JL Audio SLPK-CAN-SPYDER1 - Manual
JL Audio SLPK-CAN-SPYDER1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Before drilling, always make sure that you are not; Position foam strips as shown on each pod.
- Page 5 – Continued on Next Page; steP; C o n G R a t u l a t I o n s !; You have completed the installation for this model!
- Page 6 – I n C l u d e d H a R d W a R e; ) 3” x 3” Wax Square; s P e C I F I C a t I o n s; Ohms; P o W e R R e C o m m e n d a t I o n
I n s t a l l a t I o n G u I d e
for the
SLPK-CAN-SPYDER1
sKu#94491& 94490
Thank you for choosing a JL Audio Slampak
®
for your motorcycle sound system. With proper
installation, your new vehicle-specific enclosed sound system will deliver years of listening pleasure.
We strongly recommend that you have your new Slampak
®
installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
®
be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
s t e P 1
Empty out the front storage space of the motorcycle so that
you have a clean area to work in.
If you are only installing the pods, skip to
steP 16
.
Continued on Next Page
s t e P 2
Remove the bottom panel above the rear tire as show here
s t e P 3
Lift the seat, remove the panel that simulates a gas tank at
the top center of the motorcycle. Remove the two panels
labelled “can-am” (one on each side of the motorcycle) and
the two panels labelled “spyder” (one on each side of the
motorcycle).
SLPK-CAN-SPYDER1_INSTR_SKU# 011312
InstallatIon
d I F F I C u l t Y :
3
5
o u t
o F
estImated tIme:
1 HouR
SlamPak
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Continued on Next Page SLPK-CAN-SPYDER1_INSTR_SKU# 011312 s t e P 1 5 Install the 3/8-16 x 1-1/4” Hex Head Bolt through the included Split Lock Washer, the 1-1/4” Fender Washer and the hole drilled in steP 14 into the enclosure, tighten this fastener down. Once this fastener is tight, the front air ...
Continued on Next Page SLPK-CAN-SPYDER1_INSTR_SKU# 011312 s t e P 3 0 Again, secure all cables along the full run to ensure that they cannot get tangled in any moving parts or the exhaust system. The signal and speaker wires will join with the power cables that came up the side of the motorcycle and...
SLPK-CAN-SPYDER1_INSTR_SKU# 011312 Page 6• JL Audio, Inc 2009 All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL...
