Ingersoll Rand 231 - Manual

Ingersoll Rand 231

Ingersoll Rand 231 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
Page: / 28

Table of Contents:

  • Page 2 – WARNING LABEL IDENTIFICATION; FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.; ADJUSTMENTS; push the reverse valve
  • Page 3 – PLACING TOOL IN SERVICE; LUBRICATION; Letter
  • Page 4 – DECLARATION OF CONFORMITY; declare under our sole responsibility that the product,; Patrick S. Livingston; Date
  • Page 5 – légères sur camions et matériels agricoles.; ATTENTION; MISE EN SERVICE DE L’OUTIL; NOTE
  • Page 6 – SIGNIFICATION DES ETIQUETTES D’AVERTISSEMENT; RÉGLAGES; REGLAGE DU REGULATEUR DE PUISSANCE; , tourner la soupape d’inversion jusqu’à ce que; pousser la
  • Page 7 – LUBRIFICATION; ou en fonction de l’expérience, injecter environ 4 cm; SPÉCIFICATIONS; pistolet; Position du
  • Page 8 – Clés à chocs à Haute Performance; CERTIFICAT DE CONFORMITÉ; ous; CONSERVEZ SOIGNEUSEMENT CES INSTRUCTIONS. NE PAS LES DÉTRUIRE.
  • Page 9 – BETRIEBSHANDBUCH FüR; Maschinen und Geräte.; ACHTUNG; INBETRIEBNAHME DES WERKZEUGES; HINWEIS
  • Page 10 – ANWEISUNGEN AUF WARNSCHILDERN; EINSTELLUNGEN; EINSTELLUNG DES LEISTUNGSREGLERS; das
  • Page 11 – SCHMIERUNG; Datencode mit
  • Page 12 – KONFORMITÄTSERKLÄRUNG; ir; Datum
  • Page 13 – applicazioni di attrezzatura agricola.; AVVERTENZA; MESSA IN SERVIZIO DELL’ATTREZZO; AVVISO
  • Page 14 – IDENTIFICAZIONE DELLE ETICHETTE DI AVVERTENZA; REGOLAZIONI; IMPOSTAZIONE DEL REGOLATORE DI; Per piena potenza in entrambe le direzioni; valvola d’inversione fino a quando l’intacco su ciascuna; I numeri compresi tra 0 e 5; , spingere la valvola
  • Page 15 – LUBRIFICAZIONE; Impugnatura; Posizione
  • Page 16 – DICHIARAZIONE DI CONFORMITÀ; oi; Data; CONSERVARE QUESTE INSTRUZIONI. NON DISTRUGGERLE.; materiali in modo da poterli riciclare.
  • Page 17 – aplicaciones en camiones ligeros y aperos de labranza.; AVISO; PARA PONER LA HERRAMIENTA EN; NOTA
  • Page 18 – ETIQUETAS DE AVISO; AJUSTES; COLOCACIÓN DE REGULADOR DE; Las Llaves de Impacto Modelos 231 y 231--2 incorporan; empuje hacia adentro la
  • Page 19 – PARA PONER LA HERRAMIENTA EN SERVICIO; LUBRICACIÓN; Ubicación
  • Page 20 – Llaves de Impacto Industriales Ligeras; DECLARACION DE CONFORMIDAD; os abajo firmantes; Fecha
  • Page 21 – SLAGMOERSLEUTELS VOOR ZWAAR WERK; LET WEL; WAARSCHUWING; INGEBRUIKNEMING VAN HET
  • Page 22 – LABELS MET WAARSCHUWINGSINSTRUCTIES; AFSTELLEN; AFSTELLING VAN DE KRACHTREGELAAR; de omkeerhendel; het
  • Page 23 – INGEBRUIKNEMING VAN HET GEREEDSCHAP; DE SMERING; , of zoals de praktijk; SPECIFICATIES; pistool; datumcode
  • Page 24 – Typen 231 en 231- 2 Slagmoersleutels voor Zwaar Gebruik; SCHRIFTELIJKE VERKLARING VAN CONFORMITEIT; ij
  • Page 27 – USA
Loading the manual

Refer All Communications to the Nearest

Ingersoll--Rand Office or Distributor.

Ingersoll--Rand Company 2001

Printed in U.S.A.

03526092

Form P6169
Edition 24
October, 2001

INSTRUCTIONS FOR

MODELS 231 AND 231--2 HEAVY --DUTY

AUTOMOTIVE IMPACT WRENCHES

Model 231 and 231 --2 Impact Wrenches are designed for use in general automotive repair,

body shops, front end service and light truck and farm equipment applications.

Ingersoll --Rand is not responsible for customer modification of tools for applications on

which Ingersoll --Rand was not consulted.

IMPORTANT SAFETY INFORMATION ENCLOSED.

READ THIS MANUAL BEFORE OPERATING TOOL.

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION

IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

PLACING TOOL IN SERVICE

•

Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.

•

For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8” (10 mm) inside diameter air supply
hose.

•

Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.

•

Do not use damaged, frayed or deteriorated air
hoses and fittings.

•

Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905--1 for a
typical piping arrangement.

•

Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.

•

Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.

•

Do not remove any labels. Replace any damaged
label.

USING THE TOOL

•

Always wear eye protection when operating or
performing maintenance on this tool.

•

Always wear hearing protection when operating
this tool.

•

Keep hands, loose clothing, long hair and jewelry
away from working end of tool.

•

Note the position of the reversing lever before
operating the tool so as to be aware of the direction
of rotation when operating the throttle.

•

Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.

•

Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.

•

Tool shaft may continue to rotate briefly after
throttle is released.

•

Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.

•

Use accessories recommended by Ingersoll--Rand.

•

Use only impact sockets and accessories. Do not
use hand (chrome) sockets or accessories.

•

Impact wrenches are not torque wrenches.
Connections requiring specific torque must be
checked with a torque meter after fitting with an
impact wrench.

•

This tool is not designed for working in explosive
atmospheres.

•

This tool is not insulated against electric shock.

•

Prevent exposure and breathing of harmful dust
and particles created by power tool use:

Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

-- lead from lead based paints,
-- crystalline silica from bricks and cement

and other masonry products, and

-- arsenic and chromium from chemically

treated lumber.

Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.

The use of other than genuine Ingersoll--Rand replacement parts may result in safety hazards, decreased tool

performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll--Rand Authorized

Servicenter.

GB

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - WARNING LABEL IDENTIFICATION; FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.; ADJUSTMENTS; push the reverse valve

2 WARNING LABEL IDENTIFICATION FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Always wear eye protection when operating or perform- ing maintenance on this tool. WARNING WARNING Always wear hearing protection when operating this tool. Always turn off the air sup- ply and disconnec...

Page 3 - PLACING TOOL IN SERVICE; LUBRICATION; Letter

3 PLACING TOOL IN SERVICE LUBRICATION Ingersoll--Rand No. 50 Ingersoll--Rand No. 100 Always use of an air line lubricator. We recommend thefollowing Filter--Lubricator--Regulator Unit: For International-- No. C28--C4--FKG0 For USA -- No. C28--04--FKG0--28 After each forty--eight hours of operation, ...

Page 4 - DECLARATION OF CONFORMITY; declare under our sole responsibility that the product,; Patrick S. Livingston; Date

Ingersoll - Rand, Co. ISO8662 (1994 → ) XUA XXXXX → Models 231 and 231- 2 Impact Wrenches 98/37/EC 78192 Trappes Cedex France October, 2001 October, 2001 4 DECLARATION OF CONFORMITY W e (supplier’s name) (address) declare under our sole responsibility that the product, to which this declaration rela...

Other Ingersoll Rand Models