Husqvarna 323C - Manual

English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimise vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. The machine ′ s vibra...

6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′ s safety equipment Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released. • Press the throttle lock and make sure it returns to its original position when you r...

English – 7 SAFETY INSTRUCTIONS • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage. Never use a ...

8 – English SAFETY INSTRUCTIONS Cutting equipment Trimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the recommended c...

English – 9 SAFETY INSTRUCTIONS (CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord. Never wrap the starter cord around your hand Fuel safety • Always use a fuel container with an anti-spill valve. • Never refuel the machine while the engine is ...

10 – English SAFETY INSTRUCTIONS Basic working techniques • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass trimming using a trimmer head and plastic blades Trimming • Hold the tr...

12 – English ASSEMBLY Fitting the loop handle (323C, 325Cx) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (323L, 325Lx, 325LD...

14 – English ASSEMBLY Fitting the trimmer guard and trimmer head (323C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. • Hold the dust cup with a spanner to prevent the shaft from rota...

English – 15 FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing sm...

16 – English FUEL HANDLING Fuelling • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not smo...

English – 17 STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

18 – English STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position. Air purge: Press the air purge diaphragm repeatedly unti...

English – 19 MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaus...

20 – English MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting at...

English – 21 MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the cyl...

22 – English MAINTENANCE Oiling the air filter Always use HUSQVARNA filter oil, art. no. 503 47 73-01. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic ...

English – 23 TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

26 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

1 Tri Cut 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10

1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"

1 Trimmy Hit 2 3 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6

1 Trimmy Hit Junior 2 5 6 7 8 9 10 12 “Click” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6"

1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 1 2 3 4 5 6 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 11" Trimmy VII