Invacare Tracer SX5 - Manual

Invacare Tracer SX5 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – REMOVING EXISTING WHEELCHAIR COMPONENTS; REMOVING THE REAR WHEELS; This kit contains the following items:
Page 3 – REMOVING THE FLIP BACK ARMS
Page 4 – INSTALLING THE RECLINING BACK; Remove the components listed in REMOVING EXISTING WHEELCHAIR; REMOVING THE FORK/CASTER ASSEMBLIES - WHEELCHAIRS; Locknut; WHEELCHAIRS UNDER 20-INCHES WIDE ONLY
Page 5 – INSTALLING THE OFFSET WHEEL BRACKETS (FIGURE 5); = RIGHT offset wheel bracket; INSTALLING THE REAR ARM SOCKETS (FIGURE 4); should be facing the REAR wheelchair when mounted.
Page 6 – INSTALLING THE RECLINING BACK ASSEMBLY (FIGURE 6); the wheelchair frame.
Page 7 – INSTALLING THE REAR WHEELS; WARNING; ASSEMBLIES in the Owners Manual, part number 1110550.; All Wheelchair Widths.; NOTE: Arm socket and back upholstery
Page 8 – procedure of the instruction sheet.; FIGURE 7 - INSTALLING THE BOLT-ON WHEEL LOCKS; Bolt and Locknut; INSTALLING/ADJUSTING THE WHEEL LOCKS; Invacare for ordering information.
Page 9 – HOLDS; the occupied wheelchair in place when pushed.; FIGURE 8 - INSTALLING WHEEL LOCK SHOE EXTENSION; if pneumatic tire) into the tire when engaged.
Page 10 – CONVERTING ARMS FROM FLIP-BACK STYLE TO; from the spring button holes.; FIGURE 10 - ADJUSTING THE WHEEL LOCKS; into the tire when engaged.; still cannot be achieved, contact a qualified technician.
Page 11 – INSTALLING THE SPREADER BAR; RECLINER section of the Owners Manual, part number 1110550.; INSTALLING THE ANTI-TIPPERS; arm socket from moving. See DETAIL E in FIGURE 11.
Page 12 – USING THE RECLINER; INSTALLING THE HEADREST AND PILLOW (FIGURE 12); facing the front of the wheelchair.

Loading the manual

Part No. 1110194 Rev A

Tracer® SX5 Recliner Conversion Kit

Assembly and Installation Instructions

SAVE THESE INSTRUCTIONS

NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. contact

Carrier/Dealer for further instruction.

SAFETY SUMMARY

To ensure the safe installation of the Recliner Conversion Kit, these instructions

MUST be followed:

WARNING

DO NOT install or use this equipment without first reading and understanding

these instructions and the Owners Manual, part number 1110550. If you are

unable to understand the Warnings, Cautions or Instructions, contact a

healthcare professional, dealer or technical personnel before attempting to

install this equipment - otherwise, injury or damage may occur.
AFTER conversion of the wheelchair and BEFORE USE of the recliner, read

the GENERAL GUIDELINES and RECLINER sections of the Owners Manual,

part number 1110550, for recliner operation instructions.

INSTALLATION WARNING

After ANY adjustments, repair or service and before use, make sure all attaching

hardware is tightened securely - otherwise injury or damage may occur.
SX5 Recliners MUST have 8-inch casters installed. If the wheelchair originally

had 6-inch casters installed, seat-to-floor height adjustments MUST be made.

Seat-to-floor adjustments will also be necessary for certain 8-inch caster

mounting positions. Refer to the SEAT-TO-FLOOR section in the Owners

Manual, part number 1110550, for these adjustments.
SX5 Recliners CANNOT be used with the following options/accessories: one-

arm drive, solid folding seat, IV/O2 holder, O2 holder, Model 2218 IV rod,

amputee attachments or quick release axles. These options/accessories

MUST be removed prior to the conversion of the wheelchair.
SX5 Recliners MUST have properly installed and adjusted wheel locks and

anti-tippers. Refer to INSTALLING/ADJUSTING THE WHEEL LOCKS

and INSTALLING THE ANTI-TIPPERS in this instruction sheet. Failure to

observe this warning can result in serious injury.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - REMOVING EXISTING WHEELCHAIR COMPONENTS; REMOVING THE REAR WHEELS; This kit contains the following items:

Tracer® SX5 Recliner Conversion Kit 2 Part No. 1110194 Rev A REMOVING EXISTING WHEELCHAIR COMPONENTS To convert the wheelchair to a recliner, the following components MUST be removed:Rear WheelsArmsBack CanesBack UpholsteryWheel LocksFork/Caster Assemblies - if wheelchair is 14 to 18-inches wide. RE...

Page 3 - REMOVING THE FLIP BACK ARMS

Part No. 1110194 Rev A 3 Tracer® SX5 Recliner Conversion Kit Back Cane Wheelchair Frame Locknut FIGURE 1 - REMOVING THE BACK CANES Hex Screw OUTSIDE OF WHEELCHAIR INSIDE OF WHEELCHAIR REMOVING THE WHEEL LOCKS (FIGURE 2) 1. Ensure the wheel lock is in the open (unlocked) position.2. Remove the bolt a...

Page 4 - INSTALLING THE RECLINING BACK; Remove the components listed in REMOVING EXISTING WHEELCHAIR; REMOVING THE FORK/CASTER ASSEMBLIES - WHEELCHAIRS; Locknut; WHEELCHAIRS UNDER 20-INCHES WIDE ONLY

Tracer® SX5 Recliner Conversion Kit 4 Part No. 1110194 Rev A INSTALLING THE RECLINING BACK 1. Remove the components listed in REMOVING EXISTING WHEELCHAIR COMPONENTS in this instruction sheet. 2. Perform the following to complete installation of the reclining back: Install the Rear Arm SocketsInstal...