Page 3 - Contents; Safety Guidelines
iii Contents Safety Guidelines Server Precautions ............................................................................................................... 5Equipment Rack Precautions ............................................................................................... 6 Rack Install...
Page 5 - Before you remove a server cover, observe these safety guidelines:; Server Precautions; WARNINGS; front panel of the server
5 Safety Guidelines Before you remove a server cover, observe these safety guidelines: • Only technically qualified personnel should integrate the server. • Turn off all peripheral devices connected to the server. • Turn off the server using the push-button on/off power switch on the front panel of ...
Page 6 - CAUTIONS; ESD; ESD can; Equipment Rack Precautions; : The equipment rack must be anchored
6 SC5000 Rack Kit Installation Guide CAUTIONS E LECTROSTATIC DISCHARGE (ESD) AND ESD PROTECTION : ESD can damage disk drives, add-in boards, and other components. This server canwithstand normal levels of environmental ESD while hot-swapping SCSIhard disk drives. However, we recommend doing all proc...
Page 7 - : The server is designed for an AC line; Temperature; : The operating temperature of the server, when installed in an; Ventilation; : The equipment rack must provide sufficient airflow to the front
Safety Guidelines 7 O VERCURRENT PROTECTION : The server is designed for an AC line voltage source with up to 20 amperes of overcurrent protection. If thepower system for the equipment rack is installed on a branch circuitwith more than 20 amperes of protection, you must providesupplemental protecti...
Page 9 - Rack Installation Procedures; Intel; Kit Contents
9 Rack Installation Procedures This manual describes the procedure to convert an SC5000 chassis from the pedestal configurationto the rack configuration. It supplements the Intel ® SC5000 Server Chassis Subassembly Product Guide (744708-003). In the following procedures, chassis directions (top, bot...
Page 10 - Remove Feet; Place the chassis on a workbench so the feet hang over the side.
10 SC5000 Rack Kit Installation Guide Remove Feet 1. Place the chassis on a workbench so the feet hang over the side. 2. Remove the four screws (Figure 1, A) that attach the rear foot to the chassis and remove thefoot. 3. Remove the four screws that hold the front foot to the chassis and remove the ...
Page 11 - Remove Top Cover; Slide the cover backward a short distance, until it stops.
Rack Installation Procedures 11 Remove Top Cover 1. Loosen the two thumbscrews that attach the top cover to the chassis. 2. Slide the cover backward a short distance, until it stops. 3. Pull the entire cover outward, straight away from the chassis, to disengage the rows of tabsfrom the notches in th...
Page 12 - Remove 5 1⁄4-Inch Devices; Disconnect the data and power cables from the device.
12 SC5000 Rack Kit Installation Guide Remove 5 ¼-Inch Devices 1. Disconnect the data and power cables from the device. 2. Remove and save the two screws that hold the slide rails to the chassis. OM09381 A B C Figure 3. Removing a 5 ¼-inch Device A. Power cable B. Data cable C. Slide rail
Page 14 - Remove Door; Move the chassis so the door hangs over the edge of your workbench.
14 SC5000 Rack Kit Installation Guide Remove Door 1. Move the chassis so the door hangs over the edge of your workbench. 2. Open the door. 3. Press the plastic clip (Figure 5, A) in towards the chassis. 4. Pull the hinge pin (Figure 5, B) out with one hand while supporting the door with the other. 5...
Page 15 - Remove the hinge plate.
Rack Installation Procedures 15 7. Remove and save the four screws attaching the hinge plate to the chassis. 8. Remove the hinge plate. OM09380 Figure 6. Removing the Hinge Plate
Page 16 - Remove Bezel; Slide the bezel to the right.
16 SC5000 Rack Kit Installation Guide Remove Bezel 1. Press the tab up (Figure 7, A). 2. Slide the bezel to the right. 3. Remove the bezel from the chassis. OM09382 A Figure 7. Removing the Bezel A. Tab
Page 17 - Remove EMI Covers
Rack Installation Procedures 17 Remove EMI Covers 1. Remove and save the two screws that attach the EMI covers to the chassis. 2. Remove all of the EMI covers. There will be one thin cover and up to three wider covers. Donot remove any of the hard drive carriers. OM09376 A Figure 8. Removing the EMI...
Page 18 - Remove Right Side Cover
18 SC5000 Rack Kit Installation Guide Remove Right Side Cover 1. Remove and save the screw at the rear of the chassis (Figure 9, A). 2. Pull up on the black clip (Figure 9, B). 3. Remove and save the black clip (Figure 9, C). 4. Slide the cover backwards and remove it (Figure 9, D). OM09390 A C B D ...
Page 19 - Install Right Side Cover
Rack Installation Procedures 19 Install Right Side Cover 1. Slide the new cover into position (Figure 10, A). 2. Insert the black clip (Figure 10, B). 3. Press the clip down (Figure 10, C). 4. Insert and tighten the screw you removed earlier (Figure 10, D). OM09391 D A B C Figure 10. Installing the ...
Page 20 - Install 5 1⁄4-Inch Devices into the Reorientation Bracket; Remove the two screws that hold the EMI shield in place.
20 SC5000 Rack Kit Installation Guide Install 5 ¼-Inch Devices into the Reorientation Bracket 1. Remove the two screws that hold the EMI shield in place. 2. Remove the EMI shield. 3. Slide the device into the bracket. 4. Insert and tighten the four screws removed when you removed the slide rails. OM...
Page 21 - Install the 5 1⁄4-Inch Reorientation Bracket; Slide the bracket into the chassis.
Rack Installation Procedures 21 Install the 5 ¼-Inch Reorientation Bracket 1. Slide the bracket into the chassis. 2. Insert and tighten five screws. 3. Connect data and power cables to the devices. OM09393 A C B Figure 12. Installing the 5 ¼-Inch Reorientation Bracket A. ScrewB. Data cable C. Power ...
Page 22 - Install Bezel; Position the chassis intrusion switch lock.
22 SC5000 Rack Kit Installation Guide Install Bezel 1. Position the chassis intrusion switch lock. 2. Using a Philips screwdriver, rotate the switch lock ½ turn clockwise. OM09385 D A B C Figure 13. Installing the Chassis Intrusion Lock A. Philips screwdriver B. Chassis intrusion switch lockC. Direc...
Page 23 - Slide it to the left.
Rack Installation Procedures 23 3. Position the bezel. Make sure all of the plastic tabs are aligned with their holes. 4. Slide it to the left. OM09384 A Figure 14. Installing the Bezel A. Tab
Page 24 - Install Screw Plate; Position the Screw Plate.
24 SC5000 Rack Kit Installation Guide Install Screw Plate 1. Position the Screw Plate. 2. Insert and tighten the four screws you removed when you removed the door hinge plate. OM09394 A Figure 15. Installing the Screw Plate A. Screw
Page 25 - Install Front Cover; If you have a hot swap bay installed, remove that plastic cover.
Rack Installation Procedures 25 Install Front Cover 1. For each 5 ¼-inch peripheral, remove the corresponding plastic cover. 2. If you have a hot swap bay installed, remove that plastic cover. 3. Position the bezel by sliding the tabs on the top under the bezel. 4. Tighten the thumbscrews. OM09395 F...
Page 26 - Install Top Cover; Slid the cover forward until it stops.
26 SC5000 Rack Kit Installation Guide Install Top Cover 1. Place the cover so the tabs go into the slots on the server. The cover should be flush against thechassis. 2. Slid the cover forward until it stops. 3. Tighten the two captive screws into the rear of the chassis. OM09170 Figure 17. Installin...
Page 27 - Install Rails
Rack Installation Procedures 27 Install Rails 1. Using two screws for each handle, attach the handles to the chassis. OM09375 Figure 18. Installing the Handles 2. Fully extend the rails. 3. Remove the smallest rail. 4. Position the rail 5. Insert and tighten four screws. B B B B A OM09377 Figure 19....
Page 28 - NOTE
28 SC5000 Rack Kit Installation Guide OM09388 Figure 20. Rails Installed in a Rack ✏ NOTE Your rack may vary from the illustration. Refer to your rack documentationfor information specific to your rack 7. Hold the chassis so the rails on the chassis engage the rails in your rack. You will needsomeon...
Page 31 - ÅÌÛ
iii  ] <í áu<¼ã_M .................................................................................................................... 5 Û¼ã_M ................................................................................................................. 6 ] c ' N ¹KÙY ..................
Page 34 - È 4yÁÃ Vp¥ó¡ Úôä CMOS DBöèë
6 SC5000 ]Û+ ¼ ã - (ESD) ` ESD ±x ESD Ã3#¬E|< tS5J WÊ'Á¦¨ SCSI @¬E|<Ê áu<ù£«7{ÿXW ESD àåÀ|$¾Ñü ESD X¹0Þ; `XÝ9x V puÝX¹0 íüÊÊÞ- )ú ²yáu<
y¼!—Ï)uÝVÚX¥2<6 ¹¤o ESD ±xS5`õ+ S5`õ+Í ESD U#ó ÊhãüÚS5êõ+¢±xûÙêáu<ªÎâ ÚÊ6ñÞüÔþáÐ X´- <6Þ Vp¡SüÔþÐ X<6Þ ÃÑÐ È 4yÁà Vp¥...
Page 42 - üÔ3⁄4 ̈ÎÄÒÔ Ò 5 X B
14 SC5000 ]Û+ & ! ª 1. Ï|
S!ªb¹0Äê 2. 'Ô!ª 3. Ú%m Ò 5 X A Ý9
4. üÔ¾¨ÎÄÒÔ Ò 5 X B àÊüºÔ¾,#!ª 5. Ú!ªåº¥| SºÔþÄÒÔ 6. 8ÄÒÔJ±,Q¹ÛÚ9Sü OM09389 B A Ò 5. 8ÄÒÔ A. %m B. ÄÒÔ
Page 45 - 8Ú EMI õSÎn
Xøþñ ±,QWÀ
]9x 17 & EMI õ S 1. 8Ú EMI õSÎn
Xøþñ ±,QWÀ 2. ßÝX EMI õS JÙÿÔ+XõS`ÔîÝ+WXõS áU8Ï)@¬ E|< OM09376 A Ò 8. 8 EMI õS A. EMI õS
Page 46 - 8
âXñ Ò 9 X A J±,QW
18 SC5000 ]Û+ & Ç { ª 1. 8
âXñ Ò 9 X A J±,QW 2. åÞK¥F$ Ò 9 X B 3. ߥF$ Ò 9 X C J±,QW 4. Ú{ªåâ¥|JªßW Ò 9 X D OM09390 A C B D Ò 9. 8Ç{ª A. ñ B. åÞK$ C. ªß$ D. Ú{ª¥Î
Page 49 - ¦9J»ûhþñ
]9x 21 ] c 5 ¼ Å Ì a n ! 1. ÚOO|9
2. ¦9J»ûhþñ 3. Ú d`DB²yÛ OM09393 A C B Ò 12. ] 5 ¼ ÅÌan! A. ñ B. DB C. d
Page 54 - ÚøþûÎñ»û
â
26 SC5000 ]Û+ ] c J ª 1. Þ
ªSãUμ! 9áu<X¦Ñ
ªh¹â
G$ 2. å!¥|
ªÈ 3. ÚøþûÎñ»û
â OM09170 Ò 17. ]Jª
Page 55 - ¦9J»û ̄þñ
]9x 27 ] c Ð < 1. £þ^üøþñÎnü
Þ OM09375 Ò 18. ]^ 2. ÚÝÐ<GÈ 3. ªÎÔãXÐ< 4. ÎnÐ<X!B 5. ¦9J»û¯þñ B B B B A OM09377 Ò 19. ÚÐ<În
A. Ð< B. ñ!B 6. ÚJ-Ð<9
