HP 8100FL - Manual

HP 8100FL – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

Page: / 4 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – About Your ProCurve Series 8100fl Switches Manual Set; View or Download the Software Manual Set; Installation and Getting Started Guide; Your Free Introduction to Proactive Networking!; Free; Switches; Read Me First
• Page 3 – Mini-GBIC Operation Notes; This product requires ProCurve revision “B” mini-; Connecting the mini-GBICs to Devices with Fixed Configurations.; For some older network; Auto; At a minimum, make sure
• Page 4 – Open Source Software Acknowledgement; GNU GPL Source Code

Loading the manual

Read Me First

for the ProCurve Series 8100fl Switches – Software

Version CY.02.05.xxxx or greater

Contents

ProCurve Series 8100fl Operation and Installation Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1

Setting the System Clock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1

About Your ProCurve Series 8100fl Switches Manual Set

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2

View or Download the Software Manual Set

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2

Your Free Introduction to Proactive Networking!

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2

Software Updates Are Free!

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2

Mini-GBIC Operation Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 3

Open Source Software Acknowledgement

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4

ProCurve Series 8100fl Operation and Installation Notes

■

System Clock.

To ensure correct operation of your switch, you must update the system clock and

reload prior to configuration. This is required only for the initial installation and configuration of your
system. See

“Setting the System Clock” on page 1

for details.

■

Version B or later mini-GBICs only.

The Series 8100fl Switches do not support “A” version ProCurve

mini-GBICs. Use only ProCurve JxxxxB version mini-GBICs or later with your switch. See

“Mini-GBIC

Operation Notes” on page 3

for details.

■

Console Serial Port is only 9600 baud.

There is no auto-baud detect on the switch. To connect a

console to the switch, configure your VT-100 terminal to operate with the following settings:

9600 baud rate/8 data bits/1 stop bit/no parity/no flow control.

■

Out of band Management Port.

The 10/100Base-T Ethernet port on the management module is for

management only. It cannot be used for switching network traffic. The port is not auto-MDIX.

Setting the System Clock

To set the system date and time, use the

clock set

command from the command line interface (CLI). For more

information, refer to “Getting Started with Switch Configuration” in the

Installation and Getting Started Guide

.

You can verify the clock settings using the

show clock

command.

For example:

Switch 8100fl#clock set 18:45:29 30 September 2005

Switch 8100fl#show clock

*18:45:29 UTC Fri September 30 2005

Other HP Models

• HP CM1312 MFP
  • Manual
• HP DV2700
  • Manual
• HP 203A
  • Manual
• HP 13-2000
  • Manual
• HP 1320NW
  • Manual
• HP D4360
  • Manual
• HP W19Q
  • Manual
• HP FC2143
  • Manual
• HP ZV6000
  • Manual
• HP 7500
  • Manual