Intel ZT 4807 - Manual

Document Organization This Technical Product Specification describes the operation and use of the Intel NetStructure ® ZT 4807 Packet Switched Rear Panel Transition Board. The following summarizes the focus of each major section of this Specification. Chapter 1, “ Introduction , ” introduces the key...

1. Introduction This chapter provides a brief introduction to the Intel NetStructure ® ZT 4807 Packet Switched Rear Panel Transition Board (RPIO). It includes a product definition, a list of product features, a “ ZT 4807 Connector Plate ” figure, a functional block diagram, and a description of each...

1. Introduction Functional Blocks Below is a functional block diagram of the ZT 4807. The topics following the diagram provide overviews of the ZT 4807's functional blocks. Functional Block Diagram ZT 4807 SPEAKER J5 VIDEO (J19) USB 0 (J13) USB 1 (J14) COM2 (J17) COM1 (J16) (J10) (J11-J12) (J6) KEYB...

1. Introduction Video Interface The ZT 4807 provides rear-panel access to the host processor board VGA accelerator. The host processor board VGA accelerator is connected via RPIO connector J5 to J19 , a 15-pin VGA connector on the ZT 4807 Connector Plate . Note: Video does not function properly if d...

2. CompactFlash Option CompactFlash connector J12 on the ZT 4807 provides external, solid state, secondary IDE channel capability to a processor board such as the Intel NetStructure ® ZT 5504 System CPU Board with Intel Pentium ® III processor. This connector is designed to accommodate CompactFlash ...

2. CompactFlash Option 5.0V operation has the advantage of allowing master/slave operation, with an additional drive connected to the secondary IDE connector J11 on the ZT 4807. See the “ SW4-1 (Secondary IDE Master/Slave Selection) ” topic in Chapter 3, “Configuration,” for more information about c...

3. Configuration The ZT 4807 includes several options that tailor the operation of the board to requirements of specific applications. Some options are configured with a switch or by cuttable traces. Configure a switch option by closing or opening a DIP switch. Configure a cuttable trace option by i...

3. Configuration Cuttable Traces The ZT 4807 includes several cuttable traces (0 Ω shorting resistors) that allow the user to configure certain options not configurable through the processor board's BIOS Setup Utility. In most cases, the default settings are appropriate for normal operation; however...

A. Specifications This Appendix describes the electrical, environmental, and mechanical specifications of the ZT 4807. It includes illustrations of the board dimensions and connector locations, as well as connector pinout tables. Electrical Specifications Power Requirements Minimum Typical Maximum S...

A. Specifications Board Dimensions and Weight Mechanical dimensions for the ZT 4807 are shown in the "Board Dimensions" illustration and outlined below. Board Length: 80mm (3.150 in) Board Width: 233.35mm (9.187 in) Board Thickness: 1.6mm (0.063 in) Board Weight: 202 g (7.13 oz) Board Dimens...

A. Specifications Connectors As shown in the “ Connector Locations ” drawing, the ZT 4807 includes several connectors to interface with application-specific devices. A brief description of each connector is given in the “Connector Assignments” table. A detailed description and pinout for each connec...

A. Specifications Cables Intel recommends the following cables for interfacing to the ZT 4807. IDE For proper operation, Intel recommends 80-conductor IDE cables for external IDE connection. If the external IDE device is configured in a master/slave combination with an on-board IDE device (CompactFl...

B. Agency Approvals Regulatory Information FCC (USA) This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is opera...

B. Agency Approvals AC and/or DC Power Safety Warning (AC and/or DC Powered Units) The AC and/or DC power cord is your unit’s main AC and/or DC disconnecting device, and must be easily accessible at all times. Auxiliary AC and/or DC On/Off switches and/or circuit breaker switches are for power contr...

D. Intel NetStructure ® Compute Boards & Platform Products Limited Warranty Intel warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for two (2) year(s) following the latter of: (i) the date of purchase only if you regi...

C. Customer Support C. Customer Support This appendix offers technical and sales assistance information for this product, and information on returning an Intel NetStructure ® product for service. Technical Support and Return for Service Assistance For all product returns and support issues, please c...