Invacare 9000 - Manual
Invacare 9000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – be maintained at all times.; FIGURE 2 - ADJUSTING THE; FIGURE 1 - INSTALLING THE; Release Buttons
- Page 3 – Flat Surface
- Page 4 – JYMNI ANTI-TIPPER CHART; measurement MUST be taken with the anti-tipper on a flat surface.; JYMNI
Part No. 1058751
1
9000 Series and Jymni Anti-tippers
SAFETY SUMMARY
To ensure the safe installation and use of the Anti-tippers, these instructions
MUST be followed:
WARNING
Do not operate this equipment without first reading and understanding this
instruction sheet and the owner's manual, part number 1056953, for the
9000 series wheelchairs or the owner's manual, part number 1100868, for
Jymni wheelchairs. If you are unable to understand the warnings, cautions,
and instructions, contact a healthcare professional, dealer or a qualified
technician before attempting to use this equipment - otherwise injury or
damage may result.
Anti-tippers are specific to the different seat-to-floor angles and/or seat-to-floor
heights. Refer to the chart in this instruction sheet for correct usage and
adjustment. If these requirements CANNOT be achieved, DO NOT use the
wheelchair. Contact a qualified technician. If changing the seat-to-floor height
with or without a change to seat-to-floor angle, the correct anti-tippers MUST be
used to maintain a 1-1/2 to 2-inch ground clearance.
9000 WHEELCHAIRS WITH A SEAT-TO-FLOOR ANGLE OF 0°
OR 3° AND
JYMNI NON-RECLINERS ONLY - If so equipped, anti-tippers MUST be
attached at all times. Inasmuch as the anti-tippers are an option for 0°
or 3°
on
this wheelchair (You may order with or without the anti-tippers), Invacare
strongly recommends ordering the anti-tippers as a safeguard for the wheelchair
user.
9000 WHEELCHAIRS WITH A SEAT-TO-FLOOR ANGLE OF 6° ONLY - If
changing the seat-to-floor angle to 6°, anti-tippers MUST BE ORDERED AND
INSTALLED.
JYMNI RECLINERS AND JYMNI WHEELCHAIRS WITH 1-INCH
FORWARD REAR WHEEL POSITIONERS ONLY - Anti-tippers MUST
be attached at all times.
Anti-tippers MUST be fully engaged and spring buttons fully protruding
out of adjustment holes, BEFORE using the wheelchair.
Ensure both anti-tippers are adjusted to the same mounting hole.
Anti-tipper kits include the following parts:
Description
Quantity
Description
Quantity
Anti-tipper
2
Anti-rattle
2
9000 Series and Jymni Anti-tippers
Assembly, Installation and Operating Instructions
Adjustable Anti-tipper Kit Nos. 1058752, 1058836, 1064520 and 1101960
Non-adjustable Anti-tipper Kit Nos. 1113764, 1113765 and 1113766
NOTE: Check all parts for shipping damage before using. In case of damage, DO NOT use.
Contact the dealer/carrier for further instructions.
SAVE THESE INSTRUCTIONS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
9000 Series and Jymni Anti-tippers 2 Part No. 1058751 INSTALLING ANTI-TIPPERS (FIGURE 1) 1. Remove plug button (not shown) from end of rear frame tubing and install anti-rattles if not already installed. 2. Press the release buttons IN and insert the anti-tippers with the anti-tipper wheels pointin...
Part No. 1058751 3 9000 Series and Jymni Anti-tippers 9000 SERIES ANTI-TIPPER CHARTS (FIGURE 3) NOTE: Refer to the following charts to ensure the correct anti-tipper is installed on the wheelchair. Seat-to-Floor heights are approximate depending on front caster size and type. Refer to SECTION 5 of ...
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. and Jymni are trademarks 800-333-6900 800-668-5324 of Invacare Corporat...
