Huffy 89025 - Manuals

Huffy 89025 – Manual in PDF format online.

Manuals:

Manual

Manual Huffy 89025

Summary

Page 2 - Display Stand - Top View

P/N 211543B 06/03 2 Install display boards in the marked locations. Each mounting location consists of a mounting polestub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicatedirection the board is facing). Corner “2” 73603 Corner “4” 62959 Corner “3” 88603 Corne...

Page 3 - Assemble rims as shown below.; RIM ASSEMBLY - Corner Locations 1 and 2

3 06/03 P/N 211543B 2 3 4 8 7 Assemble rims as shown below. 1 3. 5. 4. RIM ASSEMBLY - Corner Locations 1 and 2

Page 4 - CLIP “ARM”

P/N 211543B 06/03 4 6. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Besure to follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” o...

Page 5 - NET INSTALLATION

5 06/03 P/N 211543B Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 7. 58 9 10

Page 7 - ELEVATOR ASSEMBLY - Corner Locations 1 and 3

7 06/03 P/N 211543B 8 11 49 16 10. 11. 17 30 24 52 51 49 30 12. 49 8 55 54 54 57 44 57 55 13. 48 8 46 45 26 47 25 Install pole mount bracket (49) withcarriage bolts (16) as shown.Tighten flange nuts (8) completely. Attach spacers (51, 52) to pole mount bracket(49) with bolts (24), washers (30), and ...

Page 9 - Two people are recommended for

9 06/03 P/N 211543B 17. 16. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard supportbrackets (37) using spacers (59), bolt (27), and nut (42)as shown. Attach backboard assembly to pole section (11). Installpole cap (43). NOTE: Two people are recommended for this step. Use caution; ...

Page 10 - Insert handle assembly through pole mount; 4” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3; Attach adjustment rod (47) to lower elevator

P/N 211543B 06/03 10 19. 55 18. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place atthe 10’ (3.05m) mark with pin (55). 23 23 17 65 15 15 24 18 20. 44” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3 Attach adjustment rod (47) to lower elevator tubes (29)...

Page 12 - Two people

P/N 211543B 06/03 12 27 21 42 21 22 22 23. 42 21 21 27 27 29 42 43 24. Attach backboard assembly to pole section (11). Then install pole cap (43). NOTE: Two people are recommended for this step. Use caution;elevator assembly is heavy. Attach upper elevator tubes (21) to backboard brackets (23) using...

Page 13 - HEIGHT ADJUSTMENT

13 06/03 P/N 211543B 42 27 29 29 47 59 59 26. Insert handle assembly through pole mount assembly as shown. Lock pole assembly inplace at the 10’ (3.05m) mark with pin (55). 55 A C B To Set Backboard Height:A. While holding handle, remove pin (55). B. Move elevator up or down to desired height. C. Re...

Page 14 - 4” FAN MOLDED PLASTIC BOARD ELEVATOR ASSEMBLY - Corner Location 2

P/N 211543B 06/03 14 1. Attach elevator bracket (36)and reinforcement bracket (41)to pole section (11) using bolts(16) and nuts (8) as shown. 41 11 36 16 8 23 23 17 65 15 15 24 18 2. 44” FAN MOLDED PLASTIC BOARD ELEVATOR ASSEMBLY - Corner Location 2 Assemble backboard brackets (23) using spacers (15...

Page 19 - WARNING

19 06/03 P/N 211543B 27 59 59 6 42 61 61 61 61 61 9. 10. 11. 64 63 36 62 62 6 29 Attach adjustment tube to lower elevator tubesusing bolt spacers and nut as shown. Finish handle assembly byattaching right handle using screwsas shown. Insert lower adjustment rod (62) into bottom of adjustment tube (6...

Page 20 - 0” FAN BACKBOARD ASSEMBLY - Corner Location 4.

P/N 211543B 06/03 20 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble 40” fan backboard as shown below with a standard rim as shown. 40” FAN BACKBOARD ASSEMBLY - Corner Location 4. 35 32 33 8 7 7 35 12. 34 8

Page 21 - PARTS LIST - See Hardware Identifier

21 06/03 P/N 211543B Item #26 (2) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 1 200215 Cross Pin 6 1 900006 Adjustment Tube - Upper 7 16* 203113 Bolt, Hex-Flange 5/16-18 x 2.5 8 34 203100 Nut, Hex-Flange 5/16-18 whiz Loc...

Page 22 - PLASTIC SPACERS

P/N 211543B 06/03 22 Item #27 (13) Item #18 (2) Item #20 (2) Item #33 (24) Item #35 (6) 22 of 22 Item #30 (8) Item #39 (4)* Item #40 (2) Item #59 (8) Item #60 (2) HARDWARE IDENTIFIER (BOLTS & SCREWS) HARDWARE IDENTIFIER (SPRINGS & WASHERS) Item #16 (4) Item #22 (4) Item #63 (1) PLASTIC SPACE...