HP 170X - Manual - manualsarea.com

Page 5 - Contents; Product Overview

3 Contents 1 Product Overview Supported Printers, Plotters, and HP All-in-One Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Network Management . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Network Configuration . . . . . . . . . . . . . . . . . . . . . ...

Page 7 - Product Overview; at convenient locations directly on the

1-1 1 Product Overview This hardware guide covers the following Hewlett-Packard print servers: These print servers send data to printers at speeds of up to 360 kilobytes per second, which is as fast or faster than many internal print servers. The external print servers enhance workgroup capability b...

Page 8 - with a parallel

1-2 Product Overview The HP JetDirect 300X provides connectivity to 10Base-T and 100Base-TX networks. The HP JetDirect 170X provides connectivity to 10Base-T networks. The HP JetDirect EX Plus provides connectivity to 10Base-T and 10Base2 networks. The HP JetDirect three-port print servers have thre...

Page 9 - Quick Start Guide

Product Overview 1-3 Product Over view 1 Network Management The HP JetDirect external print servers support the Simple Network Management Protocol (SNMP), which enables remote printer management and troubleshooting. A standard SNMP agent resides on these print servers. Any standard SNMP-based applic...

Page 10 - Components and Features

1-4 Product Overview Components and Features HP JetDirect 300X (J3263A): ● Bidirectional parallel port (IEEE 1284). ● Network port (Ethernet or Fast Ethernet): RJ-45 for 10Base-T or 100Base-TX. ● Test button (sends print server configuration page). ● 2 LEDs on front indicate LAN activity/status. ● 2...

Page 12 - Transmission Media

1-6 Product Overview Transmission Media IEEE 802.3 Ethernet 10Base2 Thin coaxial cable with BNC connector. IEEE 802.3 Ethernet 10Base-T Four pairs of unshielded twisted-pair Category 3, 4, or 5 cable with RJ-45 connector.* IEEE 802.3 Fast Ethernet 100Base-TX Four pairs of unshielded twisted-pairCate...

Page 13 - Hardware Requirements

Product Overview 1-7 Product Over view 1 Hardware Requirements HP JetDirect 300X J3263A (Ethernet 10Base-T or 100Base-TX) HP JetDirect 170X J3258B (Ethernet 10Base-T) HP JetDirect EX Plus J2591A (Ethernet 10Base-T or 10Base2) HP JetDirect 500X J3265A (Ethernet 10Base-T, 100Base-TX, or 10Base2) J3264...

Page 14 - LEDs; On the top of the print server are Status and LAN Activity LEDs:

1-8 Product Overview LEDs On the top of the print server are Status and LAN Activity LEDs: Between the Status and LAN Activity LEDs is the Test button, used to print a configuration page. See Chapter 2 for more information. On the back of the HP JetDirect 300X (J3263A) and 500X (J3265A) Print Server...

Page 16 - -10 Product Overview

Page 17 - Hardware Installation; Generate a configuration page from the print server.

2-1 2 Hardware Installation To install the HP JetDirect external print servers, you need to complete these steps. ● Verify that your printer parallel port(s) work properly. ● Connect the print server to the network and printer(s) and plug in the print server. ● Generate a configuration page from the...

Page 18 - Note; must

2-2 Hardware Installation 4. For the 300X or 500X Ethernet print servers (J3263A or J3265A), verify that the auto-negotiation switches are in their default positions—all down. (For other options, see page 1-9.) Figure 2.2 Hardware connections using a U.S. power module for the HP JetDirect J3265A Pri...

Page 19 - Hardware Installation 2-3; Hardware; Plug the power module into the wall outlet; Verifying the Hardware Installation; To generate a configuration page, follow these steps:; Selecting a Configuration Page Language

Hardware Installation 2-3 Hardware Installation 2 8. Plug the power module into the wall outlet ➐ . Since there is no power switch, the print server is switched on after you plug it in. 9. Check the LEDs on the front of print server. The Status LED should be green—either steady or blinking. If the i...

Page 20 - -4 Hardware Installation; Resetting to Factory Defaults; Unplug the power cord from the print server.

2-4 Hardware Installation If you want to change the detected printer language, use the LEDs and Test button to select a PDL for the configuration page. When you hold down the Test button for three seconds, the LEDs begin to cycle through four configurations, as outlined in the following table. Relea...

Page 21 - Specifications; Physical Specifications

A-1 A Specifications Physical Specifications Product Number Width Height Depth* Weight J2591A 178 mm(7.0 in.) 31 mm(1.2 in.) 124 mm(4.9 in.) 269 g(0.59 lbs.) J3263A 178 mm(7.0 in.) 31 mm(1.2 in.) 112 mm(4.4 in.) 241 g(0.53 lbs.) J3264A 280 mm(11 in.) 31 mm(1.2 in.) 127 mm(5.0 in.) 454 g(1 lb.) J3265...

Page 22 - Power Requirements

A-2 Specifications Power Requirements Power Modules for J3264A and J3265A Note: If two parts are listed for one country/region, either part can be used. Country Part Num. Input Rating Output Rating Australia, New Zealand, Argentina 9100-5172 230-240VAC 50 Hz 13 VDC @625 ma 0950-3358 230-240VAC 50 Hz...

Page 24 - Environmental; Acoustic Noise; Not applicable; Electromagnetic Emissions; Products comply with:

A-4 Specifications Environmental Acoustic Noise Not applicable Electromagnetic Emissions FCC part 15 Class A (U.S.A.), ICES-003 (Canada), VCCI Class 1 (in Japan), CISPR-22/EN55022 Class A, CNS 13438 (Taiwan), AS/NZS 3548 (Australia/New Zealand), GOST 29216 (Russia) Note For EU compliance, see the De...

Page 25 - Regulatory Statements; European Community; This equipment complies with CISPR22/EN55022 Class A.

B-1 B Regulatory Statements FCC Statement (U.S.A) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a...

Page 26 - B-2 Regulatory Statements; Declaration of Conformity

B-2 Regulatory Statements Declaration of Conformity The following Declaration complies with ISO/IEC Guide 22 and EN 45014. It identifies the product, the manufacturer's name and address, and applicable specifications recognized in the European community.

Page 27 - Regulatory Statements B-3; Regulatory; This equipment complies with Australian EMC

Regulatory Statements B-3 Regulatory Statements B Australia. This equipment complies with Australian EMC requirements. Canada. Complies with Canadian EMC Class-A requirements. Japan: VCCI Class 1. Korea: RRL Statement. Taiwan: Class A.

Page 28 - B-4 Regulatory Statements; Chinese Safety Statement:

B-4 Regulatory Statements Chinese Safety Statement: