Huffy 89025 - Manual
Huffy 89025 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Display Stand - Top View
- Page 3 – Assemble rims as shown below.; RIM ASSEMBLY - Corner Locations 1 and 2
- Page 4 – CLIP “ARM”
- Page 5 – NET INSTALLATION
- Page 7 – ELEVATOR ASSEMBLY - Corner Locations 1 and 3
- Page 9 – Two people are recommended for
- Page 10 – Insert handle assembly through pole mount; 4” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3; Attach adjustment rod (47) to lower elevator
- Page 12 – Two people
- Page 13 – HEIGHT ADJUSTMENT
- Page 14 – 4” FAN MOLDED PLASTIC BOARD ELEVATOR ASSEMBLY - Corner Location 2
- Page 19 – WARNING
- Page 20 – 0” FAN BACKBOARD ASSEMBLY - Corner Location 4.
- Page 21 – PARTS LIST - See Hardware Identifier
- Page 22 – PLASTIC SPACERS
1
06/03
P/N 211543B
Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
IMPORTANT!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although
great care and effort have been taken, problems may occur. To ensure prompt and correct handling of any problems, or to answer any
questions, please contact the Sample and Display Technician at 414-820-3440.
REQUIRED TOOLS AND
MATERIALS:
• 2 People
• Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4”
or Pliers
• Phillips Screwdriver
• 2 Step Ladders, 8 ft. (2.4 m)
Model 89025
Please refer to modular category #350 when arranging product for modular display.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
•
During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
•
If technical assistance is required, contact Huffy Sports’ Sample
and Display Technician.
•
Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
•
Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
•
All instructions and warnings MUST accompany any display item
that is sold.
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
Internet Address:
http://www.huffysports.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
P/N 211543B 06/03 2 Install display boards in the marked locations. Each mounting location consists of a mounting polestub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicatedirection the board is facing). Corner “2” 73603 Corner “4” 62959 Corner “3” 88603 Corne...
3 06/03 P/N 211543B 2 3 4 8 7 Assemble rims as shown below. 1 3. 5. 4. RIM ASSEMBLY - Corner Locations 1 and 2
P/N 211543B 06/03 4 6. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Besure to follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” o...
