HP 2311cm/2311f/2311x - Manual

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, be sure that the power source andconnection are appropriate for this monitor. For information on the correct power cord set to use withthe monitor, see Power Cord Set ...

3 Setting Up the Monitor Unpacking the Monitor 1. Unpack the monitor. Make sure all contents are included. Store the packing box. 2. Turn off the computer and other attached devices. 3. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placingthe monitor scre...

Connecting Monitor Cables CAUTION: Before connecting cables to the monitor, ensure that the computer and monitor are powered off. NOTE: When using a DVI, VGA, or HDMI signal, you must connect your audio output to external speakers. The video source is determined by the video cable used. The monitor ...

Connecting the DVI-D Video Cable (Select Models) Connect one end of the DVI-D video cable to the back of the monitor and the other end to the DVI-Dvideo connector on the computer. You can use this cable only if your computer has a DVI compliantgraphics card that is either integrated or installed. Th...

Getting HDMI Sound If you use HDMI to connect to a monitor model without speakers, you must activate HDMI sound byadjusting the setting in Microsoft Windows. If HDMI is not activated, you can not hear any sound. Toactivate HDMI sound on your computer: 1. Right-click on the volume icon in the Windows...

Installing the Cable Management Clip Install the cable management clip over the input cable and power cord to gather them togetherbehind the monitor. Figure 3-7 Installing the Cable management Clip High-Bandwidth Digital Content Protection (HDCP) select models Your monitor supports HDCP and can rece...

When the monitor is powered on, a Monitor Status message is displayed for five seconds and thepower source LED on the rear of the monitor is green. The message shows which input is the currentactive signal, the status of the auto-switch source setting (On or Off), the default source signal, thecurre...

Connecting External Speakers and Audio Cable (Select Models) Use the following procedure to connect the external speakers to a computer. 1. Turn the computer on. 2. Connect the audio cable to the audio-speaker connector on the computer, and then connect theUSB power cable to a USB connector on the c...

Wall Mounting the Monitor Panel To mount the monitor panel to an existing wall mounting device or swing arm, purchase an HPmounting accessory kit. Mounting devices can be purchased separately from HP. Visit www.hp.com/ support for ordering information. CAUTION: When handling the monitor, be careful ...

4 Operating the Monitor CD Software and Utilities The CD that is included with this monitor contains drivers and software that you can install on yourcomputer. Installing Drivers If you determine that you need to update the drivers, you can install the monitor driver INF and ICMfiles from the CD, or...

Icon Main Menu Options Sub-menu Options Description Auto-Switch Source Turns the automatic video signal input toOn or Off on the system. The factorydefault is On. Exit Exits the OSD menu screen. Identifying Monitor Conditions Special messages appear on the monitor screen for the following monitor co...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and therecommended solutions: Problem Solution Power button LED is not on. Make sure that the Power button is on, and the power cord is connected to a groundedpower outlet and t...

Getting Support from hp.com Before you contact customer service, refer to HP Technical Support at: www.hp.com/support Select your country/region, and then follow the links to the support page for your monitor. Preparing to Call Technical Support If you cannot solve a problem by using the troubleshoo...

B Technical Specifications All specifications represent the typical specifications provided by HP component manufacturers;performance might vary either higher or lower. HP LCD Monitors Table B-1 2011x/2011s Specifications Specifications Display Type: TFT LCD active matrix Viewable Image Size: 50.8 c...

Table B-5 2711x Specifications (continued) Specifications Power Source: 100-240 VAC (ca), 50/60 Hz Maximum Power Consumption: 35 watts (W) Typical Power Consumption: 28 watts (W) Sleep Power Consumption: <1 watts (W) Preset Video Modes The monitor automatically recognizes many preset video input ...

Table B-8 HDMI High Definition Factory Preset Video Modes (Select Models) Preset HD Video DisplayResolution Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 1 480p 720 x 480 31.469 60 2 720p60 1280 x 720 45 60 3 576p 720 x 576 31.25 50 4 720p50 1280 x 720 37.5 50 5 1080p60 1920 x 1080 67....

LCD Monitor Quality and Pixel Policy Your LCD monitor uses high-precision technology, manufactured according to high standards, to helpguarantee trouble-free performance. Nevertheless, the display might have cosmetic imperfectionsthat appear as small bright or dark spots. This is common to all LCD m...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a resid...

Hewlett Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800-HP-INVENT (1-800 474-6836) For questions regarding this FCC declaration, contact: Hewlett Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identi...

For non-telecommunications products and for EUharmonized telecommunications products, suchas Bluetooth® within power class below 10mW. For EU non-harmonized telecommunicationsproducts (If applicable, a 4-digit notified bodynumber is inserted between CE and !). Please refer to the regulatory label pr...

and current rating marked on the product. In addition, the cross-sectional area of the wire must be aminimum of 0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12feet (3.6 m). If you have questions about the type of power cord to use, contact an authorized HPservice...

Turkey EEE Regulation In Conformity with the EEE Regulation EEE Yönetmeli ğ ine Uygundur ENWW Product Environmental Notices 41