HP EM886A8#ABA - Manual

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source andconnection appropriate for this monitor. For information on the correct power cord set to use with themonitor, refer to the Power Cord Set R...

Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only thosecontrols that are covered in the operating instructions. If the monitor is not operating properly orhas been dropped o...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. Attaching the Monitor Base 1. Set the base on a flat surface such as a table top. 2. Using both hands, position the pede...

Rear Components Figure 3-2 Rear Components Component Function 1 AC Power Connector Connects the AC power cord to the monitor. 2 VGA Connector Connects the VGA cable to the monitor. Connecting the Cables 1. Place the monitor in a convenient, well-ventilated location near the computer. NOTE: You can r...

When the monitor is powered on, a Monitor Status message is displayed for five seconds. The messageshows the current active input signal, the current preset display resolution, and the recommended presetdisplay resolution. Using the Accessory Rails The monitor features accessory rails on the rear th...

Locating the Rating Labels The rating labels on the monitor provide the spare part number, product number, and serial number.You may need these numbers when contacting HP about the monitor model. The rating labels arelocated on the rear panel of the monitor. Figure 3-8 Locating the Rating Labels Ins...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on the computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● auto-adjustment pattern utility ● additional software for the monitor model NOTE: If the monitor does...

Installing the .INF and .ICM Files After you determine that you need to update, you can install the .INF and .ICM files from the CD ordownload them. Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu is di...

Front Panel Controls Table 4-1 Monitor Front Panel Controls Control Function 1 Menu Opens, selects or exits the OSD menu. 2 – (minus)/Auto ● If the OSD menu is on, press to navigate backwardthrough the OSD menu and decrease adjustmentlevels. ● If the OSD menu is inactive, press to activate the autoa...

Adjusting the Monitor Settings The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP DisplayAssistant utility. NOTE: If there is a problem with the display settings, try resetting the settings to the factory defaults by opening the OSD and selecting Factory Reset ...

OSD Menu Selections The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions.After changing an OSD menu item, and if the menu screen has these options, you may choose to: ● Cancel —to return to the previous menu level. ● Save and Return —to save all cha...

Icon Main Menu Submenu Description DDC/CI Support Allows the computer to control some OSD menufeatures such as brightness, contrast and colortemperature. Set to: ● On ● Off The factory default is On. Bezel Power LED Turns off the power LED on the front panel of themonitor. The factory default is On....

NOTE: The Clock and Clock Phase controls are adjustable only when using an analog input. These controls are not adjustable for digital inputs. The Clock must first be set correctly since the Clock Phase settings are dependent on the main Clocksetting. Use these controls only when the auto-adjustment...

● No Source Signal —Indicates the monitor is not receiving a video signal from the PC on the monitor video input connector. Check to determine if the PC or input signal source is off or in the powersaving mode. ● Auto Adjustment in Progress —Indicates the auto-adjustment function is active. ● Monito...

3. Press the Menu button to select Management . 4. Scroll down and highlight and select Sleep Timer > Set Current Time . NOTE: You must set the current local time before you reset the time for Sleep Time or On Time . Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m...

Table 4-3 HP Display LiteSaver Configuration Options Select This Option To Do This Enable Display LiteSaver Enables the HP Display LiteSaver functions; deselect to disable the HP DisplayLiteSaver. Display Off Sets the time when the monitor automatically turns off. This does not affect screensaver op...

Installing the sRGB ICM File for Microsoft Windows 2000 and Windows XP NOTE: To complete the following procedure, you must be logged in as an administrator or a member of the administrator’s group. If the computer is connected to a network, network policy settings mayprevent you from completing this...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommendedsolutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power button on front panel ofthe monitor is t...

B Technical Specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical levelspecifications for performance and actual performance may vary either higher o...

Recognizing Preset Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults.This monitor automatically recognized these preset modes and they will appear properly sized andcentered on the screen. LE1711 and LE1911 Models Table B-3 Fact...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a resid...

Hewlett Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800-HP-INVENT (1-800 474-6836) For questions regarding this FCC declaration, contact: Hewlett Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identi...

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany German Ergonomics Notice HP products which bear the “GS” approval mark, when forming part of a system comprising HP brandcomputers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomic...

Product Environmental Notices ENERGY STAR® Qualification HP Displays marked with the ENERGY STAR® certification mark meet the requirements of the U.S.Environmental Protection Agency (EPA) ENERGY STAR program. The EPA ENERGY STAR®certification mark does not imply endorsement by the EPA. As an ENERGY ...

Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of withyour household waste. Instead, it is your responsibility to dispose of your waste equipment by handingit over to a de...

11363-2006 11363-2006 Turkey EEE Regulation In Conformity with the EEE Regulation EEE Yönetmeli ğ ine Uygundur Product Environmental Notices 35

D LCD Monitor Quality and Pixel Policy The TFT monitor uses high-precision technology, manufactured according to HP standards, toguarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections thatappear as small bright or dark spots. This is common to all LCD displays ...