HP J8763A - Manual
HP J8763A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – My ProCurve; . After registering and entering the; My Manuals; Software Updates Are; Free; Register for Automatic Notification of Updates.; Management and Configuration Guide
- Page 3 – or; reload
- Page 4 – Mini-GBIC Operation Notes; write memory; For some older network devices,; Auto; At a minimum, make sure the
1
Read Me First
f
or the ProCurve Switch vl Modules (J8763A, J8764A, J8765A,
J8766A, J8768A, J8776A, and J9033A)
Note
You can install, exchange, or remove modules after the switch has been powered on. Whenever a module is
installed during this process, it is initialized and tested for correct operation. During this process, the switch
Self Test LED is on. If you hot swap another module while the switch is initializing and testing the first module,
it is possible to cause the first module or the entire switch to be reset.
Hot Swap Precautionary Procedures.
To prevent the modules or switch from being reset when you must hot
swap multiple modules, follow these simple precautions:
■
Do not install/remove any modules from the switch while the switch Self Test LED is lit.
■
Before removing or installing any modules, make sure that all network cables are disconnected from
the module.
See the “Installing the Modules” section of the
ProCurve Switch vl Modules Installation Guide,
for more
information.
View or Download the Manual Set
The printed
Installation and Getting Started Guide
shipped with your ProCurve product describes installing,
minimally configuring, and troubleshooting. For further software feature and configuration information, please
visit the ProCurve Web site, where you can freely view or download all the latest manuals for your product. To
do so:
1.
Go to
.
2.
To display the list of downloadable manuals, click on the following links:
Technical support
Product manuals (all)
ProCurve Switch 4200vl series
.
(You may want to bookmark this Web page for easy access in the future.)
Software Requirements:
For the J8768A and the J9033A modules, software release L.10.20 or later is required on your Switch
4200vl.
For the J8766A module, software release L.11.xx or later is required on your Switch 4200vl.
All
other vl modules covered by this document or referenced above, are supported beginning with the
original software release, L.10.01. To download this version of software, go to the ProCurve Web site
at
then click on
Software updates
to go to the “ProCurve Networking software
updates” page. Under
Latest software
click on
Switches
to go to the page that has the free download
for your switch. For installation information refer to the
ProCurve Switch vl Modules Installation
Guide
, that came with your vl modules.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 You can also register on the My ProCurve portal to receive a set of ProCurve switch manuals on CD-ROM. To register and request a CD go to www.procurve.com and click on My ProCurve . After registering and entering the portal, click on My Manuals . Software Updates Are Free ! ProCurve Networking pro...
3 Saving the Configuration After Installing or Exchanging a Module The following cases automatically result in a change to the running-configuration on your switch: ■ If you replace a module with another module of a different type and then reboot the switch ■ If you install a module in a slot that h...
Mini-GBIC Operation Notes Revision “B” mini-GBICs only. This product requires ProCurve revision “B” or later mini-GBICs (product number ends with the letter “B” or “C”, for example J4858B, J4859C). These switches do not support revision “A” mini-GBICs. Use only genuine ProCurve mini-GBICs. Non-ProCu...
