Page 2 - Notice
ii Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose . Hewlett-Packard shall ...
Page 3 - Contents
iii Contents 1 Specifications ......................................................................................................................................... 7 Technical Specifications.............................................................................................................
Page 7 - Specifications; Technical Specifications; Environmental
7 1 Specifications Technical Specifications The specifications listed below for HP Tower Server tc2100 may vary if you install a mass storage device in your server that has more stringent environmental limits. Ensure the operating environment for your server is suitable for all of the mass storage d...
Page 8 - Hardware Specifications; Video Display Modes
Chapter 1 Specifications 8 Hardware Specifications Specification Characteristics Processors This HP Server supports Intel Celeron or Intel Pentium III processors (system board automatically detects processor FSB and changes accordingly): Intel Celeron - 850 MHz and above with 100 MHz FSB and Integra...
Page 9 - System Board Layout
Chapter 1 Specifications 9 System Board Layout DIMM Slots FDD IDE-2 IDE-1 Front PanelDisplay Header CMOSClear Jumper Battery ConnectorChassis Fan Video (L) Com 1 (L) Com 2 Parallel (U) Mouse (U) Keyboard (L) 2 USB (L) LAN (U) ConnectorHeatsink Fan Power Processor, Heatsink& Fan 1 2 PCI Slot P5 3...
Page 11 - Front Panel Control and Indicators; Steady green
11 2 Controls, Ports, and Indicators Front Panel Control and Indicators The HP Tower Server tc2100’s controls, indicators, and user-serviceable internal components are shown in the following illustrations. Flexible DiskDrive (FDD) Backup TapeDrive (Optional) 3rd Hard Drive(Optional) CD-ROM Drive Pow...
Page 12 - Flickering green; Additional Front Panel Controls and Indicators; Eject Button; NOTE
Chapter 2 Controls, Ports, and Indicators 12 LAN Activity LED Flickering green LED during any embedded LAN activity. Off when there is no embedded LAN activity. Additional Front Panel Controls and Indicators The Mass Storage devices have additional controls and indicators providing the user with ext...
Page 13 - Rear Panel Ports and Features
Chapter 2 Controls, Ports, and Indicators 13 Rear Panel Ports and Features The following text and illustration describe the ports, switches, and unique features on the Server's rear panel. Power Mouse Keyboard USB (2) LAN COM 2 Parallel Keylock Video COM 1 SystemFan InputVoltage Switch External SCSI...
Page 14 - Applying Power to the HP Server; Powering-Up the HP Server; Powering-Down the HP Server
Chapter 2 Controls, Ports, and Indicators 14 • The LAN port is included as an embedded controller based on Intel's 82559 10/100 BaseT Fast Ethernet Controller. It has a RJ-45 LAN connector on the rear panel. The LED on the front panel is used to indicate LAN activity. • System Fan is a variable spee...
Page 15 - Multiple-Server Configurations
Chapter 2 Controls, Ports, and Indicators 15 NOTE The power supply will continue to provide standby current to the Server until the power cable is disconnected from the rear panel. Multiple-Server Configurations The HP Server temporarily draws a large "inrush current," when first connected t...
Page 16 - CAUTION
Chapter 2 Controls, Ports, and Indicators 16 CAUTION If the power button override is used; there is a strong possibility of corrupted or lost data. Refer to the BIOS Setup Utility in Chapter 8, “Configuring the HP Server” and your NOS documentation for instructions on setting up Sleep States and tra...
Page 17 - Serial Port Connector
17 3 Connector Pinouts Unless otherwise noted, the following features apply to all models. Some features are factory installed; others are optional. Mini-DIN (PS/2) Connectors 1 2 5 6 4 3 Mini-DIN Connector (female) for the Mouse and Keyboard Mini-DIN Connector Pinouts for the Mouse and Keyboard Pin...
Page 18 - Parallel Port Connector
Chapter 3 Connector Pinouts 18 Parallel Port Connector 1 23 45678 9 10111213 14 15 161718 1920 2122232425 Parallel Connector Parallel Port Connector (female) Pinouts Pin Number Signal Description Pin Number Signal Description 1 Strobe5 10 Acknowledgeb 2 Data bit 06 11 Busy 3 Data bit 1a 12 Paper end...
Page 19 - USB Connector; Video Connector
Chapter 3 Connector Pinouts 19 USB Connector 1 1 2 2 3 3 4 4 USB Connector Universal Serial Bus Connector Pinouts Pin Number Signal Description 1 VBUS 2 D+ 3 D- 4 GND NOTE Use of the USB port is supported for printers, scanners, and external modems. Video Connector The embedded video uses the standa...
Page 20 - Shown as pin matching
Chapter 3 Connector Pinouts 20 68-Pin LVD SCSI Port Connector (Low Voltage Differential) Pin 1 Pin 68 LVD SCSI Connector (Male) 68-Pin SCSI Port Connector Shown as pin matching Pin Number Signal Description Pin Number Signal Description 1 +DB(12) 35 -DB(12) 2 +DB(13) 36 -DB(13) 3 +DB(14) 37 -DB(14) ...
Page 21 - 0-Pin Narrow SCSI Port Connector – Accessory Board; Position 1; LAN Connector – Accessory Board
Chapter 3 Connector Pinouts 21 50-Pin Narrow SCSI Port Connector – Accessory Board Position 25 Position 1 Position 26 Position 50 SCSI Port Connector 50-Pin Narrow SCSI Port Connector Pinouts Pin Number Signal Description Pin Number Signal Description 1-11 Ground 37 Reserved 12 Reserved 38 Termpwr 1...
Page 23 - Introduction; Mass Storage Guidelines
23 4 Maintenance Guidelines Introduction This chapter provides the HP Tower Server tc2100’s maintenance guidelines when removing or replacing the mass storage devices, DIMM memory, accessory boards, and processors. Mass Storage The HP Server tc2100 comes standard with one IDE CD-ROM and one flexible...
Page 24 - Boot Priority; IDE Model Boot Order:; SCSI Model Boot Order:
Chapter 4 Maintenance Guidelines 24 o Use only HP Ultra-160 SCSI LVD (1-inch) low profile 3.5-inch hard disk drives for the removable hard disk drive cage. o Only use an HP Ultra-160 SCSI LVD drive as the optional third drive. o The optional HP backup tape drive comes with a 50-to-68-pin adapter to ...
Page 25 - IDE Mass Storage Devices; IDE Controller Configuration; SCSI Mass Storage Devices; SCSI Controller Configuration
Chapter 4 Maintenance Guidelines 25 IDE Mass Storage Devices This section provides the configuration of the IDE mass storage devices, if you have selected an IDE version of the HP Server tc2100. IDE Controller Configuration The embedded IDE controller is available for both models (IDE or SCSI) of th...
Page 27 - SCSI Mass Storage Additions; External SCSI Connector; Memory Guidelines
Chapter 4 Maintenance Guidelines 27 SCSI Mass Storage Additions The table below lists the number and types of mass storage devices in or may added into the SCSI model of the HP Server. SCSI Model Mass Storage Devices Interface Types Max No. Devices Installed Devices and Addresses FDD 1 Factory insta...
Page 28 - Accessory Board Guidelines; Tested PCI Boards; IRQ Settings; Processor Guidelines
Chapter 4 Maintenance Guidelines 28 http://www.hp.com/go/Server • HP Customer Service The video memory is limited to 4 MB on the system board and cannot be upgraded. Accessory Board Guidelines The system board in the HP Server tc2100 provides up to five 32-bit PCI slots (P1 through P5). Tested PCI B...
Page 31 - Beep Codes for Fatal Errors
31 5 Error Messages Introduction This chapter describes the beep codes and the POST error codes that may occur during the boot process or normal operation of the HP Tower Server tc2100. Beep Codes If the POST routines cannot display messages when an error occurs before the video display is initializ...
Page 36 - To prevent unstable behavior
Chapter 5 Error Messages 36 Code Description (System Monitor Errors) Problem/Solution 0A01 Emergency shutdown occurred (system initiated) The Server has performed an emergency shutdown to prevent damage to system board. • To prevent unstable behavior , or a system hang during the boot process, do no...
Page 37 - Diagnostics; Diagnostic Tests; Diagnostics Description; WARNING; HP DiagTools
37 6 Diagnostics Diagnostic Tests When the Server boots, a series of tests are displayed on the screen. The number of tests displayed depends on the configuration of the Server. The following are the types of errors a user might get with the HP Server. • Built-in diagnostic Error Messages. • BIOS an...
Page 38 - About Error Messages; Advantages and Limitations of Hardware Diagnostics; Some limitations are:
Chapter 6 Diagnostics 38 The HP DiagTools Utility is run from the Startup CD-ROM, which is a bootable CD-ROM when inserted into the CD-ROM drive and the Server is rebooted. A basic suite of tools checks key Server components, and a menu of advanced tests is available for in-depth testing. DiagTools ...
Page 41 - Maintenance and Troubleshooting; Preventive Maintenance Procedures; Troubleshooting; Troubleshooting Checklist
41 7 Maintenance and Troubleshooting Preventive Maintenance Procedures Refer to the following table for preventive maintenance procedures used for the HP Tower Server tc2100. Be sure to turn off power to the Server when cleaning it. Preventative Maintenance Procedures Component Time Frame Maintenanc...
Page 42 - Server Does Not Power On
Chapter 7 Maintenance and Troubleshooting 42 • Remove all options added since the Server was received and then add one option, and only one option, at a time. NOTE If the Server has a large amount of memory installed, it may take 30 seconds for the first screen to display. If it is a hardware error,...
Page 43 - Server Powers On, but Fails POST; BIOS Recovery
Chapter 7 Maintenance and Troubleshooting 43 Refer to “Processor Problems” later in the chapter. Server Powers On, but Fails POST Do one of the following: • If the Server fails POST and an error message appears, refer to Chapter 5, "Error Messages.” • If the suggested solutions do not solve the ...
Page 44 - BIOS Reset; BIOS Update; Password Problems; Clearing the BIOS Configuration
Chapter 7 Maintenance and Troubleshooting 44 BIOS Reset If you need to reset your BIOS settings to the factory defaults (the HP recommended values) due to possible corruptions, perform the following steps. The default values have been selected to optimize the HP Server’s performance. 1. Reboot the S...
Page 45 - Battery; Normal; Resetting a Lost Password; General Server Problems; No lights are on and no error message appears
Chapter 7 Maintenance and Troubleshooting 45 1. Turn off power to the Server and remove the left side cover. 2. Move the jumper from its “Normal” position (Pins 1 & 2) on the system board to the “Clear CMOS” position (Pins 2 & 3) and leave it there for five seconds as shown in the figures be...
Page 46 - Operating system or an application is not responding properly; POST
Chapter 7 Maintenance and Troubleshooting 46 1. Verify the power is good and available. 2. Ensure the Server is turned on (the power-on light should be green and the fans should be on). 3. Turn the Server off and unplug the power cord. a. Wait 30 seconds and plug the power cord back in. b. Turn the ...
Page 47 - Power Problems
Chapter 7 Maintenance and Troubleshooting 47 NOTE The POST error messages may reflect which modules are defective and should be replaced. 2. Review the Troubleshooting Checklist before you continue. 3. Power the Server off and on (instead of using Ctrl-Alt-Del). Powering the server off and on is a m...
Page 48 - Video/Monitor Problems
Chapter 7 Maintenance and Troubleshooting 48 Typically, all fans run when power is turned on and all fans are off when the power is turned off. 5. With the power supply connected to the system board, check the power supply's voltages. 6. If voltages are not present: a. Turn off AC power. b. Disconne...
Page 50 - Configuration Problems
Chapter 7 Maintenance and Troubleshooting 50 17. If the customer has installed a video board instead of using the embedded video, ensure all jumpers and switches are set properly on the installed video board. Refer to the user manual provided with the video board. 18. If the monitor displays a badly...
Page 51 - Printer/Datacomm Problems
Chapter 7 Maintenance and Troubleshooting 51 Symptom: • The configuration information is frequently lost and the battery is good. If the battery is good and you cannot save system configuration, do the following 1. Review the Troubleshooting Checklist before you continue. BIOS configuration informat...
Page 52 - Keyboard and Mouse Problems
Chapter 7 Maintenance and Troubleshooting 52 Keyboard and Mouse Problems Symptoms: • The keyboard does not work • A character is not displayed when a key is pressed 1. Review the Troubleshooting Checklist before you continue. 2. Ensure the keyboard is not locked. 3. Ensure the keyboard cable connect...
Page 54 - SCSI Problems
Chapter 7 Maintenance and Troubleshooting 54 Symptom: • The CD-ROM drive is not working properly The CD-ROM drive provided with this HP Server (SCSI or IDE models) is IDE CD-ROM. If the CD-ROM drive does not work, do the following: 1. Review the basic IDE installation guidelines to ensure a proper c...
Page 58 - Processor Problems; Memory Problems
Chapter 7 Maintenance and Troubleshooting 58 9. Ensure no SCSI device is set to SCSI address ID = 7. This address ID is the reserved for the SCSI controller. 10. Verify all SCSI devices are low voltage differential (LVD) SCSI devices, and there are no single-ended devices on the bus. 11. Verify the ...
Page 59 - Embedded Network Interface Card Problems
Chapter 7 Maintenance and Troubleshooting 59 c. If the error goes away, add another DIMM and reboot again. d. Continue this process until you have installed all DIMMs or you experience a failure. e. Replace the defective DIMM. 7. Once a suspect part has been found, verify the cause of the problem by...
Page 61 - Parts and Illustrations; Exploded View – Covers and Bezels
61 8 Parts and Illustrations Exploded View – Covers and Bezels 1 2 3 4 5 6 7 8
Page 62 - Exploded View – Mass Storage Devices
Chapter 8 Parts and Illustrations 62 Exploded View – Mass Storage Devices 9 10 11 12 13 14 15 16 17 18 19 20
Page 63 - Exploded View – Chassis Fan, Power Supply, and System Board; Rear View
Chapter 8 Parts and Illustrations 63 Exploded View – Chassis Fan, Power Supply, and System Board Rear View 21 22 23 24 25 26
Page 64 - Exploded View – System Board Components
Chapter 8 Parts and Illustrations 64 Exploded View – System Board Components 27 28 29 30 31 32
Page 65 - Replaceable Parts List
Chapter 8 Parts and Illustrations 65 Replaceable Parts List The items in this list and the corresponding item numbers in the respective Exploded Views apply to both models of the HP Server, except where noted. NOTE The part numbers listed below were available at the time of publication. Part numbers...
Page 66 - Cables and Part Numbers
Chapter 8 Parts and Illustrations 66 Item No. Description Replacement Exchange 24 Slot Cover Latch P4648-63022 25 Chassis Fan (Thermal/BIOS speed controlled) P4648-63007 26 Power Supply, 250 W, (Fan Speed thermally controlled) P4648-63020 27a Celeron Heatsink-fan (included with processor kit) 5185-5...
Page 67 - Power Cords
Chapter 8 Parts and Illustrations 67 Language Part Number Language Part Number Polish D4950-63035 Swedish D4950-63012 Hungarian D4950-63037 UK D4950-63013 Turkish D4950-63035 Czech D4950-63036 Greek D4950-63032 Dutch D4950-63006 Power Cords Country Part Number Country Part Number Australia/New Zeala...
Page 69 - Procedures; Safety Information; Service Tools Required; Covers; Removing the Left Side Cover
69 9 Remove/Replace Procedures Introduction This chapter describes the removal and replacement procedures for the user serviceable components in the HP Tower Server tc2100. Safety Information Follow the procedures listed below to ensure safe handling of components and to prevent harm to both you and...
Page 71 - Replacing the Left Side Cover
Chapter 9 Remove/Replace Procedures 71 Removing the Left Side Cover 6. Place the left side cover in a safe place for re-installation later. Replacing the Left Side Cover To replace the left side cover, follow these steps: 1. If you have been installing accessories or servicing the Server, return the...
Page 72 - Hinge Tabs; Alternate Covers; Front Bezels; Removing the Upper Bezel
Chapter 9 Remove/Replace Procedures 72 Hinge Tabs Latch Replacing the Left Side Cover Alternate Covers The other covers (top or right side) used on the Server are not essential when accessing components in or on the Server. However, if for some reason you need to replace one of these covers you can ...
Page 73 - Replacing the Upper Bezel
Chapter 9 Remove/Replace Procedures 73 This action will swing the upper front bezel open on its hinge teeth. 6. Swing the upper bezel completely open and remove it from the front of the Server. Release Tabs (2) Removing the Upper Front Bezel Replacing the Upper Bezel The upper front bezel uses hinge...
Page 74 - Removing the Lower Bezel
Chapter 9 Remove/Replace Procedures 74 Hinge Teeth (4) Replacing the Upper Bezel Removing the Lower Bezel 1. If the Server is operating, power down the Server. Refer to Chapter 2, “Controls, Ports, and Indicators” for instructions. 2. Disconnect the power cord and any external cables connected to th...
Page 75 - Replacing the Lower Bezel; Status Panel Assembly; Removing the Status Panel Assembly
Chapter 9 Remove/Replace Procedures 75 A B C Removing the Lower Bezel Replacing the Lower Bezel 1. If the Server is operating, power down the Server. Refer to Chapter 2, “Controls, Ports, and Indicators” for instructions. 2. Disconnect the power cord and any external cables connected to the Server. ...
Page 76 - Replacing the Status Panel Assembly
Chapter 9 Remove/Replace Procedures 76 2. Disconnect the power cord and any external cables connected to the Server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover. 4. Remove the upper bezel. 5. Remove the lower bezel. 6. Disconnect the status panel connector(s) ...
Page 77 - Mass Storage Devices; Latch Release; Removing the Flexible Disk Drive
Chapter 9 Remove/Replace Procedures 77 8. Restore power to the Server and verify the status panel assembly is working properly. Mass Storage Devices Shelf 5 (2nd Hard Drive) (Optional) Shelf 3 (Backup Tape Drive) (Optional) Shelf 2 (CD-ROM) Shelf 1 (FDD) Latch Release (Drive Cage) Mass Storage Devic...
Page 78 - Replacing the Flexible Disk Drive
Chapter 9 Remove/Replace Procedures 78 A C B Removing the Flexible Disk Drive (FDD) 7. Rotate the FDD mounting assembly off of the flexible disk drive. 8. Place the flexible disk drive in an anti-static bag. Replacing the Flexible Disk Drive 1. If not already mounted, place the two hooks in the scre...
Page 79 - Replacing the CD-ROM
Chapter 9 Remove/Replace Procedures 79 4. Remove the upper bezel. 5. At the rear of the CD-ROM, carefully disconnect the power and data cables. 6. Remove the CD-ROM by: a. Pressing in on both release tabs to release the CD-ROM tray assembly. b. Pull the CD-ROM assembly out of the chassis. c. Remove ...
Page 80 - Removing a Backup Tape Drive; Replacing a Backup Tape Drive
Chapter 9 Remove/Replace Procedures 80 The IDE CD-ROM uses one connector on the cable from the IDE-2 connector, leaving one connector for the optional third hard drive on the IDE model. 7. Replace the upper bezel. 8. Replace the left side cover. 9. Replace the external cables and power cord. 10. Pow...
Page 81 - Removing a Hard Disk Drive (Tray Mounted)
Chapter 9 Remove/Replace Procedures 81 2. Make any settings required by the HP Backup Tape Drive documentation. The SCSI backup tape drive should not be terminated, but if it is remove the termination jumper. The default SCSI address for HP Backup Tape Drive is normally set to ID address = 3. 3. Att...
Page 82 - Replacing a Hard Disk Drive (Tray Mounted)
Chapter 9 Remove/Replace Procedures 82 B A A C Removing Hard Disk Drive (HDD) and Tray Replacing a Hard Disk Drive (Tray Mounted) This procedure is used to replace the third hard disk drive (HDD) mounted in the fourth shelf. The second and third drive trays are identical, but the forth drive tray is...
Page 83 - Removing a Hard Disk Drive (Drive Cage Mounted); Tab Latch
Chapter 9 Remove/Replace Procedures 83 7. Replace the left side cover. 8. Replace the external cables and power cord. 9. Power on the Server as described in Chapter 2, “Controls, Ports, and Indicators.” Removing a Hard Disk Drive (Drive Cage Mounted) The replacement of the mass storage cage mounted ...
Page 84 - Replacing a Hard Disk Drive (Drive Cage Mounted); Mounting tabs
Chapter 9 Remove/Replace Procedures 84 Replacing a Hard Disk Drive (Drive Cage Mounted) 1. If the drive cage is already removed from the chassis, perform the following procedure starting at Step 3. 2. If it is necessary to remove the drive cage from the chassis, perform steps 3 through 6 of the proc...
Page 85 - DIMMs; Removing DIMMs
Chapter 9 Remove/Replace Procedures 85 For the SCSI model, use the SCSI cable, which has 5 connectors and a termination on the end of the cable. Typically, the SCSI cable is already folded, allowing you to use the available connectors on the SCSI cable nearest the drive cage. 9. Connect the power ca...
Page 86 - System Board; Replac
Chapter 9 Remove/Replace Procedures 86 System Board DIMM Slots 1 2 3 Removing DIMMs from System Board Replac i ng DIMMs 1. Choose a DIMM slot for the desired DIMM. DIMM sizes may be mixed on the system board and may be loaded in any order (1 through 3). However, HP recommends starting at slot 1 and ...
Page 87 - DIMM Slot; Removing the Heatsink-Cooling Fan
Chapter 9 Remove/Replace Procedures 87 DIMM Slot Keys Notches Retaining Latches DIMM to Slot Alignment 5. Holding the DIMM at 90 degrees to the system board, press the DIMM fully into the slot until the retaining latches close. If the latches do not close, the DIMM is not inserted correctly. 6. Repe...
Page 88 - Removing the Processor
Chapter 9 Remove/Replace Procedures 88 WARNING The power supply will continue to provide standby current to the HP Server until the power cord is disconnected from the AC power source. 4. Lay the Server on its side (components showing). 5. Disconnect the cooling fan power cable from the connector on...
Page 89 - Replacing the Processor
Chapter 9 Remove/Replace Procedures 89 Pin-1Marker ZIFLever ProcessorSocketBase Removing the Processor 3. Grasp the processor by its edges and lift it out of the processor socket. 4. Place the processor on a static-dissipating work surface or into an anti-static bag. Replacing the Processor 1. Locat...
Page 90 - Replacing the Heatsink-Cooling Fan
Chapter 9 Remove/Replace Procedures 90 Pin-1Marker ZIFLever ProcessorSocketBase Replacing the Heatsink-Cooling Fan Once the processor is installed, the heatsink-cooling fan must be installed on top of the processor. Each processor requires a heatsink, with its cooling fan attached, and a thermal bon...
Page 91 - Method A
Chapter 9 Remove/Replace Procedures 91 Method A a. Position the heatsink over the processor socket and lower it squarely onto the processor, as shown in the following illustration. There are two ridges on the heatsink to help align the heatsink to the processor. The heatsink can only be installed in...
Page 93 - Accessory Boards; Removing Accessory Boards
Chapter 9 Remove/Replace Procedures 93 Accessory Boards Removing Accessory Boards To remove an accessory board, refer to the following procedure. 1. If the Server is operating, power down the Server. Refer to Chapter 2, “Controls, Ports, and Indicators” for instructions. 2. Disconnect the power cord...
Page 94 - Slot Cover Latch; Replacing Accessory Boards
Chapter 9 Remove/Replace Procedures 94 Slot Cover Latch Latch Retainer A. B. C. Removing Slot cover Latch 7. Lift the accessory board up and away from the slot. 8. Place the accessory board and any cables in an anti-static container. Replacing Accessory Boards 1. Read the documentation included with...
Page 96 - Power Supply; Mounting Bracket
Chapter 9 Remove/Replace Procedures 96 Power Supply Removing the Power Supply The low voltage ON/OFF switch on the front panel controls the power supply and the voltage selector switch on the rear panel adapts the power supply to the input AC voltage. To remove the power supply from the chassis, per...
Page 97 - Replacing the Power Supply; Removing the Battery
Chapter 9 Remove/Replace Procedures 97 6. If the power supply is defective and the replacement power supply does not have the mounting bracket, remove the mounting bracket from the defective supply before going to the next procedure. Replacing the Power Supply 1. Place the power supply into the chas...
Page 98 - Replacing the Battery; Chassis Fan; Removing the Chassis Fan
Chapter 9 Remove/Replace Procedures 98 View Rotated90 Degrees CCW Removing the Battery Replacing the Battery 1. Insert the new battery with the positive sign (+) facing out, and ensure that it is seated completely. Ensure the retaining latch is in place, and holds the battery firmly. 2. If necessary...
Page 99 - Replacing the Chassis Fan
Chapter 9 Remove/Replace Procedures 99 2. Disconnect the power cord and any external cables connected to the Server. If necessary, label each one to expedite re-assembly. 3. Disconnect the chassis fan’s power connector from the system board. 4. Remove the fan by placing a sharp flat object (screwdri...
Page 100 - Removing the System Board
Chapter 9 Remove/Replace Procedures 100 4. Repeat Step 3 for the three-remaining snap rivet housings and snap rivets. 5. Connect the chassis fan’s power connector. 6. If necessary, replace any accessory boards removed to allow clear access to the fan. 7. Replace the left side cover. 8. Replace the e...
Page 101 - Replacing the System Board
Chapter 9 Remove/Replace Procedures 101 Replacing the System Board 1. Remove the replacement system board and any cables from the anti-static shipping container. 2. Place the system board on an anti-static pad and set all jumper connections as recorded during the system board removal. 3. Place the s...
Page 103 - Index
103 Index accessory boards removing, 95 replacing, 96 acetone, 43 ACPI Advanced Configuration and Power Management Interface, 11 AGP video display modes, 8 ammonia, 43 anti-static wrist strap, 71 backup tape drive replacing, 83 battery problems, 52 removing, 99 replacing, 100 benzene, 43 bezel, uppe...
