Jonsered BC 2125 - Manual

English – 5 WHA T IS WHA T? What is what? 27 4 26 28 J O N S E R E D S E R V I C E 17 19 18 22 21 20 25 23 24 30 31 4 21 1 Blade 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop switch 9 Throttle lockout 10 Support eyes for harness...

6 – English SAFETY INSTR UCTIONS Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use ...

English – 7 SAFETY INSTR UCTIONS CLO THING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a f...

8 – English SAFETY INSTR UCTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the g...

English – 9 SAFETY INSTRUCTIONS Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked screen will cause the engine to overhea...

10 – English SAFETY INSTRUCTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting performance. • Extend the life of cutting equipment. Cutting equipment Saw blades are intended for cutt...

English – 11 SAFETY INSTRUCTIONS Sharpening the saw blade • See the cutting attachment packaging for correct sharpening instructions. A correctly sharpened blade is essential for working efficiently and to avoid unnecessary wear to the blade and clearing saw. • Make sure that the blade is well suppo...

12 – English ASSEMBLY Assembling the handlebar and throttle • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. • Refit the screw in the h...

English – 13 ASSEMBLY Transport position, handlebar • The handlebar can easily be turned to fit along the shaft for easier transportation and storage. • Loosen the knob. Turn the handlebar clockwise so that the throttle handle rests against the engine. • Now twist the handlebar around the shaft. Tig...

English – 15 ASSEMBLY • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. • To dismantle, follow the instructions in the reverse order. Fitting other guards and cutting attachments • Fit...

16 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. U...

English – 17 FUEL HANDLING Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the f...

18 – English STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

English – 19 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electri...

20 – English WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

English – 21 WORKING TECHNIQUES Working methods • Before you start clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollows etc. • Start at whichever end of the area is easiest, and clear an open space from which to work. • Work systematicall...

22 – English WORKING TECHNIQUES • To fell a tree forwards, the bottom of the tree should be pulled backwards. Pull the blade backwards with a quick, firm movement. • Large stems must be cut from two sides. First determine which direction the stem will fall. Make the first cut on the felling side. Th...

English – 23 WORKING TECHNIQUES Grass trimming with a trimmer head Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut. • The cord can easily remove grass and...

24 – English MAINTENANCE Carburetor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaust ...

English – 25 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting at...

26 – English MAINTENANCE Muffler CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter. The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The...

English – 27 MAINTENANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. Clean the filter every 25 hours, or more regu...

28 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

English – 29 TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

30 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

1 Tap-N-Go Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"

´®z+R:e¶5k¨ ´®z+R:e¶5k¨ 1 Poly Trim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10