HP v75 - Manual

2 Safety and Maintenance Guidelines Safety Guidelines Power Requirements A power cord is included with your monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with your monitor, refer to the “Pow...

Safety and Maintenance Guidelines Ä CAUTION: For the protection of your monitor, as well as your computer, connect all power cords for your computer and its peripheral devices (such as a monitor, printer, scanner) to some form of surge protection device such as a power strip or Uninterruptible Power...

3 Setting Up the Monitor Attaching the Monitor Base 1. Carefully position the monitor bottom side up. 2. Align the hooks on the base with the sockets on the bottom of the monitor and attach the base. 3. Push the base toward the front of the monitor until it stops. User Guide 3–1

Setting Up the Monitor Removing the Monitor Base In the event that you need to disassemble the base from the monitor, position the monitor bottom side up and follow these instructions: 1. If you must remove the base attachment, release the catch and slide the base toward the back of the monitor. 2. ...

Setting Up the Monitor Connecting the Speakers (Available with Select Models) Several speaker models are available with select monitors. Refer to the steps below for the speaker model included with your monitor. Tall Speakers with Base 1. If the speakers and bases are not assembled, attach them by t...

Setting Up the Monitor Short Speakers 1. Place the speaker set near the monitor so that the speaker with the controls is on the right side when you view the monitor from the front. 2. Attach the speaker power adapter cable to the black connector on the back of the control speaker, then connect the A...

Setting Up the Monitor USB Speakers 1. Place the speaker set near the monitor so that the speaker with the controls is on the right side when you view the monitor from the front. 2. Plug the USB cable 1 on the control speaker into a USB port on the computer. 3. If available, plug the green connector...

4 Operating the Monitor Software and Utilities Select monitor models will include a CD that contains two files you can install on your computer: ■ an .INF (Information) file ■ an .ICM (Image Color Matching) file Adobe Acrobat Reader is supplied on this CD and can be installed from the menu. ✎ If the...

Operating the Monitor work through separate BNC type connectors or through distribution buffers/boxes. You may need to install the .INF file if these conditions are not met. The Image Color Matching File The .ICM file provides accurate color representation. The .ICM files are data files that are use...

Operating the Monitor 6. Ensure that the proper resolution and refresh rates appear in the Windows Display control panel. ✎ You may need to install the digitally signed monitor .INF and .ICM files manually from the CD in the event of an installation error. Refer to the INF and ICM Readme file on the...

1 2 3 4 Operating the Monitor Front Panel Controls Item Icon Name Function menu menu Launches on-screen displays and exits the menus and On-Screen Display. Left Adjustment Moves backward through menu options or decreases adjustment levels. Right Adjustment Moves forward through menu options or incre...

Operating the Monitor On-Screen Display The On-Screen Display (OSD) adjusts the screen image based on your viewing preferences. To access the OSD, do the following: 1. If the monitor is not already on, press the power button to turn on the monitor. 2. Press the menu button to display the On-Screen D...

Operating the Monitor 5. The adjustment window displays. Press the Right-Adjustment or Left-Adjustment buttons to increase (Right) or decrease (Left) the level of adjustment. 6. Press select to save the new adjustment. 7. To exit the On-Screen Display, press the menu button once. On-Screen Display F...

Operating the Monitor Monitor Messages No Signal Message If a No Signal message displays on the monitor screen, check to be sure the video cable is properly connected and ensure that the computer is powered on. 4–8 User Guide

Operating the Monitor Out of Frequency Range Message If an Out of Frequency Range message displays on the monitor screen, the video resolution and/or refresh rate are set higher than the levels the monitor supports. To change the video resolution or refresh rate on the monitor: 1. Restart the comput...

Operating the Monitor Using the Energy Saver Mode The monitor is designed to meet requirements for reduced power consumption. Using a combination of hardware and software functions, this energy-saving feature allows the computer to control the monitor’s power consumption and reduce the monitor’s pow...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power switch is off. Turn on power. Video cab...

B Technical Specifications ✎ All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP’s component manufacturers’ typical level specifications for performance and actual performance may vary either higher or l...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res...

Agency Regulatory Notices Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made wit...

Agency Regulatory Notices To identify this product, refer to the Part, Series, or Model number found on the product. Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B r...

Agency Regulatory Notices Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste eq...

Agency Regulatory Notices Korean Notice Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100-120V or 200-240V. The power cord set (flexible cord or wall plug) received with the m...

Agency Regulatory Notices Japanese Power Cord Requirements For use in Japan, use only the power cord received with this product. Ä CAUTION: Do not use the power cord received with this product on any other products. C–6 User Guide