INSTEON 73210 - Manual

Page 1 of 1
Rev. 04-06-2009

Using an INSTEON Device to Trigger a Telephone Alert

1)

Follow Phone Dialer’s User’s Instructions on Installation and Programming (disregard instructions referring to other Skylink products)

2)

Plug your I/O Linc into an un-switched outlet near your Phone Dialer

I/O Linc’s Status LED will turn on

3)

Remove the pre-stripped plastic insulation from included connection wire

4)

Insert one of connection wire’s stripped leads into I/O Linc’s N/C terminal (see Figure 1)

5)

Insert connection wire’s other stripped lead into I/O Linc’s Common terminal (see Figure 1)

6)

Open Phone Dialer’s cover and insert connection wire into Phone Dialer’s N.C. terminals (remove existing metal jumper). Close Phone Dialer’s cover.

Link INSTEON Controller/Sensor to I/O Linc

7)

Press & hold the Set button on the INSTEON device you want to trigger a telephone alert

Controller’s Status LED will begin blinking

8)

Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)

I/O Linc will beep once again to confirm linking; Controller’s LED will stop blinking

Set I/O Linc into Momentary Mode

9)

Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)

10) Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)
11) Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)

I/O Linc’ Status LED will stop blinking

12) Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)
13) Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)
14) Press & hold I/O Linc’s Set button until it beeps (about 3 seconds)

I/O Linc’ Status LED will stop blinking

15) Test by turning your INSTEON Controller/Sensor On or Off

Phone Dialer will call according to its programming in step 1 in response to INSTEON On and Off commands

Introduction

I/O Linc – INSTEON Telephone Alert Kit enhances your INSTEON network by using a
phone dialer along with an I/O Linc to immediately notify you and/or neighbors and loved
ones via telephone and/or cell phone that there is something happening at your home
requiring your attention. Recipients of the automated phone call will hear a user recorded
message identifying the concern. By linking an INSTEON motion sensor, door/window,
and/or leak/flood sensor to the I/O Linc, the phone dialer can call you if any unauthorized
movement, door/window activity or a leak takes place. Any device that transmits an
INSTEON signal can be used to trigger the I/O Linc - INSTEON Telephone Alert Kit to call
out simply by linking the devices together.

Quick-Start Guide

I/O Linc

TM

– INSTEON Telephone Alert Kit

Model: 73210
Telephone Alert of INSTEON Activity

SmartLabs Limited Warranty – SmartLabs warrants to original consumer of this product for a
period of 2 years from date of purchase, this product will be free from defects in material &
workmanship & will perform in substantial conformity with its owner's manual. W arranty shall
not apply to defects caused by misuse or neglect.
U.S. Patent No. 7,345,998, International patents pending ©Copyright 2009
SmartLabs, 16542 Millikan Ave., Irvine, CA 92606, 1-800-SMARTHOME (800-762-7846)

Connection

Wire

Phone Dialer

Power Supply

Set Button / Status LED

Phone Cord

Screw Terminals

Questions?

Click: For Advanced Features and X10 compatibility, refer to I/O Linc’s Owner’s Manual:

http://wiki.smarthome.com/index.php?title=I/O_Linc_-_INSTEON_Low_Voltage_/_Contact_Closure_Interface_Owner%27s_Manual

Call: Friendly tech support @ 1-800-SMARTHOME (800-762-7846)

I/O Linc’s Screw Terminals

5V GND Sense N/C

N/O

Common

5

Volts

Ground

Sensor

Input

Normally

Closed

Normally

Open

Switches

between N/O

and N/C

Items you will Need

1) Wire

stripping

tool

Figure 1

Wiring I/O Linc to Phone Dialer

Connection

Wire

Phone

Dialer

N.C.

Terminals

N/C

/

Common

Terminals

I/O Linc (screwdriver

included)