Honeywell VISTA-10PSIA - Manual

Honeywell VISTA-10PSIA

Honeywell VISTA-10PSIA – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
72 Page 72
Page: / 72

Table of Contents:

  • Page 2 – RECOMMENDATIONS FOR PROPER PROTECTION; Devices Help Provide Proper Coverage for the Protected Premises.; The installation of smoke detectors in kitchens, attics; Recommendations For Proper Intrusion Protection; ii
  • Page 3 – Table Of Contents; iii
  • Page 4 – Zone Programming Overview (
  • Page 5 – S E C T I O N 1; Features and Installation Highlights; Capabilities; Up to 16 security codes, each with separate authority levels; Functions; dedicated key on keypads to send a signal to the pager; Compatible Devices; Supports 5881 series receiver and 5800 series transmitters
  • Page 6 – Important Installation Highlights (Installer Please Read); 204 Relay Modules must be set for specific address 12 (see
  • Page 7 – S E C T I O N 2; Mounting and Wiring the Control; Cabinet and Lock; Figure 1. Installing the Cabinet Lock; Mounting the PC Board Alone; NOTES; Figure 2. Mounting the PC Board
  • Page 8 – Mounting Board with RF Receiver; accompanying screws.; transmissions from wireless transmitters.; Figure 3. Mounting the PC Board and RF Receiver
  • Page 9 – Wiring to Keypads; starting at address 16; The; first keypad is address 16; enabled and set with all sounds on.; UL; case of AC power loss.
  • Page 10 – Use only UL Listed sounding devices for UL installations.; Wiring the AC Transformer; Wire Size; Up to 50 feet; Backup Battery; required to meet the mandatory standby time.; Installation Instructions
  • Page 11 – Earth Ground; Metal Cold Water Pipe:; AUXILIARY DEVICE CURRENT DRAW WORKSHEET
  • Page 12 – Hardwire Zones; Normally Open Zones/ Normally Open EOLR Zones; For UL commercial burglar alarm installations, use EOLR zones.; Smoke Detectors; -Wire Smoke Detectors; Figure 7. 4-Wire Smoke Detector Connections
  • Page 13 – Installing the RF Receiver; RF Receiver No. of Zones; Installing a 5800TM Module
  • Page 14 – Installing the Transmitters; perform a Go/No Go Test, described in the; Fire zones (Zone Type 9 and 16) and 12 hours for all other zone types.; Refer to the table of compatible devices at the back of this manual.; Transmitter Battery Life; • See Wireless Transmitter paragraph in the; Installing a Keyswitch; 000 ohm EOL resistor if connected across the selected zone.; Output Device
  • Page 15 – Figure 10. Keyswitch Wiring Connections; Connecting Relay Modules; standard 4-conductor twisted cable for long wiring runs.; CHECK xx Wire Expansion
  • Page 16 – If on-board triggers are used, the wiring between; On-Board Trigger Connector with 4-Wire Cable; Phone Line/Phone Module Connections; Audio Alarm Verification
  • Page 17 – Phone Module Problems; Long Range Radio Connections
  • Page 18 – Connections use one of the on-board triggers.
  • Page 19 – S E C T I O N 3; Programming Overview; About Programming; Programming Mode...; Keypads; Address Keypad
  • Page 20 – Pager Programming; command; (see Security Codes, Assigning Attributes in; Function Keys
  • Page 21 – Zone Type Definitions; Zone Type
  • Page 23 – Mechanics of Programming; Data Field Programming Procedures; Task Procedure; Menu Mode Programming (
  • Page 24 – Table of Device Addresses
  • Page 25 – S E C T I O N 4; Data Field Programming; About Data Field Programming; Programming Guide; Programming Data Fields; Reduction. Fields unique to the; System Setup Fields; FIELD; disarm; be entered, and the keypad set to
  • Page 26 – Zone Sounds & Timing; Feature always enabled field does not exist.
  • Page 27 – Dialer Programming; = use delay set in entry 1
  • Page 28 – System Status Report Codes; Zone report codes are programmed using interactive; ADEMCO Contact ID® Reporting:
  • Page 29 – Enter appropriate report code.; Always enabled. Field does not apply to other controls.
  • Page 30 – Miscellaneous System Fields; Use this menu mode to assign alpha descriptors to zones.; is not; Select whether “; ALARM CANCELED; is displayed on the LCD keypad under the following conditions:; before; dialer delay expires message “Alarm Canceled” is not displayed.
  • Page 31 – Call Waiting Disable:; = call waiting not used; only once; during an armed period.; Unlimited Reports Enable:; = restrict reports to the setting in entry 1
  • Page 32 – Pager Programming Fields
  • Page 33 – Configurable Zone Type Programming Fields; System Communication; Configurable Zone Type Options
  • Page 34 – Configurable Zone Type Charts; Zone Conditions Represented
  • Page 35 – Keypad Programming Fields
  • Page 37 – S E C T I O N 5; Menu Mode Programming; Alpha Descriptor Programming); 6 Zone Programming Procedure; PROMPT; SET; We
  • Page 38 – ] key to move to the “L” position, then enter the loop number (see Loop
  • Page 39 – Do; 8 Expert Programming Mode Procedures; Start Expert Programming mode by pressing; Zn
  • Page 40 – Wireless Key Programming Templates; This procedure programs the wireless keys,; but a key is not active for arming/disarming until; System Operation; To quit this mode
  • Page 41 – Wireless Key Predefined Default Templates; 804 Wireless Key Transmitter; 804BD 2-Way Wireless Key Transmitter
  • Page 42 – the relay module’s device address and the relay position on; Relays are not recommended for life safety applications.; MENU NAVIGATION NOTE:; ] key to accept an entry and; Output Device programming involves:; You must map output devices using *79 Menu Mode
  • Page 43 – *80 Menu Mode: Defining Output Functions; Output Definition Components; Component Description; A reference number that defines an output’s characteristics.; Prompt Entry; Output Action; 1 A E Trig
  • Page 44 – 1 Enter Zn type; 1 Output Action
  • Page 45 – Used for...; Zone List Programming; Enter each zone number followed by [; IMPORTANT; To delete a zone or zones in a zone list enter 1 to continue.
  • Page 46 – Start Function Key Programming mode by pressing; Press Key to Pgm
  • Page 47 – About Descriptor Programming Overview (; You can enter zone descriptors when the zone is being defined in; boldface type; . The phone module will not provide annunciation of the other words.; boldface; in the; Programming Zone Descriptors (Menu mode; When defining descriptors:; P r o g r a m A l p h a ?
  • Page 48 – Summary Screen; ten; Do not assign reminder words if using fixed-word keypads.; A cursor appears at the beginning of the second line.
  • Page 49 – ALPHA VOCABULARY LIST; Italicized
  • Page 50 – Programming Installer and User Schedules; ] to continue to the “Start” prompt
  • Page 51 – Enter the event’s start time and days of the week to occur.; Enter the desired repeat option for this schedule.
  • Page 53 – S E C T I O N 6; System Communication and Operation; System Communication Overview; FORMAT; FORMAT TYPE
  • Page 55 – Ademco Contact ID; TABLE OF CONTACT ID EVENT CODES; Code
  • Page 56 – User Security Codes; Authority Levels; Level User; Wireless Key Templates; Setting the Real-Time Clock; A cursor appears under the first digit of the hour.
  • Page 57 – Keypad Functions; Voice Keypads; The 6150V/6160V Voice Keypads provide the following features:; Keypad Commands; Function Description; SUMMARY OF ARMING MODES
  • Page 58 – Panic Keys; Keys; For a Silent panic function (if programmed) to be of; Various System Trouble Displays; Alpha Display; Bell Failure
  • Page 59 – S E C T I O N 7; Testing the System; About Test Procedures; ] to display the faulted; TEST; The following will be displayed:; A Contact ID report will also be sent (code 607); Checking Transmitter Enrollment (Sniffer Mode); As the system receives a signal from
  • Page 60 – When; one; Usually a few inches in either direction is all that is required.; Dialer Communication Test and Periodic Test Reports; If the dialer test is unsuccessful, the following is displayed:; Enter Installer code + OFF to clear the display and exit.; Automatic Periodic Test Report; entering the test report schedule command.; Automatic Standby Battery Tests
  • Page 61 – S E C T I O N 8; Specifications & Accessories; SECURITY CONTROL; not; connect two 702s in parallel.; : For UL installations, Alarm Sounder plus Auxiliary; Maximum Zone Resistance:; Zones 1–8 = 300 ohms excluding EOLR standard zones; COMPATIBLE DEVICES; 800TM Transmitter Module (used with 5827BD W ireless 2-W ay Keypad); Long Range Radio
  • Page 62 – 800 Series Transmitter Input Loop Identification; The following transmitters are; Compatible 5800 Series Transmitters Table; Model Product
  • Page 63 – Compatible 5800 Series Transmitters Table (continued)
  • Page 65 – S E C T I O N 9; Regulatory Agency Statements; RADIO FREQUENCY EMISSIONS; Federal Communications Commission (FCC) Part 15; TELEPHONE/MODEM INTERFACE; Industry Canada; Ringer Equivalence Number Notice:; Industrie Canada
  • Page 66 – UL NOTICES; 6) cannot be greater than 30 seconds for UL Residential; SIA Quick Reference Guide
  • Page 67 – S E C T I O N 1 0; Limitations and Warranty; WARNING; bypass an alarm sensor or disconnect an alarm warning device.
  • Page 69 – – INDEX –
  • Page 71 – SUMMARY OF CONNECTIONS; Figure 17. Summary of Connections
  • Page 72 – LIMITED WARRANTY; or other events
Loading the manual

ADEMCO VISTA-10P

ADEMCO VISTA-10PSIA

Security Systems

Installation and Setup Guide














K0735V3 10/04 Rev. B

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - RECOMMENDATIONS FOR PROPER PROTECTION; Devices Help Provide Proper Coverage for the Protected Premises.; The installation of smoke detectors in kitchens, attics; Recommendations For Proper Intrusion Protection; ii

RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscr...

Page 3 - Table Of Contents; iii

Table Of Contents • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Features and Installation Highlights ...............................................................................................1-1 Capabilities ..................................................................

Page 4 - Zone Programming Overview (

Table Of Contents • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Menu Mode Programming...................................................................................................................5-1 Zone Programming Overview ( ∗ 56 and ∗ 58 Menu Modes) .....................

Other Honeywell Models