HP A7540-96010 - Manual

HP A7540-96010

HP A7540-96010 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
Page: / 70

Table of Contents:

  • Page 2 – HP StorageWorks 2/8q Fibre Channel Switch Installation Guide
  • Page 3 – Contents
  • Page 4 – Maintenance menu –
  • Page 6 – Figures
  • Page 7 – About This Guide; About this Guide topics include:; Intended audience; HP StorageWorks 2/8q Fibre Channel Switch Management User Guide
  • Page 8 – Document conventions; This document follows the conventions in; Text symbols; Italics
  • Page 9 – Equipment symbols
  • Page 10 – Rack stability; Getting help; HP installation and configuration assistance
  • Page 11 – HP technical support
  • Page 13 – Introduction; Switch chassis features
  • Page 14 – Power supply; Serial port; “Cable pin configurations” on; Chassis LEDs; Figure 2
  • Page 15 – ” on page 42 for more information.; ) is an RJ-45 connector that provides a connection to a; Ethernet port
  • Page 16 – Maintenance button; “Maintenance; Resetting the switch; The switch responds as follows:; Placing the switch in maintenance mode
  • Page 17 – Fibre Channel ports and LEDs; Figure 4; Logged-In LED indications
  • Page 18 – SFP transceivers; Install SFP transceivers; Port types; Ports function as follows:
  • Page 19 – Switch management; Fabrics are managed with following tools:; Switch Manager user interface; for connection information and to the HP; Command Line Interface; for connection information; File Transfer Protocol
  • Page 21 – Planning; Consider the following when planning a fabric:
  • Page 22 – Devices; Some zoning strategies include:
  • Page 23 – The ACL zone boundary is secure against inbound traffic.; Soft zones; Soft zone boundaries yield to ACL zone boundaries.
  • Page 24 – Performance; Related performance characteristics include:; Distance; Specifications; Bandwidth
  • Page 25 – Fabric security; Fabric security consists of the following:; User account security; Admin; Simple Network Management Protocol security; Fabric management; high priority Telnet sessions
  • Page 27 – Installing; Site requirements; ” on
  • Page 28 – Installing and initially configuring the switch; Unpack the switch and verify carton contents; The 2/8q FC Switch is shipped with the components shown in; /8q FC Switch Quick Start Installation Instructions (printed)
  • Page 29 – Mount the switch; When mounting the switch in a rack, do the following:; Figure 6
  • Page 30 – and the scissor-type locking latch
  • Page 31 – Figure 8
  • Page 32 – provided screws through the bracket flanges. (
  • Page 35 – Connect the cables; Connect Fibre Channel devices to the switch; outlet or uninterruptible power supply.
  • Page 36 – Configure the switch; If Switch Manager is not installed on your system, do the following:; Installing Switch Manager on Windows; Installing Switch Manager on Linux; CD into the server or management workstation CD-ROM drive.
  • Page 37 – Backing up the switch configuration; configdata; Powering down the switch; “Management System Requirements” on page 63
  • Page 38 – Updating switch firmware; Using Switch Manager to install firmware; Open the Switch menu and select Load Firmware.; Using the CLI to install firmware
  • Page 39 – Yes
  • Page 41 – Troubleshooting; This section describes the following diagnostics and tasks:
  • Page 42 – POST diagnostics; Heartbeat LED blink patterns; “Maintenance mode
  • Page 43 – Internal firmware failure blink pattern; “Maintenance mode options” on page 47
  • Page 44 – Over temperature blink pattern; If the Heartbeat LED shows the over temperature blink pattern:
  • Page 45 – Port Error blinking pattern
  • Page 46 – Chassis diagnostics; Chassis diagnostics are indicated by the chassis LEDs, as shown in; Input Power LED is extinguished; Maintenance Provider.; System Fault LED is illuminated
  • Page 47 – Maintenance mode options
  • Page 48 – Select option 7 to reset the switch and exit maintenance mode.
  • Page 51 – Regulatory Compliance Notices; Federal Communications Commission Notice; Class A equipment
  • Page 52 – Modifications
  • Page 53 – European Union Notice
  • Page 54 – Japanese Notice; Japanese Power Cord Notice; Korean notices
  • Page 55 – Laser compliance
  • Page 56 – Battery replacement notice
  • Page 57 – Electrostatic Discharge; Prevention methods; Use conductive field service tools.
  • Page 59 – Fabric specifications
  • Page 60 – Maintainability
  • Page 61 – Dimensions
  • Page 62 – Regulatory certifications
  • Page 63 – Management System; Management system requirements
  • Page 64 – Cable pin configurations; Use one of the following connection methods.; Indirect Ethernet cable; This connection method requires a null modem F/F DB9 cable.
  • Page 65 – Establishing an Ethernet or serial connection; “Cable pin configurations” on page 64; Ethernet connection information; To establish an Ethernet connection:
  • Page 66 – Serial connection information; For Windows environments:
Loading the manual

Installation Guide

HP

StorageWorks

2/8q Fibre Channel Switch

First Edition (November 2004)

Part Number:

A7540-96010

This manual describes the features of, and installation procedures for, the HP StorageWorks 2/8q Fibre

Channel Switch.

Sections include:

■

Introduction

—provides an overview of LEDs, connections, and user controls.

■

Planning

—describes the factors to consider when planning a fabric.

■

Installing

—explains how to install and configure the switch.

■

Troubleshooting

—describes the diagnostic methods and troubleshooting procedures.

■

Regulatory Compliance Notices

—includes notices about the switch.

■

Electrostatic Discharge

—discusses static electricity concerns.

■

Specifications

—ists the switch specifications.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - HP StorageWorks 2/8q Fibre Channel Switch Installation Guide

© Copyright 2004 Hewlett-Packard Development Company, L.P.Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors ...

Page 3 - Contents

3 HP StorageWorks 2/8q Fibre Channel Switch Installation Guide Contents Contents About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4 - Maintenance menu –

Contents 4 HP StorageWorks 2/8q Fibre Channel Switch Installation Guide 2 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Other HP Models

All HP Other