HP 643064-001 - Manual

Customer self repair 7 In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un supplemento di costo solo in alcune zone. In caso di necessità si può richie...

Customer self repair 8 defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier-/Frachtdienst. Weitere Informationen über das HP Customer Self Repair P...

Customer self repair 10 Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma van HP. Informatie over Service Partners vindt u op de HP website

Illustrated parts catalog 16 Illustrated parts catalog Mechanical components Item Description Spare part number Customer self repair (on page 5 ) 1 Plastics kit 591209-001 — a) Bezel — Mandatory 1 b) PCI card retainer* — Mandatory 1 c) Bezel assembly, power and Systems Insight Display — Mandatory 1 ...

Illustrated parts catalog 19 System components Item Description Spare part number Customer self repair (on page 5 ) 6 Power supplies — — a) 1200 W, 90% 498152-001 Mandatory 1 b) 1200 W, 94%* 579229-001 Mandatory 1 7 Fan, 92-mm, hot-plug 591208-001 Mandatory 1 8 Processor — — a) Intel Xeon X7560 proc...

Removal and replacement procedures 25 Removal and replacement procedures Required tools You need the following items for some procedures: • Torx T-15 screwdriver (provided with the server) • Phillips screwdriver • Flathead screwdriver • Diagnostics Utility Safety considerations Before performing ser...

Removal and replacement procedures 26 • Remove the server from the rack (on page 27 ). If the rack environment, cabling configuration, or the server location in the rack creates awkward conditions, remove the server from the rack. • Remove the access panel (on page 28 ). If you are servicing interna...

Removal and replacement procedures 27 2. Extend the server on the rack rails until the server rail-release latches engage. 3. After performing the installation or maintenance procedure, slide the server into the rack by pressing the server rail-release latches. Remove the server from the rack WARNIN...

Removal and replacement procedures 28 2. Remove the following components to reduce the weight of the server: o Processor memory drawer (" Remove the processor memory drawer " on page 29 ) o Hard drives (" SAS/SATA hard drive " on page 30 ) o Power supplies (" Hot-plug power suppl...

Removal and replacement procedures 30 To replace the component, reverse the removal procedure. Remove the SPI board To remove the component: 1. Power off the server. 2. Extend the server from the rack (on page 26 ). 3. Remove the access panel (on page 28 ). 4. Disconnect all cables from the SPI boar...

Removal and replacement procedures 31 3. Remove the hard drive. To replace the component, reverse the removal procedure. Heatsink To remove the component: 1. Power down the server (on page 26 ). 2. Remove the processor memory drawer shipping screws, if installed. Retain the screws for future use (&#...

Removal and replacement procedures 33 2. Remove the heatsink protective cover. 3. Install the heatsink. 4. Close and lock the processor retaining bracket. 5. Install the processor memory drawer cover. 6. Install the processor memory drawer. 7. Power up the server. Processor

Removal and replacement procedures 40 6. Apply all the grease to the top of the processor in the following pattern to ensure even distribution. 7. Install the heatsink. 8. Close and lock the processor retaining bracket. 9. Install the processor memory drawer cover. 10. Install the processor memory d...

Removal and replacement procedures 43 b. Install the DIMM. 2. Close the memory cartridge cover. 3. Install the memory cartridge. 4. Install the processor memory drawer cover. 5. Install the processor memory drawer. 6. Power up the server. DIMMs To remove the component: 1. Power down the server (on p...

Removal and replacement procedures 47 Power supply blank Remove the component as indicated. To replace the component, reverse the removal procedure. Hot-plug power supply The server supports up to four hot-plug power supplies. Install all power supplies to provide full redundancy. HP recommends inst...

Removal and replacement procedures 48 2. Remove the failed power supply. To replace the component, reverse the removal procedure. Systems Insight Display assembly CAUTION: When routing cables, always be sure that the cables are not in a position where they can be pinched or crimped. To remove the co...

Removal and replacement procedures 53 3. Remove the access panel (on page 28 ). 4. Disconnect the cable from the rear of the DVD-ROM drive. 5. Remove the DVD-ROM drive. To replace the component, reverse the removal procedure. Solid state drive To remove the component: 1. Power down the server (on pa...

Removal and replacement procedures 54 To replace the component, reverse the removal procedure. Expansion slot cover CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all expansion slots have either an expansion slot cover or an expansion board installed. 1. Po...

Removal and replacement procedures 56 7. Remove the expansion board. To replace the component, reverse the removal procedure. Battery-backed write cache procedures Two types of procedures are provided for the BBWC option: • Removal and replacement of failed components: o Removing the cache module (&...

Removal and replacement procedures 57 4. If the existing cache is connected to a battery, observe the BBWC Status LED (" Battery pack LEDs " on page 85 ). o If the LED is flashing every 2 seconds, data is still trapped in the cache. Restore system power, and then repeat the previous steps. o...

Removal and replacement procedures 58 o If the LED is not illuminated, disconnect the battery cable from the cache. 5. Disconnect the cable. 6. Remove the battery pack. The SPI board is removed for clarity. To replace the component, reverse the removal procedure. Recovering data from the battery-bac...

Removal and replacement procedures 59 o If the server has failed, remove the controller, cache module (" Removing the BBWC cache module " on page 56 ), and battery pack (" Removing the BBWC battery pack " on page 57 ) from the failed server, and install the controller, cache module, ...

Removal and replacement procedures 60 5. Disconnect the cable. 6. Remove the SPI board (on page 30 ). 7. Open the cache slot latches. 8. Remove the cache module. To replace the component, reverse the removal procedure. Removing the FBWC capacitor pack CAUTION: After the server is powered down, wait ...

Removal and replacement procedures 62 Battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an al...

Removal and replacement procedures 65 SAS backplane To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 26 ). 3. Remove the access panel (on page 28 ). 4. Remove all hard drives (" SAS/SATA hard drive " on page 30 ). 5. Disconnect all ...

Removal and replacement procedures 66 8. Remove the backplane. To replace the component, reverse the removal procedure. HP Trusted Platform Module The TPM is not a customer-removable part. CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security riv...

Diagnostic tools 67 Diagnostic tools Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software main...

Diagnostic tools 68 support ProLiant BL, ML, DL, and SL servers. The toolkit includes a modular set of utilities and important documentation that describes how to apply these tools to build an automated server deployment process. The Scripting Toolkit provides a flexible way to create standard serve...

Diagnostic tools 69 For more information about the controller and its features, see the HP Smart Array Controllers for HP ProLiant Servers User Guide on the HP website

Diagnostic tools 70 For more information, see the Management CD or DVD in the HP Insight Foundation suite for ProLiant. Insight Lights-Out 3 technology The iLO 3 subsystem is a standard component of selected ProLiant servers that provides server health and remote server manageability. The iLO 3 subs...

Diagnostic tools 71 HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and other related data needed for effective server management. Available in Microsoft® Windows® and Linux versions, the utility helps to ensure proper system operation. For more in...

Component identification 72 Component identification Front panel components Item Description 1 Serial and PID tag 2 Optical drive 3 Systems Insight Display 4 USB connectors (2) 5 Video connector 6 Processor memory drawer

Component identification 73 Front panel LEDs and buttons Item Description Status 1 UID button and LED Blue—Activated Blue (flashing)—Server being managed remotely Off—Deactivated 2 Health LED Green—Normal (system on) Amber (flashing)—Internal system health degraded Red (flashing)—Internal system hea...

Component identification 74 Systems Insight Display The Systems Insight Display LEDs represent the server and component layout. LED Description AMP status Off—No protection Green—Protection enabled Amber—Memory failure occurred Amber (flashing)—Memory configuration error Health Green—Normal (system ...

Component identification 75 Rear panel components Item Description Item Description 1 Power supply bay 4 (optional) 15 Expansion slot 2 (optional) 2 Power supply bay 3 (optional) 16 Expansion slot 3 (optional) 3 Power supply bay 2 17 Expansion slot 4 (optional) 4 Power supply bay 1 18 Expansion slot...

Component identification 76 Rear panel LEDs and buttons Item Description LED color Status 1 iLO 3 NIC Activity LED Green On or flashing—Network activity Off—No network activity 2 iLO 3 NIC Link LED Green On—Linked to network Off—Not linked to network 3 NIC 2 Activity LED Green On or flashing—Network...

Component identification 77 Power supply LED Power LED Status Off No AC power to power supply units Green AC is present. Standby output is on, output is disabled. Green AC is present. Standby output is on, power supply DC output is on and OK. Off Power supply failure (includes overvoltage and overte...

Component identification 78 System board components Item Description 1 Optional I/O expansion board connectors: • PCI-X/PCI Express I/O expansion board • PCI Express I/O expansion board 2 Slot 7 PCIe2 x8 (4, 2, 1) 3 Slot 8 PCIe2 x8 (4, 2, 1) 4 Slot 9 PCIe2 x16 (8, 4, 2, 1) 5 Slot 10 PCIe2 x8 (4, 2, ...

Component identification 79 System maintenance switch The system maintenance switch (SW1) is an eight-position switch that is used for system configuration. The default position for all eight positions is Off. Position Description Function S1 iLO 3 security Off = iLO 3 security is enabled. On = iLO ...

Component identification 80 SPI board components Item Description 1 Mini-SAS connectors (2) 2 SAS cache connector 3 TPM connector 4 Fan data connector 5 RMII connector 6 SD card slot 7 Battery 8 10Gb NIC connector* 9 NIC cache connector* 10 NIC 3 connector 11 NIC 1 connector 12 Video connector 13 Ke...

Component identification 81 I/O expansion board components • PCI-X/PCI Express I/O expansion board Item Description 1 Slot 6 PCIe2 x16 (16, 8, 4, 2, 1) 2 Slot 4 PCIe2 x8 (4, 2, 1)* 3 Slot 3 PCIe2 x16 (16, 8, 4, 2, 1) 4 Slot 2 PCI-X 5 Slot 1 PCI-X *Slot 4 is physically a x8 slot but operates electric...

Component identification 82 **Slots 2, 3, 5 and 6 are physically x16 slots but operate electrically as x8 slots. Processors and memory cartridges The processor memory drawer contains 4 processor sockets and 8 memory cartridges. For DIMM numbering and installation guidelines, see the server user guid...

Component identification 83 DIMM slot locations Each memory module contains 8 DIMM slots. The paired banks are identified by the letters A through D. Device numbers

Component identification 84 Hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (green) Hard drive LED combinations Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation On, off, or flashing Alternating amber and blue The drive has failed, or a predictive failu...

Component identification 88 Fan locations Power supply backplane components

Specifications 91 Specifications Environmental specifications Specification Value Temperature range* Operating 10 ° C to 35 ° C (50 ° F to 95 ° F) Shipping -40 ° C to 70 ° C (-40 ° F to 158 ° F) Maximum wet bulb temperature 28 ° C (82.4 ° F) Relative humidity (noncondensing)** Operating 10% to 90% N...

Acronyms and abbreviations 92 Acronyms and abbreviations ABEND abnormal end ASR Automatic Server Recovery BBWC battery-backed write cache FBWC flash-backed write cache iLO 3 Integrated Lights-Out 3 IML Integrated Management Log NVRAM nonvolatile memory ORCA Option ROM Configuration for Arrays PCIe p...

Documentation feedback 94 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback

Index 95 A access panel 28 ASR (Automatic Server Recovery) 70 Automatic Server Recovery (ASR) 70 B backplane, hard drive 65 backplane, power 65 backplane, SAS 65 battery 19, 62, 80 battery pack LEDs 85 battery-backed write cache (BBWC) 19, 56, 57, 58, 80, 85 battery-backed write cache battery pack 1...