Page 2 - DECLARATION OF CONFORMITY; AS DEFINED BY THE COUNCIL DIRECTIVE
CV-M536/538/539 DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPATIBILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLLOWING PROVISIONS APPLYING TO IT. EN-50081-1 EN-50082-1
Page 3 - Table of Contents
- 2 - CV-M536/538/539 Table of Contents Table of Contents ....................................................................................................................................... 21. General .................................................................................................
Page 4 - Standard Composition; Options
- 3 - CV-M536/538/539 1. General The model CV-M536 series is a new remote micro-head camera system featuring virtually identicalperformance and function of the popular CV-M50 standard machine vision camera. Precisely installed CCD imager (1/2") and miniature size (ø17mm) allows access to very co...
Page 6 - Locations and Functions
- 5 - CV-M536/538/539 4. Locations and Functions 4-1. CCU 4-2. HEAD a ) CV-M536 b) CV-M538/539 1 12P connector : To connect camera head with camera control unit (For Camera Head) 2 Video output connector : To output video VS1.0Vp-p (BNC connector) 3 SW1 switch : To set shutter speed and function mod...
Page 8 - Functions and Operations
- 7 - CV-M536/538/539 6. Functions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be4.0V p-p +/- 2.0V at the input with the 75 Ohm termination ON. To change to n...
Page 9 - Ext. trigger to pin 5 on 6 pin multi connector.
- 8 - CV-M536/538/539 To use this modeSet: SW1-4 to ON for ext. trigger shutterSW1-5 to OFF for field accumulationSW1-6 to ON for non-interlacedSW1-1,2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector. (If used).75 Ohm terminati...
Page 11 - Cautions in the Pulse Width Control Mode.
- 10 - CV-M536/538/539 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. ...
Page 12 - The Start /Stop trigger will work in 3 modes:
- 11 - CV-M536/538/539 6.3.3. Start/Stop Trigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation.2. Interlaced with field accumulation.3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext. trigger pulse an...
Page 15 - Cautions in the Long Time Exposure Mode.; It is recommended not to use exposure
- 14 - CV-M536/538/539 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . CCIR: 1/25 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext. HD signal (4.0 Vp-p ± 2.0V at 75 Ohm termi...
Page 16 - Caution on Mode Setting.; Before making any mode or jumper setting turn the power OFF.
- 15 - CV-M536/538/539 SW1-1 MSB SW1-2 SW1-3 LSB Shutter speed (sec.) Normal shutter Ext. trigger shutter OFF OFF OFF Off 1/60 (1/50) OFF OFF ON 1/100 1/125 OFF ON OFF 1/250 OFF ON ON 1/500 ON OFF OFF 1/1000 ON OFF ON 1/2000 ON ON OFF 1/4500 ON ON ON 1/10,000 Switch no. Switch function Mode setting ...
Page 18 - Caution on Jumper Setting.; Caution for Pixel Clock Output.
- 17 - CV-M536/538/539 7.3. Jumper Settings Caution on Jumper Setting. Before making any mode or jumper setting turn the power OFF. Jumpers for mode setting are found on the boards PK8054 & PK8057. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD i...
Page 19 - Jumpers are shorted with a
- 18 - CV-M536/538/539 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. To remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8054 Side B 7.4.2. Board PK8057 Side A R127 J...
Page 20 - Adjustment of Video Signal Output Level; Location of VR3 to VR5 on PK8056 board is as follow.
- 19 - CV-M536/538/539 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjustpotentiometers VR3, VR4 and VR5 on the PK8056 board while measuring their levels at the video outputconnector.This adjustment should only be d...
Page 21 - External Appearance
- 20 - CV-M536/538/539 9. External Appearance Unit : mm (inches) 9.1 CCU 9.2 HEAD a ) CV-M536 b) CV-M538/539 M15.5 x 0.5 60 (2.36) 14 13.5 11 21.5 ø16.5(0.64) ø17(0.66) 5.1 ± 0.2 (in glass t=0.75) 4.8 ± 0.2 (in air) X Y Z (0.84) (0.43) (0.53)(0.55) 50 (1.97) 40 (1.57) 20 26 (1.02) (1.02) (0.79) 12.7...
Page 22 - Note: Above specifications are subject to change without notice.; Relat
- 21 - CV-M536/538/539 10. Specifications Scanning system CCIR 625 lines EIA 525 lines 25 frames/sec. 30 frames/sec. CCD sensor Monochrome 1/2" Hyper HAD IT CCD Sensing area 6.6 mm (h) x 4.8 mm (v) Effective pixels 752 (h) x 582 (v) 768 (h) x 494 (v) Elements in video output 737 (h) x 575 (v) 75...
Page 24 - Users Mode Settings
JAI America, Inc., USA Suite 45023046 Avenida de la CarlotaLaguna Hills, CA 92653U S APhone +1 949 472 5900Fax +1 949 472 5908www.jai.com JAI Corporation, Japan German Industry Center1-18-2 Hakusan, Midori-kuYokohama,Kanagawa 226-0006, JapanPhone +81 45 933 5400Fax +81 45 931 6142www.jai-corp.co.jp ...