JAI CV-A1-20 - Manual

CV-A1-20 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Fig. 2. 12-pin connector. Plugs for cable: HR10A-10P-12S 5.2. 6-pin Multi-connector (TRIGGER) Type: HR10A-7R...

CV-A1-20 5.4. CV-A1 Block Diagram Fig. 8. Block diagram. 6. Functions and Operations 6.1. Basic functions Some of the primary camera functions need a general introduction before the operation modes are described. The list below shows the primary functions from the command list. SM Shutter Mode Norma...

CV-A1-20 Binning mode BI is a function where the signal charge from 2 or more adjacent pixels are added together and read out as one pixel. A resulting full frame with lower resolution can be read out with a higher rate. By adding 2 pixels together, the sensitivity is doubled. The CV-A1-20 has both ...

CV-A1-20 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, the camera will synchronize to it. If no external sync signals are applied, the camera will operate with its i...

CV-A1-20 6.4. External Trigger Modes This camera has 6 external asynchronous trigger modes, which can be set by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. (HC=0, HC=1) 3. Frame Delay read out m...

CV-A1-20 6.5. Edge Pre-select Mode The exposure starts at the first HD pulse after the trigger leading edge. It stops and is read out after the duration of the shutter time selected. It can be the first 9 step in normal or 1023 steps in programmable shutter. SM=0 or SM=1. Shutter selections SH ≥ 10 ...

CV-A1-20 6.7. Frame-delay read out Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse. The accumulation can be either H synchronous or H asynchronous. HC=0 or HC=1. In H synchronous mode the accumulation starts at the ...

CV-A1-20 6.11. Other Functions. Gain and analogue settings. !! Do not adjust these settings unless you have knowledge to video adjustments !! The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 12 dB range. Normal 7...

CV-A1-20 7.4. Internal Switch and Jumper Settings For VD and HD input/output and termination refer to “6.2. Input-output of HD/VD Signals.” For alternative connections of pin #10 and #11 on 12-pin connector, jumper JP1, JP2, JP3, JP4 and JP5 can be used. Refer “5.3. Input and Output Circuits.” Jumpe...

CV-A1-20 9. Specifications Specifications CV-A1-20 Scanning system Progressive 1068 lines 11.2 frames/sec. Pixel clock 20.00 MHz Line frequency 11.962 kHz (1672 pixel clock/line) Frame rate for full frame 11.2 frames/sec. (1068 lines/frame) CCD sensor 1/2” progressive monochrome IT CCD Sensing area ...

CV-A1-20 11. Users Record Camera type: CV-A1-20 Revision: (Revision B) Serial No. …………….. Users Mode Settings Users Modifications DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPABILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWIN...