Page 2 - EXPLANATION OF SYMBOLS; Symbols
2 – English EXPLANATION OF SYMBOLS Symbols WARNING! The edger can bedangerous!Careless or incorrect use can resultin serious or fatal injury to theoperator or others. Always use:• A protective helmet where there is a risk of falling objects. • Ear protection• Approved eye protection Read through the...
Page 3 - List of contents; CONTENTS
English – 3 List of contents SYMBOL EXPLANATION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS Personal protective equipment ..................
Page 4 - SAFETY INSTRUCTIONS; Personal protective equipment; The machine’s safety equipment
4 – English SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT INFORMATION • An edger used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury tothe operator or others. It is extremely important thatyou read and understand the content of this manual...
Page 6 - Throttle trigger lock
6 – English SAFETY INSTRUCTIONS IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine’s safety equipment. If the machine does not meet any of thecontrols listed below you should contact yourservice workshop. • The purchase o...
Page 8 - General safety instructions; Safety instructions before starting work
8 – English General safety instructions SAFETY INSTRUCTIONS IMPORTANT INFORMATION • The machine is only designed for cutting the edges of lawns. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommendin the chapter “Technical data”. • The operator ...
Page 9 - Transport and storage
English – 9 SAFETY INSTRUCTIONS Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or nakedflames. For example, electric machines, electric motors,electrical switches/power switches, heaters or the like. • When st...
Page 10 - General working instructions; Basic safety precautions; Basic working techniques; Safety instructions while working
10 – English SAFETY INSTRUCTIONS General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the edger. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contactyour dealer or your service work...
Page 11 - Safety instructions after completing work
English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning,carrying out repairs or aninspection. Remove the sparkplug cable from the sparkplug. • Wear heavy-duty gloves when carrying out repairs onthe edger. • Store the machine out of re...
Page 12 - What is what on the edger?
12 – English WHAT IS WHAT? What is what on the edger? 1. Blade 2. Grease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air filter cover 16. Clutch ...
Page 13 - Assembling the blade; ASSEMBLY; Assembling the loop handlebar
English – 13 Assembling the blade Fit the blade as follows: 1. Fit the drive disc (A) on theoutgoing shaft. Make surethat the edge that fits inthe hole of the blade isfacing outward. 2. Block the blade rotation byinserting locking pin in thehole behind the bladeguard engaging it in thecorresponding ...
Page 14 - FUEL HANDLING; Fuel mixture; Mixture
14 – English NOTE!The edger is fitted with two-stroke engines and must always berun on a mixture of gasoline and two-stroke oil. To ensure thecorrect mixture proportions it is important to measure thequantity of oil accurately. When mixing small amounts of fuelsmall discrepancies in the amount of oi...
Page 15 - Control before starting; START AND STOP; Start and stop
English – 15 Control before starting WARNING!When the engine starts with the choke lever inthe choke or starter throttle position thecutting tool (blade or trimmer) starts to rotateimmediately. START AND STOP For reasons of safety followthese recommendations! • Check that the support flange is not c...
Page 16 - Basic setting; MAINTENANCE; Carburetor; Operation; Conditions
16 – English Basic setting • The carburetor is set to its basic setting when test run at the factory. The basic setting should be kept during the machine‘sfirst working hours. Thereafter the carburetor should be finelyadjusted. Fine adjustment should be carried out by a skilledtechnician. NOTE! If t...
Page 17 - Correctly adjusted carburetor; Final setting of the idling speed T
English – 17 Correctly adjusted carburetor A correctly adjusted carburetor means that the machineaccelerates without hesitation and the machine 4-cycles a littleat max speed. Furthermore, the cutting attachment must notrotate/move at idling. A too lean adjusted low speed needle Lmay cause starting d...
Page 18 - Muffler with catalytic converter; Cooling system
18 – English A muffler fitted with a catalytic converter reduces the extent ofthe following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways.• Aldehydes. The most common f...
Page 19 - Lubricating the flexible drive axle; Air filter; Angle gear
English – 19 Lubricating the flexible drive axle Adjusting the edger‘s cutting depth MAINTENANCE Inside the edger‘s drive shaftis a flexible drive axle. Theflexible drive axle should beregularly lubricated after 30hours of operation. Loosenthe two screws on the anglegear and remove it. Theflexible d...
Page 20 - Maintenance schedule; Daily maintenance
20 – English NOTE: Use only HUSQVARNA replacement parts. Use of otherbrands of replacement parts can cause damage to your unit orinjury to the operator or others. Your warranty does not coverdamage or liability caused by the use of accessories and/orattachments not specifically recommended by HUSQVA...
Page 21 - TECHNICAL DATA; Technical data
English – 21 TECHNICAL DATA Technical data Engine Displacement, cu. in/cm 3 Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling speed, rpmSpeed of output shaft, rpmMax. engine output, acc. to ISO 8893Catalytic converter mufflerSpeed-regulated ignition system Ignition system...
Page 22 - EMISSION CONTROL WARRANTY STATEMENT; YOUR WARRANTY RIGHTS AND
22 – English ´+H#=¶54¨ EMISSION CONTROL WARRANTY STATEMENT WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTSRepair or replacement of any warranted part will be perfor-med at no charge to the owner at an approved HusqvarnaForest & Garden servicing dealer. If you have anyquestions regarding your warr...
Page 23 - NOTES
