HP FP9419 - Manual

User’s Guide 2–1 2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with your monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with your monitor, see “Pow...

Safety and Maintenance Guidelines 2–2 User’s Guide Maintenance Guidelines To enhance the performance and extend the life of your monitor: ■ Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating properly or has been dropped or damaged, contact ...

Safety and Maintenance Guidelines User’s Guide 2–3 ■ Keep your monitor in a well-ventilated area, away from excessive light, heat or moisture. ■ Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objects of any kind into cabinet ...

Safety and Maintenance Guidelines 2–4 User’s Guide Shipping the Monitor Keep the original packing box in a storage area. You may need it later if you move or ship your monitor. When you ship the monitor, you should remove the base from the pedestal. Removing the Monitor Base Read the following warni...

User’s Guide 3–1 3 Setting Up the Monitor Before You Begin 1. Unpack the monitor. Make sure all contents are included. Store the boxes. 2. Ensure that the power is turned off to the monitor, computer system, and other attached devices (monitor ships in off position). 3. Determine the video cable or ...

Setting Up the Monitor 3–2 User’s Guide Installing the Monitor You can install the monitor on a desktop or wall mount. Place the monitor in a convenient, well-ventilated location near your computer. If the monitor will be installed on a: ■ Desktop or table, see the “Placing the Monitor on a Desktop”...

Setting Up the Monitor 3–4 User’s Guide Mounting the Monitor Before you mount the monitor on a wall, a swing arm or other mounting fixture, you must remove the monitor pedestal and back mounting cover. You will need a Phillips head screwdriver. Read the following warning and caution statements befor...

Setting Up the Monitor User’s Guide 3–7 Connecting the Monitor To connect the monitor video input to the computer: 1. Place the monitor upright as shown in the following illustration. 2. Connect the video cable from the monitor to the video connector on the rear panel of the computer. ✎ You can conn...

Setting Up the Monitor 3–8 User’s Guide ❏ Connect one end of the DVI-D cable to the DVI input connector on the monitor. Then connect the other end to the DVI connector on the computer. Connecting the DVI-D Cable TV-OUT LCD DVI

User’s Guide 4–1 4 Operating the Monitor CD Software and Utilities The CD included with this monitor contains two files you can install on your computer: ■ An .INF (Information) file ■ An .ICM (Image Color Matching) file This CD also contains the Auto-Adjustment utility. This single pattern program ...

Operating the Monitor 4–2 User’s Guide The Image Color Matching File The .ICM files provide more accurate color representation by supplying data to graphics programs to provide consistent color matching from monitor screen to printer, or from scanner to the monitor screen. The .ICM files contain a m...

Operating the Monitor User’s Guide 4–3 Downloading from the World Wide Web To download the latest version of .INF and .ICM files from the HP Monitors Support Web site: 1. Refer to: http://www.hp.com/support Select your country/region. 2. Follow the links for your monitor to the support page and down...

Operating the Monitor User’s Guide 4–5 Front Panel Components The monitor buttons are located under the front panel. A B C D E F G

Operating the Monitor User’s Guide 4–7 Using the On-Screen Display Press the menu button under the front panel of your monitor to view the On-Screen Display (OSD) Menu. The Main Menu window displays on top of the contents of the screen. You can use the + and – keys to control the monitor’s features....

Operating the Monitor 4–8 User’s Guide 7. Select Save and Return . ❏ If you don’t want to save the setting, select Cancel from the Advanced Menu or Exit from the Main Menu. 8. Press the menu button to exit the OSD. ✎ If the buttons remain untouched for 30 seconds (factory default) while displaying a...

Operating the Monitor User’s Guide 4–9 Advanced Menu OSD To access the Advanced Menu OSD, press the menu button again (twice), or select Advanced Menu from the Main Menu. The Advanced Menu level 1 displays. ✎ After selecting the Advanced Menu from the Main Menu, the Advanced Menu remains the default...

Operating the Monitor User’s Guide 4–11 Selecting the Video Input Connectors The two input connectors are: 1. VGA connector (analog) 2. DVI-D connector (digital) The monitor will automatically determine which inputs have valid video signals and display the image. The inputs can be manually selected ...

Operating the Monitor 4–12 User’s Guide Identifying Monitor Conditions Special messages will display on the monitor screen for the following monitor conditions: ■ Input Signal Out of Range SET MONITOR TO:1280 x 1024 @ 60 Hz Moves around screen — Indicates the monitor does not support the video input...

Operating the Monitor User’s Guide 4–13 Adjusting Screen Quality The Auto-adjustment feature automatically fine-tunes the image quality for display size, position, clock, and phase each time a new video mode is displayed. For more precise adjustments, run the Auto-Adjust software on the CD. See “Usi...

Operating the Monitor 4–14 User’s Guide Entering User Modes The video controller signal may occasionally require a custom user mode if you are not using a standard graphics adapter or preset mode. In this condition, you may need to create a user mode. You can use the OSD (On-Screen Display) to: ■ Cr...

Operating the Monitor User’s Guide 4–15 Power Saver Feature When the monitor is in normal operating mode, the Power light is green and the monitor uses less than 50 watts of power.The monitor also supports a power saver mode that is controlled by the PC. When the monitor is in the reduced power stat...

User’s Guide A–1 A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power switch is turned off. ...

Troubleshooting User’s Guide A–3 Using the World Wide Web Before contacting customer service, refer to the HP Support Web site at: http://www.hp.com/support Select your country/region, and then follow the links to the support page for your monitor.

Troubleshooting A–4 User’s Guide Preparing to Call Technical Support If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical support. Have the following available when you call: ■ The monitor ■ Monitor model number (located on label in back of mon...

User’s Guide B–1 B Technical Specifications FP9419 LCD Monitor FP9419 LCD Monitor DisplayType 19.0 inchesTFT LCD Active Matrix 48.3 cm Viewable Image Size 19.0-inch diagonal 48.3 cm Tilt –5 to 30 o Face Treatment Anti-glare polarizer with hard coating Maximum Weight 15.4 lbs. (unpacked) 7 kg (unpack...

Technical Specifications User’s Guide B–3 Preset Video Modes This monitor automatically recognizes fifteen preset video input modes that will appear properly sized and centered on the screen. The following modes are assigned at the factory and are the most commonly used display resolutions. Factory ...

Technical Specifications B–4 User’s Guide LCD Monitor Quality and Pixel Policy The FP9419 LCD Monitor uses high-precision technology, manufactured according to high standards, to guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright...

Technical Specifications User’s Guide B–5 Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100–120V or 200–240V .The power cord set (flexible cord or wall plug) received with the...

User’s Guide C–1 C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte...

Agency Regulatory Notices C–2 User’s Guide Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment. Cables Connections to this device...

Agency Regulatory Notices C–4 User’s Guide Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Ca...

Agency Regulatory Notices User’s Guide C–5 Korean Notice EPA Energy Star Compliance Monitors that are marked with the Energy Star ® Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Hewlett-Packard Company has determined that this product meets the Energy Star gui...

Agency Regulatory Notices C–6 User’s Guide TCO ‘99 Requirements You have just purchased a TCO ‘99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further ...

Agency Regulatory Notices C–8 User’s Guide Environmental Requirements Flame retardants: Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay, the spread of fire. Up to 30% of the plastic in a computer casing ca...