HP C110 - Manual

Models C160L/C160/C180/C200/C240 Emissions Regulations v Models C160L/C160/C180/C200/C240Emissions Regulations Federal Communications Commission (FCC) This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant topart 15 of the FCC Rules and the Canadian ...

Models C160L/C160/C180/C200/C240 Emissions Regulations vi computer. Changes or modifications not expresslyapproved by Hewlett-Packard could void the user’sauthority to operate the equipment. Operation of this device is subject to the followingconditions: • This device may not cause harmful interfere...

Models C100/C110 Emissions Regulations vii Models C100/C110 EmissionsRegulations Federal Communications Commission (FCC) This equipment has been tested and found to complywith the limits for a Class A digital device, pursuant topart 15 of the FCC Rules and the Canadian Depart-ment of Communications....

Models C100/C110 Emissions Regulations viii computer. Changes or modifications not expresslyapproved by Hewlett-Packard could void the user’sauthority to operate the equipment. Operation of this device is subject to the followingconditions: • This device may not cause harmful interference. • This de...

Emissions Regulations Compliance ix Emissions Regulations Compliance Any third-party I/O device installed in HP system(s)must be in accordance with the requirements set forthin the preceding Emissions Regulations statements. Inthe event that a third-party noncompliant I/O device isinstalled, the cus...

Electrostatic Discharge (ESD) Precautions x Electrostatic Discharge (ESD)Precautions Electrostatic charges can damage the integrated cir-cuits on printed circuit boards. To prevent such dam-age from occurring, observe the following precautionsduring board unpacking and installation: • Stand on a sta...

Laser Safety Statement (U.S.A. Only) xi Laser Safety Statement (U.S.A. Only) The CD ROM mass-storage system is certified as aClass-1 laser product under the U.S. Department ofHealth and Human Services (DHHS) Radiation Per-formance Standard according to the Radiation Controlfor Health and Safety Act ...

Contents xiii 1 Product Information Product Description 3 System Unit Front Panel Controls 6 System Power Switch 6 Power LED 7 System LEDs 7 Audio Controls 8 Storage Device Controls and Features 8 CD-ROM Drive 9 DDS Tape Drive 11 Floppy Disk Drive 13 System Unit Rear Panel Connectors 14 Security Loo...

Contents xiv Operating System Overview 28 2 Environmental/Installation/PM Environmental Specifications 31 Installation 33 Preventive Maintenance 33 3 Configuration Workstation Configurations 37 FRU Configurations 38 Internal Storage Configurations 38 Allowable Memory Configurations 50 Monitor-Type S...

Contents xv Graphics Configuration Restrictions 60 4 Troubleshooting Getting Ready to Troubleshoot 63 Dealing with a Boot Failure 68 Searching for Bootable Media 70 Stable Storage 71 Boot Command Notations 71 Supported Boot Paths 72 ISL Environment 72 Selftest Failures 73 Chassis Display Codes 77 Ru...

Contents xvi Storage Devices 121 Human Interface Board 123 Main Tray Assembly 124 Removing Memory Modules 125 Installing Memory Modules 127 Removing Second Level Cache Modules (C160L) 129 Installing Cache Modules 131 Removing PCI, EISA, and GSC Option Boards 133 EGRAM (Enhanced Graphics RAM) Board 1...

Contents xvii Service Manuals 171 Reference Manuals 171 8 Service Notes 9 Boot Console Interface Model C100/110 Accessing the Boot Console Interface 179 Boot Console Menus 181 Searching for Bootable Media 184 Resetting the Workstation 186 Displaying and Setting Paths 187 Displaying and Setting the M...

Contents xviii Displaying the LAN Station Address 204 Displaying System Information 205 Displaying PIM Information 206 Configure and Display LAN Settings 207 Stable Storage 209 ISL Environment 210 Invoking ISL from the Boot Console Interface 210 ISL User Commands 211 Updating System Firmware with OD...

Contents xix Changing the Console to External Terminal 235 Displaying the Status of the System I/O 236 Setting the Auto Boot and Auto Search Flags 237 Displaying and Setting the Fastboot Mode 239 Displaying the LAN Station Address 240 Configure and Display LAN Settings 241 Displaying System Informat...

Contents xx Figures System Unit Front Panel Controls 6 CD-ROM Drive Controls and Features 9 DDS-DC Drive Controls and Indicators 11 DDS-2 Drive Controls and Indicators 11 Floppy Drive Controls and Features 13 System Unit Rear Panel Connectors 15 Disk Tray Positions 38 Hewlett-Packard 2 GB Fast, Wide...

Contents xxi Figures DDS Drive Switch Settings for Data Compression Oper-ation Mode 49 Memory Connectors (Model C100/110) 51 Memory Connectors (Model C160L) 51 Memory Connectors Model (C160/180XP/200/240) 52 Power On Troubleshooting 64 Selftests Troubleshooting 65 HP-UX Compatible Mode Troubleshooti...

Contents xxii Figures Removing a Storage Device 122 Removing the Human Interface Board 123 Removing the Main Tray Assembly 124 Memory Module Location (C100, C110) 125 Memory Module Location (C160L) 126 Memory Module Location (C160, C180XP, C200) 126 Removing a Memory Module 127 Installing Memory Mod...

Contents xxiii Figures Removing the CPU Area Fan Assembly 143 Removing the Fan 144 Removing the Rear Panel 145 Removing the I/O Board 148 Removing the I/O Extension Board 149 Removing the Battery 150 Removing the Backplane 151 Removing the Power Supply 153 Removing the Power Interconnect Board 154 P...

Contents xxiv Tables CD-ROM Drive Controls and Features 9 DDS Tape Drive Controls and Features 12 Floppy Drive Controls and Features 13 Audio Electrical Specifications 18 Serial I/O Pins 20 PS/2 Keyboard and ITF Keyboard Equivalent Keys 24 Environmental Specifications 31 Storage Configurations 39 De...

Contents xxv Tables Fan Power Pinouts 162 LED Power Pinouts 162 System Paths 187 Mnemonic Style Notation for Boot Paths 188 Graphics Configurations and Hardware Slots 191 System Paths 225 Mnemonic Style Notation 226

Product Information Product Description 3 Product Description The C Class workstations contain the following keyfeatures: • Processor Performance: 100 MHz (Model C100)120 MHz (Model C110)160 MHz (Model C160L)160 MHz (Model C160)180 MHz (Model C180XP)200 MHz (Model C200)236 MHz (Model C240) • Operati...

Product Information Product Description 4 • Memory 32 MB to 512 MB Main Memory in pairs of 16 MB,32MB, or 64 MB modules - four pairs maximum(C100/110/160L)32 MB to 768 MB Main Memory in pairs of 16 MB,32MB, or 64 MB modules - six pairs maximum(C160/180)32 MB to 1.5 GB main memory in pairs of 16 MB,3...

Product Information System Unit Front Panel Controls 6 System Unit Front Panel Controls Figure 1 shows the location of the system unit frontpanel controls. Figure 1 System Unit Front Panel Controls System Power Switch Use the Power switch to power the system unit on andoff. Storage Devices Power Swi...

Product Information System Unit Front Panel Controls 7 NOTICE: There is no need to manually shut down the HP-UX operating system on your workstation beforepowering it off. When you turn off the powerswitch, your workstation automatically shuts downthe operating system before terminating the power. P...

Product Information System Unit Front Panel Controls 8 Audio Controls Next to the system LEDs are the following audio con-trols: The volume control, headset jack, and microphonejack features of the CD-ROM are supported throughapplications only. For more information on the features and electricalspec...

Product Information System Unit Front Panel Controls 9 CD-ROM Drive Figure 2 shows the operating controls and features ofthe CD-ROM drive, and Table 1 describes them. Figure 2 CD-ROM Drive Controls and Features Table 1 CD-ROM Drive Controls and Features Control/Feature Purpose Busy Indicator Lights ...

Product Information System Unit Front Panel Controls 10 Eject Button Press to open the disc tray andinsert or remove a disc. Whenthe drive is in use, press the ejectbutton for more than one secondto open the disc tray. Emergency Eject Insert the end of a paper clip toopen the disc tray when theworks...

Product Information System Unit Front Panel Controls 11 DDS Tape Drive Your DDS tape drive is either a DDS-DC or DDS-2tape drive with a 3.5-inch form factor, data compres-sion, and a single-ended SCSI interface. Both drivesincorporate data compression capability and are high-capacity, high transfer-...

Product Information System Unit Front Panel Controls 13 Floppy Disk Drive Figure 5 shows the operating controls and features ofthe floppy drive, and Table 2 describes them. Figure 5 Floppy Drive Controls and Features Table 3 Floppy Drive Controls and Features Control Feature Purpose Eject Button Pus...

Product Information System Unit Rear Panel Connectors 14 System Unit Rear Panel Connectors This section describes the following connectors on thesystem unit’s rear panel: • Security loop • Audio connectors • Keyboard and mouse connectors • HP parallel (Centronics) I/O connector • 802.3 network conne...

Product Information System Unit Rear Panel Connectors 15 Figure 6 System Unit Rear Panel Connectors Security Loop The security loop provides a means of locking thestorage tray with a padlock or other locking device, toprevent unauthorized removal from the system. Audio Line In PS/2 Mouse PS/2 Keyboa...

Product Information System Unit Rear Panel Connectors 16 Audio Connectors The C Class workstations have audio input and outputcapability through external input and output connec-tors on the rear panel and through an internal speaker.The rear panel contains the Line IN (Stereo line-in)and Line OUT (S...

Product Information System Unit Rear Panel Connectors 17 • Audio Outputs Line-out Headset Built-in mono speaker • Audio CODEC Crystal CS4215

Product Information System Unit Rear Panel Connectors 19 Keyboard and Mouse Connectors PS/2 Keyboard and Mouse Connectors The PS/2 connectors provide an interface for the key-board, mouse, and a variety of other pointing devices,such as trackballs, to the system. Consult the docu-mentation that acco...

Product Information System Unit Rear Panel Connectors 20 Serial Input/Output Connectors There are a variety of pointing devices (mouse ortrackball) or peripheral devices that can attach to theSerial Input/Output (SIO) ports on the workstation.Peripheral devices include printers, plotters, modems,and...

Product Information System Unit Rear Panel Connectors 21 SCSI Connectors Use the SCSI connectors to connect external SCSIdevices such as DDS-format tape drives and CD-ROMdrives. Consult the documentation that accompanieseach SCSI device for specific information concerningits use. Refer to Appendix C...

Product Information Monitors 22 Monitors The Models C100/C110/C200 do not have a built-ingraphics controller. A graphics board is installed in onof the option slots. The Models C160L, C160, andC180 have a graphics controller built-in on the I/Oboard. The Model C180XP also comes with anextended graph...

Product Information Keyboards 23 Keyboards There are two types of Hewlett-Packard keyboardsavailable: • PS/2 Keyboard (PS/2 interface)(All C Class Workstations) • ITF Keyboard (HP-HIL interface)(C100/110/C160/C180 only) CAUTION: With the HIL interface, use only devices thatconform to the HP-HIL spec...

Product Information Keyboards 26 6/ (number pad) 6 (number pad) 7/Home (number pad) 7 (number pad) 8/ (number pad) 8 (number pad) 9/Pg Up (number pad) 9 (number pad) ./Del (number pad) . (number pad) Ctrl (left) Ctrl Ctrl (right) No Equivalent Table 6 PS/2 Keyboard and ITF Keyboard Equivalent Keys P...

Product Information Pointing Devices 27 Pointing Devices The PS/2 connector, the HIL port, or the Serial portssupport using an HP three-button mouse, a trackball,or other options as pointing devices. For instructionson using a particular device, see the manual that camewith that device. For general ...

Product Information Operating System Overview 28 Operating System Overview The C Class workstations use the HP-UX operatingsystem. The individual models require the followingminimum versions: Model C100/110 - HP-UX 9.05 or later Model C160L - HP-UX 10.20 or later Model C160 - HP-UX 10.20 or later Mo...

Environmental/Installation/PM Environmental Specifications 31 Environmental Specifications Table 7 lists the environmental specifications for the CClass workstations. Table 7 Environmental Specifications Type Specifications Altitude Operating 0-15,000 ft Non-operating 40,000 ft DC magnetic field Ope...

Environmental/Installation/PM Environmental Specifications 32 Vibration Operating random 0.21 G rms, 5-50 Hz Swept sine survival 0.5 G peak, 5-500 Hz Random survival 2.09 G rms, 5-500 Hz Acoustics <5 bels 5-30˚ C <6 bels 30-40˚ C Table 7 Environmental Specifications Type Specifications

Environmental/Installation/PM Installation 33 Installation Refer to Hardware Installation Card C Class (PartNumber A4200-90012) for system installation infor-mation. Preventive Maintenance The system unit requires no preventive maintenance.Some removable media storage devices require opera-tor preve...

Environmental/Installation/PM Preventive Maintenance 34

Configuration Workstation Configurations 37 Workstation Configurations Refer to the HP 9000 C Class Configuration Guide fora complete list of supported accessories, peripherals,and operating systems for your workstation.

Configuration FRU Configurations 38 FRU Configurations This section provides information for setting up orchanging the configuration of the system FieldReplaceable Units (FRUs). Internal Storage Configurations Each storage device is restricted as to where in thestorage tray it may be installed. Befo...

Configuration FRU Configurations 39 Table 9 lists the recommended SCSI IDs for internalstorage devices. Figure 8, Figure 9, and Figure 10show the FWD SCSI and UWSE SCSI ID settings forthe hard disk drives. Figure 11 and Figure 14 show theNarrow Single-Ended SCSI ID settings for the CD-ROM drive and ...

Configuration FRU Configurations 40 NOTICE: The floppy disk drive is not a SCSI device. Table 9 Default SCSI IDs Fast, Wide Differential SCSI 1st Hard Disk Drive ID 6 2nd Hard Disk Drive ID 5 3rd Hard Disk Drive ID 4 Ultra Wide Single-Ended SCSI 1st Hard Disk Drive ID 6 2nd Hard Disk Drive ID 5 3rd ...

Configuration FRU Configurations 41 Figure 8 Hewlett-Packard 2 GB Fast, Wide Differential DiskDrive Jumper Settings (1-inch Low Profile) SCSI ID 6 5 4 3 2 1 0 SCSI ID 15 14 13 12 11 10 9 8

Configuration FRU Configurations 42 Figure 9 Seagate 2 GB FWD or UWSE Disk Drive JumperSettings (1-inch Low Profile) SCSI ID Jumpers SCSI ID 6 5 4 3 2 1 0 SCSI ID 15 14 13 12 11 10 9 8

Configuration FRU Configurations 48 Figure 15 DDS-2 Tape Drive SCSI Address/Jumper Settings

Configuration FRU Configurations 50 Allowable Memory Configurations The Model C100/110/160L workstations have 8 mem-ory slots, labeled 0A, 0B through 3A, 3B. The mem-ory configuration is 32 MB to 512 MB installed inpairs of 16 MB, 32 MB, or 64 MB memory modules. The Model C160/180XP/200/240 workstat...

Configuration FRU Configurations 53 Monitor-Type Selection The built-in graphics in the C Class workstations sup-port the following two monitors: • 17-inch, 1280x1024 color monitor (A4032A) • 20-inch, 1280x1024 color monitor (A4033A) The monitor type does not have to be changed on theworkstation sin...

Configuration Graphics Configurations 54 Graphics Configurations This section describes the rules for installing and con-figuring graphics options in your C Class workstation. Special Video Configuration Statementsfor all Systems The following statements apply only to those applica-tions which inclu...

Configuration Graphics Configurations 57 Graphics Configuration Restrictions This subsection describes restrictions on the installa-tion and support of graphics adapters. Graphics Displays The system supports only four graphics displays at a time. A “display” is a video out-put port or connector. Fo...

Troubleshooting Getting Ready to Troubleshoot 63 Getting Ready to Troubleshoot To troubleshoot a C Class workstation, you must befamiliar with the HP-UX operating system and be ableto start and stop processes. You should also be familiarwith the boot ROM diagnostics, ISL diagnostics, andthe SupportW...

Troubleshooting Getting Ready to Troubleshoot 64 Figure 20 Power On Troubleshooting

Troubleshooting Getting Ready to Troubleshoot 65 Figure 21 Selftests Troubleshooting

Troubleshooting Getting Ready to Troubleshoot 66 Figure 22 HP-UX Compatible Mode Troubleshooting

Troubleshooting Dealing with a Boot Failure 68 Dealing with a Boot Failure To start the workstation from an operating systemstored on a device different from the usual bootdevice, to boot from a different disk, or to boot fromanother type of device (such as a DDS tape drive), seethe following situat...

Troubleshooting Dealing with a Boot Failure 70 Searching for Bootable Media To list all devices that may contain bootable media, goto the Main Menu of the Boot Console Interface andthen type the following at the prompt: search ipl The search may turn up more devices than there arelines on the displa...

Troubleshooting Dealing with a Boot Failure 71 Stable Storage Stable Storage is non-volatile memory associated witheach PA-RISC processor module. Stable storage isused by the processor (CPU) to store device pathinformation, the state of the boot flags, HPMC errorinformation, and operating system ini...

Troubleshooting Dealing with a Boot Failure 72 Supported Boot Paths SCSI devices are bootable when connected to the NSESCSI and FWD or UWSE SCSI ports on the Systemcard. Diskless workstations can only boot from theLAN port on the System card. ISL Environment The ISL environment provides the means to...

Troubleshooting Selftest Failures 73 Selftest Failures Chassis codes are the key to debugging selftest errors.If a failure is found during selftest, chassis codes aredisplayed in the diagnostic LEDs. Using Table 13, find the LED error code . To get additional information about failures from theboot ...

Troubleshooting Selftest Failures 74 In the following tables, shaded LEDs indicate thatthey are lit. Table 12 LED Error Codes (C100/110) LED Value RS-232 Chassis Code Range Description N/A Reserved 7500 No memory found FAULTLikely cause: SIMMs or processorboard 7501, 7502 Not enough memory found FAU...

Troubleshooting Selftest Failures 75 Any fault notin this tableincluding1000-1019 Unknown FAULT CBF0 - CBFF HPMC FAULT A000 - A0C0 No console/IPL error FAULT N/A Reserved N/A Reserved N/A Power on value (processor board faultwhen this value remains for more thanone second) Table 12 LED Error Codes (...

Troubleshooting Selftest Failures 77 Chassis Display Codes Below are definitions for all Raven-U/U+ chassis displaycodes. The codes are organized in approximate numericalorder for ease of reference. These codes are displayedon the serial console, if enabled. Below the definitions is a chronological ...

Troubleshooting Running System Verification Tests 95 Running System Verification Tests HP-UX uses an online diagnostics product called theSupport Tools Manager that allows system operationverification. Three interfaces are available with the Support ToolsManager: a command line interface (accessed t...

Troubleshooting Running System Verification Tests 96 6 To verify the system operation, type the following atthe CSTM> prompt: verify all Messages similar to the following appear: Verification has started on device (CPU).Verification has started on device (FPU). CSTM>Verification of (FPU) has c...

Troubleshooting Running ODE-Based Diagnostics 97 Running ODE-Based Diagnostics The Offline Diagnostic Environment (ODE) consistsof diagnostic modules for testing and verifying systemoperation. ODE provides all the necessary functionsfor the user to load specified tests and interact withthose tests. ...

Troubleshooting Running ODE-Based Diagnostics 98 • mapper - identifies the configuration of HPPA systems.It displays path, identification, and revision informationof I/O components, configuration of memory controllers,processors, co-processors, cache, and TLB, as well asprocessor board component rev...

Troubleshooting Troubleshooting the SCSI I/O Board 99 Troubleshooting the SCSI I/O Board The following flowcharts guide you through trouble-shooting the ultra, wide, single-ended SCSI core I/Oboard and the fast, wide, differential SCSI core I/Oboard.

Field Replaceable Units 106 This chapter lists the C Class Field Replaceable Units(FRUs) and provides procedures and illustrationsshowing their removal and replacement. Use the following tools to remove or replace FRUs: • Light-duty flat blade screwdriver with 150-mm (6-in.)blade • ESD equipment (se...

Field Replaceable Units Exchange and Nonexchange Part Numbers 107 Exchange and Nonexchange PartNumbers In this chapter we refer to exchange and nonexchangepart numbers. You must return FRUs with exchange part numbers inexchange for a replacement FRU. Do not return FRUswith nonexchange part numbers. ...

Field Replaceable Units Exchange and Nonexchange Part Numbers 108 Figure 26 shows the Main Tray FRUs for the C Classworkstations. The numbers correspond to item num-bers in Table 14 and Table 15. Figure 26 Main Tray FRUs A12 A2 A10 A4 A5 A6 A1 A8 A7 A9 A3 A11 A1

Field Replaceable Units Exchange and Nonexchange Part Numbers 109 Figure 27 shows the Storage Tray FRUs for the CClass workstations. The numbers correspond to itemnumbers in Table 14 and Table 15. Figure 27 Storage Tray FRUs B1 B2 B3 B4 B5 B6 B7 B8 B9

Field Replaceable Units Exchange and Nonexchange Part Numbers 110 Figure 28 shows the Power Supply FRUs for the CClass workstations. The numbers correspond to itemnumbers in Table 14 and Table 15. Figure 28 Power Supply FRUs Table 14 lists the exchange parts, and Table 15 lists thenonexchange parts ...

Field Replaceable Units Exchange and Nonexchange Part Numbers 111 Table 14 Exchange Parts FRU List Figure Number Part Number Description A6 A4200-66521A4200-69022A4125-69021 I/O Board (C100, C110)I/O Board (C160L, C160, C180)I/O Board (C200, C240) A7 A4200-66510A4200-66512A4200-69014A4200-69017A4200...

Field Replaceable Units FRU Removal and Replacement 115 FRU Removal and Replacement The procedures in this section describe how to removesystem unit FRUs. Observe any notices and prerequi-sites for removing a FRU. Replacement is the reverseof removal, unless noted. 1 Power off the system, the monito...

Field Replaceable Units FRU Removal and Replacement 116 Figure 29 Removing the Floor Stand 6 Lay the workstation on a flat stable surface, such as atable top or floor. CAUTION: Follow normal ESD, anti-static precautions whenhandling the workstation or any of its components.Failure to do so can cause...

Field Replaceable Units FRU Removal and Replacement 117 Storage Tray Assembly Perform the following steps to remove the storage trayassembly from the system unit: 1 Remove the storage tray retaining screw, as shown inFigure 30. Figure 30 Removing the Storage Tray Assembly 2 If installed, remove any ...

Field Replaceable Units FRU Removal and Replacement 118 Disk Interconnect Board Before removing the disk interconnect board, removethe Storage Tray Assembly from the system unit. Perform the following steps to remove the disk inter-connect board from the system unit: 1 Remove the two retaining screw...

Field Replaceable Units FRU Removal and Replacement 119 Storage Tray Bezel Before removing the storage tray bezel, remove theStorage Tray Assembly. 1 To remove the storage tray bezel, lift up on the toprear edge of the bezel and slide it out from the stor-age tray approximately 1/2-inch, as shown in...

Field Replaceable Units FRU Removal and Replacement 120 Disk Filler Panel NOTICE: If you remove a disk filler panel, you must replaceit or install a removable media storage device in itsplace. Before removing a disk filler panel, remove the Stor-age Tray Assembly. To remove a disk filler panel, inse...

Field Replaceable Units FRU Removal and Replacement 121 Storage Devices Before removing storage devices, remove the StorageTray Assembly from the system unit. Before removing a hard drive in either of the storagetray’s rear positions, remove the Disk Interconnectboard. NOTICE: Refer to chapter 3 for...

Field Replaceable Units FRU Removal and Replacement 122 Figure 34 Removing a Storage Device 3 Slide the device completely out of the storage tray andplace it on a static-free surface. When replacing storage devices, refer to the cablerouting label on the top of the storage tray. Locking Tab Floppyor...

Field Replaceable Units FRU Removal and Replacement 123 Human Interface Board Before removing the human interface board, performthe following procedures: • Remove the Storage Tray Assembly from the systemunit. • Remove the Storage Tray Bezel Perform the following steps to remove the humaninterface b...

Field Replaceable Units FRU Removal and Replacement 124 Main Tray Assembly Perform the following steps to remove the main trayassembly from the system unit: 1 If installed, remove any locking device from the securityloop on the rear of the system unit. 2 Completely loosen the four thumb screws on th...

Field Replaceable Units FRU Removal and Replacement 125 Removing Memory Modules Before removing memory modules, remove the MainTray Assembly from the system unit. Refer to Chapter 3 for information about memory con-figurations. Perform the following steps to remove memory mod-ules: 1 Locate the memo...

Field Replaceable Units FRU Removal and Replacement 127 2 To remove a memory module, push the ejector tabs oneach side of the module. Lift the memory module up andout of the connector and place it on a static-free surface.Figure 40 shows how to remove a memory module. Figure 40 Removing a Memory Mod...

Field Replaceable Units FRU Removal and Replacement 128 2 To install a memory module, close the ejector tabs oneach side of the memory connector. This lowers the forceneeded to seat the memory board. Line the memory module up with the guides, as shownin Figure 41. Make sure that the notched end of t...

Field Replaceable Units FRU Removal and Replacement 129 If only a faulty memory module is replaced, use the pdtclear command in the service menu of the Boot ConsoleInterface. Answer y to the prompt Continue? (Y/N) . Removing Second Level Cache Modules (C160L) Before removing second level cache modul...

Field Replaceable Units FRU Removal and Replacement 130 2 To remove a cache module, push the ejector tabs on eachside of the module. Lift the cache module up and out ofthe connector and place it on a static-free surface. Figure43 shows how to remove a cache module. Figure 43 Removing a Cache Module

Field Replaceable Units FRU Removal and Replacement 131 Installing Cache Modules Before installing cache modules, remove the MainTray Assembly from the system unit. You must install two cache modules. Perform the following steps to install cachemodules: 1 Locate the cache connectors on the CPU board...

Field Replaceable Units FRU Removal and Replacement 133 Removing PCI, EISA, and GSC Option Boards Before removing PCI, EISA, or GSC option boardsfrom the system unit, remove the Main Tray Assemblyfrom the system unit. Perform the following steps to remove a PCI, EISA, orGSC option board: 1 Press the...

Field Replaceable Units FRU Removal and Replacement 134 Figure 46 Removing the EISA Slider and Retainer 3 Remove the screw from the EISA retainer and remove it,as shown in Figure 46. 4 If you are removing a PCI, EISA, or GSC board grasp itby the edge with both hands and pull it straight out. Perform...

Field Replaceable Units FRU Removal and Replacement 135 NOTICE: If you are not replacing the board, perform thefollowing procedure: 1 Install a blank plate in the rear panel, as shown in Figure 47 2 Install the EISA retainer, as shown in Figure 47.3 On the blank plate, turn the locking knob clockwis...

Field Replaceable Units FRU Removal and Replacement 136 EGRAM (Enhanced Graphics RAM) Board Before removing the EGRAM board from the systemunit, perform the following procedures: • Remove the Main Tray Assembly from the system unit. • Remove any option boards. Perform the following steps to remove t...

Field Replaceable Units FRU Removal and Replacement 138 CPU Board Before removing the CPU board, remove the MainTray Assembly from the system unit. Perform the following steps to remove the CPU boardfrom the system unit: 1 Remove the Main Tray Assembly. 2 Remove the CPU board retaining screw, as sho...

Field Replaceable Units FRU Removal and Replacement 141 4 Slide the CPU board out approximately one inch, thenlift it straight up to remove it. If you are reinstalling the same CPU board in the sys-tem, repeat Steps 4 through 1 in reverse order. If you are replacing the existing CPU board with a new...

Field Replaceable Units FRU Removal and Replacement 142 System Fans Before removing the fans, remove the Main TrayAssembly from the system unit. Perform the following steps to remove the systemfans. 1 Disconnect the fan connector. 2 Press the retaining clip and swing the fan assembly outfrom the bac...

Field Replaceable Units FRU Removal and Replacement 143 Figure 53 Removing the CPU Area Fan Assembly 3 Lift the fan assembly up off of the pins.

Field Replaceable Units FRU Removal and Replacement 144 4 Pull the fan retaining clips away from the fan and removethe fan from the fan housing, as shown in Figure 54. Figure 54 Removing the Fan

Field Replaceable Units FRU Removal and Replacement 145 Rear Panel Before removing the Rear Panel, perform the follow-ing procedures: • Remove the Main Tray Assembly from the system unit. • Remove the System Fans • Remove any option boards See the section on Removing PCI, EISA, and GSCOption Boards,...

Field Replaceable Units FRU Removal and Replacement 146 I/O Board Before removing the I/O board, perform the followingprocedures: • If you are replacing the original I/O board with a newone, refer to the section, “Determining LAN ID andFDDI ID” below before removing the board. • Remove the Main Tray...

Field Replaceable Units FRU Removal and Replacement 147 Determining LAN ID and FDDI ID 1 If you are using HP-UX 9.0x, enter the following at theprompt: /etc/lanscan If you are using HP-UX 10.x, enter the following at theprompt: /usr/sbin/lanscan The output is similar to the following: Hardware Stati...

Field Replaceable Units FRU Removal and Replacement 148 Removing the I/O Board Perform the following steps to remove the I/O board: 1 Pull the ejector handles, as shown in Figure 56. Figure 56 Removing the I/O Board 2 Slide the board out slowly until it stops, then lift itstraight up. When replacing...

Field Replaceable Units FRU Removal and Replacement 149 I/O Extension Board Before removing the I/O extension board, remove theRear Panel. Perform the following steps to remove the I/O exten-sion board: 1 Remove one screw holding the I/O extension board tothe main tray, as shown in Figure 57. 2 Slid...

Field Replaceable Units FRU Removal and Replacement 150 Battery Before removing the battery, perform the followingprocedures: • Remove the Main Tray Assembly • Remove all of the PCI, EISA, and GSC option boards Lift the clip and slip the battery out of its holder, asshown in Figure 58. Figure 58 Rem...

Field Replaceable Units FRU Removal and Replacement 151 Backplane Before removing the backplane, perform the followingprocedures: • Remove the Main Tray Assembly • Remove the CPU Board • Remove the Rear Panel • Remove the I/O Board • Remove the I/O Extension Board Perform the following steps to remo...

Field Replaceable Units FRU Removal and Replacement 152 3 Remove the retaining screw from the backplane, asshown in Figure 59. 4 Lift the Backplane up and out, as indicated in Figure 59.

Field Replaceable Units FRU Removal and Replacement 153 Power Supply Before removing the power supply, remove the MainTray Assembly. To remove the power supply, loosen the captive screwand slide the power supply out of the chassis, asshown in Figure 60. Figure 60 Removing the Power Supply CAUTION: T...

Field Replaceable Units FRU Removal and Replacement 154 Power Interconnect Board Before removing the power interconnect board, per-form the following procedures: • Remove the Main Tray Assembly • Remove the Power Supply Perform the following steps to remove the powerinterconnect board: 1 Remove the ...

Diagrams System Power 157 System Power Figure 62 shows the power distribution and connec-tions for the C Class power distribution boards. Figure 62 Power Distribution Board The power supply distributes power through thefollowing connectors: CPU Board Connector (11-pin) Floppy Drive Connector (2-pin)...

Diagrams System Power 161 Table 18 lists the pinouts for floppy drive power: Table 19 lists the pinouts for hard disk drive power: 29 VDL GSC1_LS_L GND GSC1_SYNC_L 30 VDL GSC1_INTERRUPT_L GND GSC1_SYNC_H 31 VDL VDL GND GND 32 VDL VDL GND GND 33 VDL VDL GND GND 34 VDL VDL GND GND 35 VDL VDL GND GND 3...

Diagrams System Power 162 Table 20 lists the pinouts for fan power: Table 21 lists the pinouts for the LED connector: 3 GROUND black 4 +5V orange Table 20 Fan Power Pinouts Pin Number Description Wire Color 1 +12V N/A 2 GROUND N/A Table 21 LED Power Pinouts Pin Number Description Wire Color 1 Cathod...

Diagrams System Block Diagram 163 System Block Diagram The figures in this section show the system unit blockdiagrams for the C100/110, C160L, and the C160/180workstations.

Diagrams System Block Diagram 164 Figure 63 C100/110 System Unit Functional Block Diagram

Diagrams System Block Diagram 165 Figure 64 C160L System Unit Functional Block Diagram

Diagrams System Block Diagram 166 Figure 65 C160/180 System Unit Functional Block Diagram

Diagrams System Block Diagram 167 Figure 66 C200/240 System Unit Functional Block Diagram

Reference Installation Manual 171 Installation Manual Hardware Installation Card C Class A4200-90012 Service Manuals Service Handbook C100/C110, C160L, and C160/180Workstations (this handbook) A4200-90040 Precision Architecture RISC: HP Apollo 9000 Series700 Diagnostic Manual 09740-90041 System Admi...

Service Notes 174 Place service notes here. __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ _________________________________________...

Boot Console Interface Model C100/110 Accessing the Boot Console Interface 179 Accessing the Boot Console Interface To access the boot console interface, follow thesesteps: NOTICE: This procedure should be done by a systemadministrator. 1 Close any files and applications on your workstation. 2 Press...

Boot Console Interface Model C100/110 Accessing the Boot Console Interface 180 4 Press a key. You will then see the message: Boot terminated The Main Menu of the boot console appears.

Boot Console Interface Model C100/110 Boot Console Menus 181 Boot Console Menus The boot console menus follow, showing the varioustasks you can perform and the information available. The shortened version of all commands is indicated bythe uppercase letters. Help is available for all the menus and c...

Boot Console Interface Model C100/110 Searching for Bootable Media 184 Searching for Bootable Media To list all devices that may contain bootable media,follow the directions in “Accessing the Boot ConsoleInterface” earlier in this chapter, and then type the fol-lowing at the prompt: search ipl The s...

Boot Console Interface Model C100/110 Searching for Bootable Media 185 Where device_type is one of the following: fwscsi is the built-in fast, wide SCSI bus slotn.fwscsi is an optional fast, wide SCSI bus scsi is the built-in single-ended SCSI bus lan is all connections to the built-in LAN

Boot Console Interface Model C100/110 Resetting the Workstation 186 Resetting the Workstation To reset your workstation, press the power switch andlet the system perform a soft shutdown.

Boot Console Interface Model C100/110 Displaying and Setting Paths 187 Displaying and Setting Paths A path is the hardware address of a device that isattached to the I/O system of your workstation. Thepath command sets the system paths shown in Table22. To display the current settings for the system...

Boot Console Interface Model C100/110 Displaying and Setting Paths 188 The boot paths are displayed in Mnemonic StyleNotation, as shown in Table 23. To display the current setting for a particular systempath, follow the directions in “Accessing the BootConsole Interface” earlier in this chapter, and...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 190 Displaying and Setting the MonitorType Your system ships from the factory preset to use amonitor with a specific resolution and frequency. Ifyou replace your workstation’s monitor with a differ-ent type of monitor, you...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 191 Table 24 shows the possible combinations of graphicscards and slots. Graphics 3, and Graphics 4 refer to theconsole paths, GRAPHICS3, and GRAPHICS4,respectively. There is no GRAPHICS 1 or GRAPHICS2 path. Configurations...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 192 Figure 67 shows the physical layout of the EISA/GSCslots from outside the system unit. Figure 67 EISA/GSC Slots from Outside the System Unit Physical slot2 is always reserved for non-graphicscards only. The monitor com...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 193 Displaying the Current Monitor Configuration To display the current monitor configuration for yoursystem from the Configuration Menu of the boot con-sole interface, follow the directions in “Accessing theBoot Console I...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 194 Setting the Monitor Type Using the list in the example above, you can set themonitor type for graphics slot3 by typing the follow-ing: monitor graphics3 NOTICE: You can exit at this point by entering x, andthe monitor ...

Boot Console Interface Model C100/110 Displaying and Setting the Monitor Type 197 Setting the Monitor Type at Power On If you replace your workstation’s monitor with a dif-ferent monitor type, and do not set the workstation’sgraphics parameters by using the monitor commandbefore doing so, you need t...

Boot Console Interface Model C100/110 Displaying the Status of the System I/O 199 Displaying the Status of the System I/O The IO command lets you identify all built-in I/Odevices and optional I/O devices installed in the optionslots. It is available in the Information Menu. To use the IO command fro...

Boot Console Interface Model C100/110 Setting the Auto Boot and Auto Search Flags 201 To change the state of the auto boot or auto searchflags, type the following at the prompt: auto boot state or auto search state where state is on or off.

Boot Console Interface Model C100/110 Displaying and Setting Secure Mode 202 Displaying and Setting Secure Mode The SECure flag is a variable stored in non-volatilememory. (Non-volatile memory retains its contentseven after power is turned off.) If you reset this flag toa new value, the change takes...

Boot Console Interface Model C100/110 Displaying and Setting Fastboot Mode 203 Displaying and Setting Fastboot Mode When fastboot is enabled (set to on), your worksta-tion does a quick check of the memory and skips I/Ointerface testing during its power-on self tests. Thisenables your workstation to ...

Boot Console Interface Model C100/110 Displaying the LAN Station Address 204 Displaying the LAN Station Address It is sometimes necessary to supply a LAN stationaddress of your workstation to other users. Forexample, if your workstation is to become a memberof a cluster, the cluster administrator ne...

Boot Console Interface Model C100/110 Displaying System Information 205 Displaying System Information The all command allows you to display all the infor-mation shown by the individual Information Menucommands, such as the system’s processor revisionand speed, cache size, memory size, flag settings,...

Boot Console Interface Model C100/110 Displaying PIM Information 206 Displaying PIM Information The pim command allows you to display the mostrecent PIM information for the specified fault type. Todisplay PIM information or a specific fault from theService Menu, type the following at the prompt: pim...

Boot Console Interface Model C100/110 Configure and Display LAN Settings 207 Configure and Display LAN Settings The LanConfig command configures and displays thecurrent LAN settings. The C180, C200 and C240 sys-tems support 10Base-T, 100Base-T and AUI stan-dards. To automatically select the network ...

Boot Console Interface Model C100/110 Configure and Display LAN Settings 208 Configuration Menu: Enter command > LanConfig 100/Full_dx To select the AUI port (10 Mbits/sec, half duplex only),type the following at the prompt: Configuration Menu: Enter command > LanConfig AUI NOTE: The LAN setti...

Boot Console Interface Model C100/110 Stable Storage 209 Stable Storage Stable storage is nonvolatile memory associated witheach PA-RISC processor module. Stable storage isused by the processor (CPU) to store • Device path information • The state of the boot flags • HPMC error information • Operatin...

Boot Console Interface Model C100/110 ISL Environment 210 ISL Environment The ISL environment provides the means to load theoperating system (HP-UX) environment. The ISLenvironment also provides an offline platform to exe-cute diagnostic and utility programs from a bootdevice when HP-UX does not loa...

Boot Console Interface Model C100/110 ISL Environment 211 2 Answering yes (y) causes the ISL to be loaded from thespecified device. After a short time, the followingprompt appears on your screen: ISL> ISL is the program that actually controls the loading ofthe operating system. By interacting wit...

Boot Console Interface Model C100/110 Updating System Firmware with ODE 213 Updating System Firmware with ODE The Offline Diagnostic Environment (ODE) consistsof diagnostic modules for testing and verifying systemoperation. The update utility of ODE provides thecapability of updating the PDC/IODC fi...

Boot Console Interface Model C160L/160/180/200/240 Searching for Bootable Media 223 Searching for Bootable Media To list devices that contain bootable media, follow thedirections in “Accessing the Boot Console Interface”earlier in this appendix, and then type the following atthe prompt: Main Menu:En...

Boot Console Interface Model C160L/160/180/200/240 Resetting Your Workstation 224 Resetting Your Workstation To reset your workstation, follow the directions in“Accessing the Boot Console Interface” earlier in thisappendix, and then type the following at the prompt: Main Menu: Enter command > res...

Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting Paths 225 Displaying and Setting Paths A path is the hardware address of a device that isattached to the I/O system of your workstation. Thepath command sets the system paths shown inTable 25. The path command sets and display...

Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor Type 229 To display the current graphics and console informa-tion, enter the following command; monitor The correct usage for setting the graphics configura-tion is: monitor graphics_path type where valid graphics_...

Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor Type 231 Setting the Monitor Type You can set the monitor type for a graphics adapter bytyping the following: Configuration Menu: Enter command> monitor graphics(n) tt Where n is the number of the graphics adapt...

Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor Type 234 At this point, the new monitor type is active, but notsaved. Because you didn’t save the monitor type, thenext time you reboot the system the original monitortype will be used. Next, the following message ...

Boot Console Interface Model C160L/160/180/200/240 Setting the Auto Boot and Auto Search Flags 238 To change the state of the auto boot or auto searchflags, type the following at the prompt: auto boot state or auto search state where state is on or off. Autosearch searches for devices in the followi...

Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Fastboot Mode 239 Displaying and Setting the FastbootMode Access fastboot from the configuration menu. When fastboot is enabled (set to on), your worksta-tion does a quick check of the memory and skips I/Ointerface testing...

Boot Console Interface Model C160L/160/180/200/240 Displaying the LAN Station Address 240 Displaying the LAN Station Address It is sometimes necessary to supply a LAN stationaddress of your workstation to other users. For exam-ple, if your workstation is to become a member of acluster, the cluster a...

Boot Console Interface Model C160L/160/180/200/240 Updating System Firmware with ODE 250 The following commands may be entered at the UPDATE> prompt: • help - prints a one line description of each of theavailable commands in the update utility. • info - prints information on how to use the update...

Index 251 Aaudio CODEC, 17features, 16headphone jack, 8IN,, 15input, 16microphone jack, 8mute button, 8OUT,, 15outpu, 17volume control, 8 auto boot flag, changing state of, 201 auto boot,, 237auto boot, changing state,, 238auto search flag, changing state of, 201 auto search,, 237auto search, changi...