HP Broadband Service Analyzer - Manual

1 About the 25.6 Mb/s Interface Pod About the 25.6 Mb/s Interface Pod Overview The HP E5129A 25.6 Mb/s Interface Pod is a self-contained, plug-inmodule. You use it in conjunction with the HP E5200A Broadband ServiceAnalyzer to test and analyze a system under test (SUT). The interface pod generates a...

Online Help 2 Online Help The Online Help provides all the information you need to use the analyzer.Refer to the HP Broadband Service Analyzer User’s Guide for information on the Monitor/Simulate help. Refer to the Application Guide for the B-ISDN UNI Signaling Tests for information on the B-ISDN UN...

3 Front Panel at a Glance Front Panel at a Glance Access (green LED) Lights each time the interface pod is accessed by thenetwork. Signal (yellow LED) Lights when a valid signal is present at the input connector. I/O Concentrator (UTP) Accepts an electrical signal from and provides a signal to the S...

Cable and Line Connector Details 4 Cable and Line Connector Details The HP E5129A 25.6 Mb/s Interface Pod’s connector pin configurationadheres to the specification defined in the IBM Corporation’s ATM 25.6Mb/s PHY Compatibility Specification, Version 2.0, 15 October, 1993. Note In order to comply wi...

5 Cable and Line Connector Details Connector Cable Configurations The interface pod comes with three cables: • part number E1619-64300 connects a user device to the network (2 to3 in the table below) • part number E1619-64301 connects the interface pod to a user device(1 to 2 in the table below) • p...

To Set Up the Interface Pod 6 To Set Up the Interface Pod Caution Handle the interface pod with care to avoid electrostatic discharge (ESD)damage during unpacking, installation, and operation. The connectors onthe front and rear of the interface pod are susceptible to ESD. 1 Insert the interface pod...

7 To Set Up the Interface Pod To Insert the Interface Pod You can insert and remove interface pods at any time, even when theanalyzer is powered on. Initially, you insert an interface pod when you setup the analyzer. Subsequently, you insert an interface pod when youchange the physical layer interfa...

To Set Up the Interface Pod 8 To Remove the Interface Pod When you remove the interface pod, make sure you store it in a dust freelocation that meets the environmental requirements listed in“Environmental Specifications” on page 14. An electrostatic-safe bag hasbeen supplied for the storage of each ...

9 To Set Up the Interface Pod Some common system and test connections are • an intrusive system connection—network element • remote loopback • in-line test connections See the HP E5200A Broadband Service Analyzer User’s Guide or the Online Help for details about these system connections. The analyze...

To Set Up the Interface Pod 10 Automatic Configuration Parameters After you insert the interface pod and connect it to the SUT, the analyzerautomatically configures to the 25.6 Mb/s electrical signal. The analyzer sets the remaining physical layer receive and transmitparameters to the following defa...

11 To Set Up the Interface Pod To Manually Configure the Interface Pod • Note See the UNI Signaling Test Application’s Help for information on configuring the 25.6 Mb/s interface pod from the B-ISDN UNISignaling Test Application. When the configuration is complete, the analyzer updates all relevants...

What to Do Next 12 X8 Timing Marker Source Setting When you change the X8 timing marker source setting, the trafficgenerator settings are cleared. The analyzer does this because it has to re-calculate and re-adjust the total allowable transmit bandwidth to • allow for the X8 marker when you enable X...

13 Standards and Specifications Standards and Specifications Communications Standards Physical Specifications af-phy-004.400 ATM 25.6 Mb/s over Twisted Pair Cable, ATM Forum ITU-T I.432.5 B-ISDN User Interface for Physical Layer ATM 25.6 PHY compatibilityspecification IBM Corporation Weight 1.0 kg (...

Standards and Specifications 14 Environmental Specifications Parameter Nominal Min. Max. Notes Operating Temperature 5 o C (41 o F) 45 o C (113 o F) with two interface pods installed Storage Temperature –40 o C (–40 o F) 70 o C (158 o F) Humidity 15% 90% at 40 o C (104 o F) Altitude 4.6 km(2.86 mile...

page inner margin hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line outer margin for text and artwork Right body text drop top margin for modules DECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and EN 45014 Manufacturer’s Name...