HP 3400cl - Manual
HP 3400cl – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Quick Install Guide; Your Free Introduction to Proactive Networking!
- Page 3 – Software Updates Are; Free; Latest software; Software revision
- Page 4 – Mini-GBIC Operation Notes; write memory; . As a result, those devices may not connect; Auto; At a minimum, make sure the configurations match
1
Read Me First
for the ProCurve Series 3400cl Switches – Software Version M.08.75 or
greater
Contents
Module Hot Plug Operation Notes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1
Fiber Optic Transceiver Operating Temperature Variance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1
About Your ProCurve Series 3400cl Switch Manual Set
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2
View or Download the Software Manual Set
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2
Your
Free
Introduction to Proactive Networking!
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 2
Software Updates Are
Free
!
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 3
Saving the Configuration After Installing or Exchanging a Module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 3
Mini-GBIC Operation Notes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
Module Hot Plug/Swap Operation Notes
The Series 3400cl Switches do not support hot plugging or hot swapping of the switch cl modules. If you install
or remove modules after the switch has been powered on, a switch reset will occur. Installing or removing
modules should only be done during scheduled downtime.
However, hot swapping of the tranceivers is supported. You can install or remove transceivers with the switch
powered on.
For more information see the
ProCurve Switch cl Modules Installation Guide
.
Fiber Optic Transceiver Operating Temperature Variance
The fiber optic transceivers are rated at a lower operating temperature (
0
°
C to 40
°
C (32
°
F to 104
°
F)),
than
the 6400cl/3400cl switches or the cl modules (
0
°
C to 55
°
C (32
°
F to 131
°
F))
. Therefore when either
transceiver is installed in a cl module or in a 6410cl Switch it lowers the temperature rating of the
module and the switch the module is installed in to equal the rating of the transceiver.
3400_cl_RMF.fm Page 1 Monday, April 7, 2008 4:03 PM
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 About Your ProCurve Series 3400cl Switch Manual Set The switch manual set includes the following: View or Download the Software Manual Set The printed Quick Install Guide shipped with your ProCurve product describes installing, minimally config- uring, and troubleshooting. For further software fea...
3 Software Updates Are Free ! ProCurve Networking provides free software updates on the ProCurve Web site for your Series 3400cl switch. To access the software updates, go to the ProCurve Web site at www.procurve.com , then click on Software updates to go to the “ProCurve Networking software updates...
Mini-GBIC Operation Notes Hot Swapping mini-GBICs. The Gigabit-SX, Gigabit-LX, and Gigabit-LH mini-GBICs that you can install in your ProCurve Switch can be “hot swapped”—removed and installed after the switch is receiving power. You should disconnect the network cables from the mini-GBICs before ho...
