, TX,75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Jonseredmodel CS2137 chain saw was ass...

Page 15 - TECHNICAL DATA SHEET; BAR; YEAR OF CONSTRUCTION:

15 TECHNICAL DATA SHEET EngineCylinder volume, cm 3 42 Stroke, mm 32 Idle speed, rpm 3,000 Recommended max.speed, unloaded, rpm 13,000 Power, kW 1,8 Ignition systemManufacturer RE Phelon Type of ignition system CD Spark plug Champion Electrode gap, mm 0,5 Fuel and lubrication systemManufacturer Walb...

Jonsered CS 2137 - Manual

Table of Contents:

Summary

Other Jonsered Models