IVES 232TGSL - Manual

Refer All Communications to the Nearest

Ingersoll--Rand Office or Distributor.



Ingersoll--Rand Company 2002

Printed in U.S.A.

04577441

Form P7470
Edition 2
December, 2002

OPERATION AND MAINTENANCE MANUAL

FOR MODEL 232TGSL

(THUNDER GUN STREET LEGAL)

1/2” IMPACT WRENCH

Model 232TGSL Impact Wrench is designed for use in general automotive repair, body

shops, front end service and light truck and farm equipment applications.

IMPORTANT SAFETY INFORMATION ENCLOSED -- SAVE THESE INSTRUCTIONS

READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS PRODUCT

IT IS YOUR RESPONSIBILITY TO MAKE THIS SAFETY INFORMATION

AVAILABLE TO OTHERS THAT WILL OPERATE THIS PRODUCT

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY

PLACING TOOL IN SERVICE

•

Always install, operate, inspect and maintain this

product in accordance with all applicable standards

and regulations (local, state, country, federal, etc.).

•

Always use clean, dry air at 90 psig (6.2 bar/620 kPa)

maximum air pressure at the inlet. Higher pressure

may result in hazardous situations including excessive

speed, rupture, or incorrect output torque or force.

•

Be sure all hoses and fittings are the correct size and

are tightly secured. See Dwg. TPD905--2 for a typical

piping arrangement.

•

Ensure an accessible emergency shut off valve has

been installed in the air supply line, and make others

aware of its location.

•

Do not use damaged, frayed or deteriorated air hoses

and fittings.

•

Keep clear of whipping air hoses. Shut off the

compressed air before approaching a whipping hose.

•

Always turn off the air supply and disconnect the air

supply hose before installing, removing or adjusting

any accessory on this tool, or before performing any

maintenance on this tool.

•

Do not lubricate tools with flammable or volatile

liquids such as kerosene, diesel or jet fuel. Use only

recommended lubricants.

•

Keep work area clean, uncluttered, ventilated and

illuminated.

•

Do not remove any labels. Replace any damaged label.

USING THE TOOL

•

Always wear eye protection when operating or

performing maintenance on this tool.

•

Always wear hearing protection when operating this

tool.

•

Always use Personal Protective Equipment

appropriate to the tool used and material worked.

This may include dust mask or other breathing

apparatus, safety glasses, ear plugs, gloves, apron,

safety shoes, hard hat and other equipment.

•

Prevent exposure and breathing of harmful dust and

particles created by power tool use.

Some dust created by power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

-- lead from lead based paints,

-- crystalline silica from bricks and cement and

other masonry products, and

-- arsenic and chromium from chemically

treated lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic

particles.

•

Keep others a safe distance from your work area, or

ensure they use appropriate Personal Protective

Equipment.

•

This tool is not designed for working in explosive

environments, including those caused by fumes and

dust, or near flammable materials.

•

This tool is not insulated against electric shock.

•

Be aware of buried, hidden or other hazards in your

work environment. Do not contact or damage cords,

conduits, pipes or hoses that may contain electrical

wires, explosive gases or harmful liquids.

•

Keep hands, loose clothing, long hair and jewelry

away from working end of tool.

•

Power tools can vibrate in use. Vibration, repetitive

motions or uncomfortable positions may be harmful

to your hands and arms. Stop using any tool if

discomfort, tingling feeling or pain occurs. Seek

medical advice before resuming use.

•

Keep body stance balanced and firm. Do not

overreach when operating this tool. Anticipate and be

alert for sudden changes in motion, reaction torques,

or forces during start up and operation.

•

Tool and/or accessories may briefly continue their

motion after throttle is released.

•

To avoid accidental starting -- ensure tool is in “off”

position before applying air pressure, avoid throttle

when carrying, and release throttle with loss of air.

•

Ensure work pieces are secure. Use clamps or vises to

hold work piece whenever possible.

•

Do not carry or drag the tool by the hose.

•

Do not use power tools when tired, or under the

influence of medication, drugs, or alcohol.

•

Never use a damaged or malfunctioning tool or

accessory.

F
E
P