Intel SC5275-E - Manual

Preface Intel® Entry Server Chassis SC5275-E User Guide vi strap attached to chassis ground  any unpainted metal surface  on your server when handling parts. ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After remo...

Preface Intel® Entry Server Chassis SC5275-E User Guide vii 5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached to chassis ground of the system—any unpainted metal surface—when handling components. 6. Do not operate the system with the chassis cover...

Preface Intel® Entry Server Chassis SC5275-E User Guide ix durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend. Das System wurde für den Betrieb in einer normalen Büroumgebu...

Preface Intel® Entry Server Chassis SC5275-E User Guide xi télécommunications de votre modem durant un orage. Muni d'une prise murale correctement mise à la terre. Suffisamment spacieux pour vous permettre d'accéder aux câbles d'alimentation (ceux-ci étant le seul moyen de mettre le système hors ten...

Contents Intel® Entry Server Chassis SC5275-E User Guide xv Contents Warnings ......................................................................................................... v 1 Chassis Description ....................................................................................... 1 Ki...

Contents Intel® Entry Server Chassis SC5275-E User Guide xvi Replacing a Front System Fan ..................................................................................... 31 Replacing a Rear System Fan ..................................................................................... 32 Repl...

Contents Intel® Entry Server Chassis SC5275-E User Guide xvii Figure 6. Removing the 3.5-inch EMI Shield ............................................................................. 14 Figure 7. Installing a Floppy Drive .................................................................................

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 1 1 Chassis Description Kit Contents The chassis subassembly kit includes this product guide and a box that includes two pair of 5.25-inch external drive rails, four different types of mounting screws, and two brackets for the opt...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 2 Chassis Front View TP00053 A B C E F D A. Front panel controls and indicators B. 5.25-inch removable media drive bays C. 3.5-inch removable media drive bay D. Internal hard drive bay cage (behind door) E. Security lock F. USB po...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 3 Front Panel Controls and Indicators TP00080 A C E G I B D F H A. Power / sleep LED B. Power button C. NMI button D. Reset button E. Sleep button F. NIC 1 activity LED G. NIC 2 activity LED H. Hard drive activity LED I. Status LE...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 4 Chassis Rear View TP00834 B A F D E C A. Alternate Serial B port knockout B. Alternate ICMB or external SCSI knockout C. AC input power connector D. Power supply E. Fan F. I/O ports* G. Expansion slot covers H. ICMB or external ...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 5 Peripherals 5.25-inch Removable Media Drive Bays The upper bays are designed for removable media peripherals. You can install up to two half-height peripherals. 3.5-inch Hard Drive Bays The chassis supports up six drives dependi...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 6 Power Supply The 600-Watt PFC non-redundant power supply is auto ranging for either 100-127 VAC or 200-240 VAC operation. Checking the Power Cord WARNING Do not attempt to modify or use a supplied AC power cord if it is not the ...

1 Chassis Description Intel® Entry Server Chassis SC5275-E User Guide 7 Mechanical Locks The front bezel has a two-position lock to prevent access to the hard drives and the interior of the chassis. A padlock loop is included with the chassis and can be installed at the rear of the chassis. TP00055 ...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 9 2 Setting Up the Chassis This chapter describes how to set the server up for the first time. With the exception of replacing the front panel board (discussed in Chapter 4), it is necessary to remove only the left access cover...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 10 Warnings and Cautions These warnings and cautions apply whenever you remove the access cover(s) to access components inside the server. Only a technically qualified person should integrate and configure the server. WARNINGS ...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 11 Remove the Access Cover Observe the safety and ESD precautions at the beginning of this chapter. For ease of installation, before beginning lay the chassis on its right side, with the left access cover facing up. 1. If the s...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 12 Remove the Front Bezel 1. Pull the left side of the bezel forward to disengage the tabs (facing up in the following figure). See number 1 in the figure. 2. Remove the bezel from the tabs at the right side of the chassis (fac...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 13 Install the I/O Shield ✏ NOTE An ATX 2.03-compliant I/O shield should be provided with your server board. The shield is required by Electromagnetic Interference (EMI) regulations. It minimizes EMI and ensures proper cooling ...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 14 Install the Server Board Standoffs and Bumpers The location of the standoffs and bumpers varies by server board. Read and follow the instructions provided with the server board Quick Start User’s Guide for proper standoff an...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 15 8. Slide the drive into the chassis. When properly positioned, the holes in the side of the drive align with the threaded holes in the chassis frame. 9. Secure the drive to the side of the chassis with two screws. Note that ...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 16 IDE Requirements If no drives are present on an IDE channel, the cable must be removed. If only one drive is installed, it should be connected at the end of the cable. ✏ NOTE To disable the IDE controller: If you plan to dis...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 19 Install the Server Board 1. Remove and save the four screws that secure the drive cage to the chassis. Two screws are at the front of the chassis and two are at the side of it. 2. Slide the drive cage out of the chassis. You...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 23 Connect Cables to the Server Board See your server board product guide or Quick Start User’s Guide for connector locations. 1. Connect the power cables to the server board. • The large plug labeled P1 plugs into the main pow...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 24 Installing an Add-in Board You may want to install an operating system before installing any add-in boards. If so, skip this step and return to it when you are ready. CAUTIONS Do not overload the server board by installing a...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 26 Install the Front Bezel 1. Angle the bezel toward the chassis as shown by number 1 in the figure below. 2. Insert the latches on the right side of the bezel (facing down in the figure below) into the corresponding slots in t...

2 Setting Up the Chassis Intel® Entry Server Chassis SC5275-E User Guide 27 Install the Access Cover 1. Place the cover so the tabs on the cover fit into the slots on the server. The cover should be flush against the chassis. 2. Slide the cover forward until it stops (letter A in the figure below). ...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 29 3 Maintaining Your Server This chapter describes how to replace components in your server after it has been set up. Tools and Supplies Needed Phillips (cross head) screwdriver (#2 bit) Small flathead screwdriver Antistatic ...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 31 Replacing Fans The chassis contains two replaceable system fans. The power supply fan(s) are not replaceable. Your replacement fan should be the same size and type as the fan you are removing. Replacing a Front System Fan S...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 32 9. Slide the new fan in through the fan opening. Make sure the airflow is towards the server board. This means the label should face the server board. 10. Replace the nylon rivets to attach the fan to the hard drive bay cag...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 33 Replacing the Power Supply WARNINGS Hazardous conditions, power supply : Hazardous voltage, current, and energy levels are present inside the power supply. There are no user-serviceable parts inside it; servicing should be ...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 34 Replacing the Front Panel Board 1. Remove the left access cover. 2. Remove the bezel. 3. Remove the two screws at the rear of the chassis that hold the right access cover in place. 4. Remove the right access cover. A rectan...

3 Maintaining Your Server Intel® Entry Server Chassis SC5275-E User Guide 36 Replacing the USB Cable 1. Remove the left access cover. 2. Remove the bezel. 3. Disconnect the existing USB cable from the server board. 4. Disconnect the bracket the attaches the USB cable to the front of the chassis. 5. ...

4 Technical Reference Intel® Entry Server Chassis SC5275-E User Guide 39 4 Technical Reference Power Supply Specifications 600 Watt Single Power Supply Input Voltages 600 Watt Power Supply 100-127 V ∼ at 50/60 Hz; 6.5 A max. 200-240 V ∼ at 50/60 Hz; 3.2 A max. 600 Watt Single Power Supply Output Vol...

4 Technical Reference Intel® Entry Server Chassis SC5275-E User Guide 40 System Environmental Specifications Table 5. Environmental Specifications Temperature Non-operating Operating –40 ° to 70 °C. 5 ° to 35 °C; derated 0.5 °C for every 1000 ft (305 m) to a maximum of 10,000 ft. Humidity Non-operat...

Equipment Log and Worksheets Intel® Entry Server Chassis SC5275-E User Guide 41 Equipment Log and Worksheets Equipment Log Use the blank equipment log provided here to record information about your server. You will need some of this information when you run the SSU. Item Manufacturer Name and Model ...

Equipment Log and Worksheets Intel® Entry Server Chassis SC5275-E User Guide 43 Current Usage Calculating Power Usage The total combined wattage for your configuration must be less than the wattage rating for your power supply. Use the two worksheets in this section to calculate the total used by yo...

Regulatory and Compliance Information Intel® Entry Server Chassis SC5275-E User Guide 45 Regulatory and Compliance Information Product Regulatory Compliance Product Safety Compliance The Intel® Entry Server Chassis SC5275-E complies with the following safety requirements: UL60950 – CSA 60950(USA / C...

Regulatory and Compliance Information Intel® Entry Server Chassis SC5275-E User Guide 46 GB 17625 - (Harmonics) CNCA Certification (China) Certifications / Registrations / Declarations UL Certification (US/Canada) CE Declaration of Conformity (CENELEC Europe) FCC/ICES-003 Class A Attestation (USA/Ca...

Regulatory and Compliance Information Intel® Entry Server Chassis SC5275-E User Guide 47 Regulatory Compliance Country Marking BSMI Certification Number & Class A Warning Taiwan GOST R Marking Russia RRL MIC Mark Korea China Compulsory Certification Mark China Electromagnetic Compatibility Notic...

Regulatory and Compliance Information Intel® Entry Server Chassis SC5275-E User Guide 49 VCCI (Japan) English translation of the notice above: This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) from Information Technology Equipment. If this is us...

Regulatory and Compliance Information Intel® Entry Server Chassis SC5275-E User Guide 50 Regulated Specified Components To maintain the UL listing and compliance to other regulatory certifications and/or declarations, the following regulated components must be used and conditions adhered to. Interch...

Getting Help Intel® Entry Server Chassis SC5275-E User Guide 51 Getting Help World Wide Web http://support.intel.com/support/motherboards/server/chassis/SC5275E Telephone All calls are billed US $25.00 per incident, levied in local currency at the applicable credit card exchange rate plus applicable...

Warranty Intel ® Entry Server Platform SR1325TP1-E User Guide 53 Warranty Limited Warranty for Intel ® Chassis Subassembly Products Intel warrants that the Products (defined herein as the Intel ® chassis subassembly and all of its various components and software delivered with or as part of the Prod...

Warranty Intel® Entry Server Chassis SC5275-E User Guide 54 Warranty Limitations and Exclusions These warranties replace all other warranties, expressed or implied including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Intel makes no expressed ...

Warranty Intel ® Entry Server Platform SR1325TP1-E User Guide 55 How to Obtain Warranty Service To obtain warranty service for this Product, you may contact Intel or your authorized distributor. North America and Latin America  To obtain warranty repair for the product, please go to the following W...