Impex SM-4008 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; Thank you for selecting the MARCY; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................……………. 1 IMPORTANT SAFETY NOTICES.................................................................… 2 SMITH MACHINE HARDWARE PACK….......…............................................. 4 SMITH MACHINE ...

Page 3 - IMPORTANT SAFETY NOTICE; WARNING LABEL PLACEMENT

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 6 - SMITH MACHINE HARDWARE PACK

SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5

Page 9 - SMITH MACHINE ASSEMBLY INSTRUCTION; DIAGRAM 1

SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to ...

Page 10 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Guide Rod (#24) into the hole on left Base Frame (#5). Secure it with one M8 x 2 3/8” Allen Bolt (#103), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut (#109). Slide the Left Lower Safety Stop Fr...

Page 12 - DIAGRAM 3

A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear Base Frame (#8). C.) Attach the Lower Pulley Frame (#16) to the Middle Vertical Frame from rear. Attach the Foot Plate (#32) to the Middle Vertical F...

Page 14 - DIAGRAM 4

M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). B.) Attach the Butterfly Stopper (#31) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts (#58). C.) Attach the Backrest Board (#39) to Middle Vertical Frame. Secure it with two M8 x 2 3/8” Allen Bol...

Page 15 - DIAGRAM 5

(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install the Left Butterfly (#12). B.) Insert two Swivel Pulley Brackets (#15) into the holes on the Butterfly Pulley Bracket (#14). Secure each Swivel Pulley Bracket with one M12 x 5” Hex Bolt (#100), two Ø 1” Wash...

Page 23 - DIAGRAM 8

Page 25 - DIAGRAM 9

Page 28 - SMITH MACHINE PARTS LIST

SMITH MACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Front Left Vertical Frame 1 61 1 ½” Square End Cap 1 2 Front Right Vertical Frame 1 62 Pulley 20 3 Rear Left Vertical Frame 1 63 Small Pulley 4 4 Rear Right Vertical Frame 1 64 Butterfly Arm Foam Roll 2 5 Base Frame 2 65 1 ¾” Square End Cap 5 6 Rea...

Page 29 - MULTI-PURPOSE BENCH HARDWARE PACK

MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 28

Page 31 - ASSEMBLY INSTRUCTION

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts unt...

Page 36 - MULTI-PURPOSE BENCH PARTS LIST

34 MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Post 1 3 Rear Stabilizer 1 4 Seat Bracket 2 5 Leg Developer 1 6 Leg Developer Weight Post 1 7 Backrest Support 2 8 Incline Support 1 9 Front Stabilizer 1 10 Seat Pad 1 11 Backrest Board 1 12 5/8” x 1 1/8” End Cap 4 13 ...

Page 37 - SM-4008 WEIGHT RESISTANCE CHART; Station Ratio; Low Pulley

SM-4008 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 100% 10 lb. plate creates 10 lb. resistance Butterfly (both arms) 100% 10 lb. plate creates 5 lb. resistance Left Cross-Over 50% 10 lb. plate creates 5 lb resistance Right Cross-Over 50% 10 lb. plate creates 5 lb resistance *Numbers ar...

Page 38 - LIMITED WARRANTY

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IM...

Impex SM-4008 - Manual

Table of Contents:

Summary

Other Impex Models