Page 2 - Disclaimer; © 2004 - 2011 Honeywell International Inc. All rights reserved.; Trademarks
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this pub...
Page 3 - iii; Table of Contents; Important Notes; Single or Dual Cable Scale Configuration Bar Codes; Scanner Configuration Bar Codes; Dual Cable Scanner Configuration Bar Codes
iii Table of Contents Important Notes Before You Start ............................................................................................ 1 Scale Program Mode .......................................................................................... 3 Scale/Load Cell Configuration Bar Code...
Page 4 - iv; Additional POS Data Formatting
iv Retalix / NCR ....................................................................................... 29 IT Retail ................................................................................................ 30 IBM Self Checkout System ............................................................
Page 5 - EAS Bar Codes; Scanner Test Bar Codes; Supplemental Tests; Customer Support
v EAS Bar Codes EAS Device Types ............................................................................... 63 EAS Timeout ........................................................................................ 66 EAS Connection ....................................................................
Page 6 - vi
Page 7 - Before You Start; All of the bar codes in this manual require:; The scanner/scale to have a firmware number of 14996 or higher; Scale Operation: Calibration
1 Important Notes Before You Start It is important to read the text at the top of each page of bar codes. The text will provide important additional information about the restrictions and uses of the bar codes shown. Not all configuration codes are designed to be used for both a single and dual cabl...
Page 9 - Scale Program Mode; Power down
3 Scale Program Mode The following steps are only required for the scale configuration bar codes located on pages 7 - 21 (bar codes beginning with 996.) 1. Power down the scanner/scale. Then, temporarily remove the scale platter and place it in a safe location. See caution on page 4. Figure 1. 2. Cu...
Page 10 - Disconnect; the; Reinstall; the platter and connect AC power to the scanner.
4 Figure 3. StratosS Calibration Seal and Switch Location 5. Disconnect the scale-to-host RS232 cable from the unit ( dual cable interface only.) Figure 4. Disconnect scale-to-host RS232 Cable 6. Reinstall the platter and connect AC power to the scanner. Note : Check the AC input requirements of the...
Page 11 - scan; the desired; scale; the scale-to-host RS232 cable to the scanner
5 7. If the system is equipped with a remote scale display, it will read H - - -. 8. Use the vertical window to scan the desired scale configuration bar codes , located on pages 7 - 21. Figure 5. 9. Reconnect the scale-to-host RS232 cable to the scanner (dual cable interface only.) Figure 6. 10. The...
Page 13 - Unit Configuration (Pounds or Kilograms); The following bar codes can be used to configure a; Single or Dual Cable; be in scale program mode to use these bar codes.; pounds; Scale; kilograms
7 Scale/Load Cell Configuration Bar Codes Single or Dual Cable Scale Configuration Bar Codes Unit Configuration (Pounds or Kilograms) The following bar codes can be used to configure a Single or Dual Cable MS2xx0. The MS2xx0 must be in scale program mode to use these bar codes. Scale = Pounds ³ 9 9 ...
Page 14 - Pole Display Configuration; Scale 46xx to Display
8 Pole Display Configuration The following bar codes can be used to configure a Single or Dual Cable MS2xx0. The MS2xx0 must be in scale program mode to use these bar codes. Scale Has Display ³ 9 9 6 0 0 3 Set the scale to use a remote display to show all scale activity. A remote display must be plu...
Page 15 - Scale Settling Filter Configuration; The following bar code can be used to configure a; be in scale program mode to use this bar code.
9 Scale Settling Filter Configuration The following bar code can be used to configure a Single or Dual Cable MS2xx0. The MS2xx0 must be in scale program mode to use this bar code. The scale’s filter setting allows the unit to withstand a certain amount of vibration from the checkout counter. A stron...
Page 17 - Scroll Weight Configuration
11 Scroll Weight Configuration The following bar codes can be used to configure a Single or Dual Cable MS2xx0. The MS2xx0 must be in scale program mode to use these bar codes. These bar codes only affect the pole display. Scale = Scroll Settling Weight ³ 9 9 6 0 1 0 Scroll the weight on the display ...
Page 18 - Dual Cable Scale Configuration Bar Codes; Price Computing Configuration; The following bar codes are only used when the scale is in; Dual Cable
12 Dual Cable Scale Configuration Bar Codes Price Computing Configuration The following bar codes are only used when the scale is in Dual Cable mode. The MS2xx0 must be in scale program mode to use these bar codes. * Scale = No Price Computing ³ 9 9 6 0 0 8 Scale is not the price computing type. * F...
Page 19 - Scale Protocols; scanner
13 Scale Protocols The following bar codes will change scale parameters intended for a Dual Cable environment. To place the scanner in Dual Cable mode, please refer to page 23. The MS2xx0 must be in scale program mode to use these bar codes. Scale = EPOS Protocol ³ 9 9 6 0 1 3 Set the scale RS232 pr...
Page 22 - after; Scale Protocol; must
16 COM Port Settings (Baud Rate) The following bar codes will change scale parameters intended for a Dual Cable environment. If a Scale Protocol bar code from page 13 or 15 is used, the bar codes below must be scanned after the Scale Protocol bar code in order to be effective. The MS2xx0 must be in ...
Page 27 - Single Cable Scale Configuration Bar Codes; Set Scale for Single Cable Communication
21 Single Cable Scale Configuration Bar Codes Set Scale for Single Cable Communication The MS2xx0 must be in scale program mode to use this bar code. If your application requires single cable communication, scan the following bar code to set the scale configuration to the single cable defaults as re...
Page 29 - Dual Cable Scanner Mode; No Scale
23 Scanner Configuration Bar Codes Dual Cable Scanner Configuration Bar Codes Dual Cable Scanner Mode The following bar codes can be used to place, as well as configure, the scanner in Dual Cable mode. The MS2xx0 does not need to be in scale program mode to use the following bar codes. Scanner = Dua...
Page 30 - Various Dual Cable Scanner Mode
24 Various Dual Cable Scanner Mode The following bar codes can be used to configure a Dual Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. REWE ³ 9 9 7 0 1 0 Dual Cable RS232 - REWE Communication Port Settings: • 9600 Baud • 7 Data Bits • 2 Stop Bit • Sp...
Page 31 - Generation 46xx and IBM OEM Full Speed USB
25 IBM 3 rd Generation 46xx and IBM OEM Full Speed USB The following bar codes can be used to configure a Dual Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. IBM 3 rd Generation Communication ³ 9 9 9 9 5 2 When scanned the Stratos will operate as a tabl...
Page 32 - Single Cable Protocols for POS Compatibility; MSS Global; Single Cable
26 Single Cable Protocols for POS Compatibility MSS Global The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. MSS Global, English ³ 9 9 9 9 5 1 Scanner/Scale, Single Cable RS232 MSS Global Retail, En...
Page 34 - OPOS
28 OPOS The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. OPOS, English ³ 9 9 9 9 5 8 Scanner/Scale Single Cable RS232 OPOS, English Scale Defaults Communication Port Settings: • 9600 Baud • 8 Data ...
Page 36 - IT Retail
30 IT Retail The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. IT Retail, English ³ 9 9 7 0 0 8 Scanner/Scale Single Cable RS232 IT Retail, English Communication Port Settings: • 9600 Baud • 7 Data ...
Page 37 - IBM Self Checkout System
31 IBM Self Checkout System The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. IBM Self Checkout System, English ³ 9 9 7 0 2 0 Scanner/Scale Single Cable RS232 - IBM Self Checkout System, English Com...
Page 38 - Various RS232 Single Cable Codes
32 Various RS232 Single Cable Codes The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. Morrison’s Tec Metric ³ 9 9 7 0 2 3 Scanner/Scale Single Cable RS232 – Morrison’s with Tec Display, Metric Commu...
Page 39 - Generation 46xx; The following codes; do not; require that the MS2xx0 to be in scale program; English; Metric
33 IBM 3 rd Generation 46xx The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. IBM 3 rd Generation 46xx, English † ³ 9 9 9 9 6 0 Scanner/Scale Single Cable IBM 46xx † , RS485, English (lbs.) † Termin...
Page 40 - IBM OEM Full Speed USB; Single
34 IBM OEM Full Speed USB The following bar codes can be used to configure a Single Cable MS2xx0. The following codes do not require that the MS2xx0 to be in scale program mode. IBM OEM Full Speed USB, English ³ 9 9 9 9 6 2 Table Top Scanner/Scale Single Cable , IBM OEM Full Speed USB, 4-Digit Weigh...
Page 41 - Full Speed USB Table Top/Handheld
35 Additional POS Data Formatting Full Speed USB Table Top/Handheld The following codes do not require that the MS2xx0 to be in scale program mode. Scanner 4B Handheld ³ 3 1 6 4 3 0 Full Speed USB interface to 4B00h handheld usage. Scanner 4A Flatbed ³ 3 1 6 4 1 0 Full Speed USB interface to 4A00h t...
Page 43 - Special Function ACK; * Factory Default Setting
37 Special Function ACK The following codes do not require that the MS2xx0 to be in scale program mode. Enable Special Function ACK Answer ³ 1 4 1 7 1 4 Answer simple special functions with ACK. * Disable Special Function ACK ³ 1 4 1 7 0 4 * Factory Default Setting
Page 45 - x-30 Acknowledge Responses; inhibit; all ‘simple
39 3x-30 Acknowledge Responses The following codes do not require that the MS2xx0 to be in scale program mode. No 3x-30 Answer ³ 1 4 1 7 1 0 This bar code will inhibit all ‘simple acknowledge’ (3x-30) answers to POS or OPOS commands. * 3x-30 Answer ³ 1 4 1 7 0 0 The scanner will answer all NCR and O...
Page 46 - Special Function Command Responses
40 Special Function Command Responses The following codes do not require that the MS2xx0 to be in scale program mode. Spec Func Ans 3x30 ³ 1 4 1 9 1 4 Answer Special Function commands in the 3x-30 format as opposed to the Ack / Nak which is the norm. * Spec Func Ans Ack ³ 1 4 1 9 0 4 Answer Special ...
Page 50 - BCC in POS communications
44 BCC in POS communications The following codes do not require that the MS2xx0 to be in scale program mode. Skip BCC in messages ³ 1 4 1 4 1 0 This bar code will tell the scanner to NOT expect or transmit the Block Check Character in all message transmissions. * Add BCC in messages ³ 1 4 1 4 0 0 Th...
Page 51 - Scale Status Bytes
45 3 Scale Status Bytes The following codes do not require that the MS2xx0 to be in scale program mode. Enable 3 Scale Status Bytes ³ 1 2 4 8 1 3 Required for applications where the host system display is the primary scale display and there is no remote pole display connected directly to the scanner...
Page 52 - Scale Options
46 Scale Options The following codes do not require that the MS2xx0 to be in scale program mode. 5-Digit Weight ³ 1 4 1 0 1 0 Sets the English Mode weight to 5-digits, as in xx.yyy pounds. In order to work properly, this bar code must be scanned AFTER scanning one of the English configuration bar co...
Page 53 - Remote Display; No Remote Display; scanner’s
47 Remote Display The following codes do not require that the MS2xx0 to be in scale program mode. No Remote Display ³ 1 4 0 9 0 2 When no remote display is installed, scan the No Remote Display bar code AFTER scanning one of the configuration bar codes found on pages 26 - 34 to remove the scale’s di...
Page 54 - StratosSTATS
48 StratosSTATS The following codes do not require that the MS2xx0 to be in scale program mode. Activate StratosSTATS ³ 9 9 7 0 1 7 This bar code sets: • StratosSTATS bar code data formatting active. • Bar code Attempt Interval to 0.5 seconds. • Time to find supplements (code 128) to 0.3 seconds. Us...
Page 56 - Do not; scan these bar codes unless instructed by a customer service
50 StratosSTATS The following codes do not require that the MS2xx0 to be in scale program mode. Do not scan these bar codes unless instructed by a customer service representative. Dual Xmit Carriage Return ³ 1 3 8 5 1 2 This bar code enables a secondary carriage return suffix to be used only for the...
Page 57 - Additional POS Related Functions; Scanner Beep on Weight Sent
51 Additional POS Related Functions Scanner Beep on Weight Sent The following codes do not require that the MS2xx0 to be in scale program mode. Beep on Weight ³ 1 4 1 9 1 7 Request scanner beep when a successful weight is sent. This code should only be used for ‘weight on demand’ applications. If us...
Page 58 - Restrict In-Store Codes
52 Restrict In-Store Codes The following codes do not require that the MS2xx0 to be in scale program mode. Restrict In-Store Codes ³ 1 2 5 8 1 0 This bar code places tighter restrictions on in-store codes. These codes are: EAN13 Sys2 UPCA Sys2 and Sys4 * No Restrict In-Store Codes ³ 1 2 5 8 0 0 Disa...
Page 59 - Scale Shadow Mode
53 Scale Shadow Mode The following codes do not require that the MS2xx0 to be in scale program mode. Scale Shadow Mode ³ 1 4 2 2 1 7 This bar code sets the scale to the highest priority to allow for frequent scale - POS commands. This bar code is only to be used in single cable scale mode. * No Scal...
Page 61 - Additional Scanner Configuration Bar Codes; Horizontal Depth of Field
55 Additional Scanner Configuration Bar Codes Horizontal Depth of Field The following codes do not require that the MS2xx0 to be in scale program mode. Do not scan these bar codes unless instructed by a customer service representative. * Horizontal High DOF ³ 2 1 8 7 0 2 This bar code sets the DOF f...
Page 63 - Vertical Depth of Field
57 Vertical Depth of Field The following codes do not require that the MS2xx0 to be in scale program mode. Do not scan these bar codes unless instructed by a customer service representative. * Vertical High DOF ³ 2 1 8 7 0 0 This bar code sets the DOF for the vertical laser channels to High DOF, whi...
Page 65 - Auxiliary Port; StratosSCHOOLTM
59 Auxiliary Port StratosSCHOOL™ The following codes do not require that the MS2xx0 to be in scale program mode. Auxiliary History Report ³ 9 9 7 0 1 1 The Auxiliary port may be used to download or clear data to Stratos SCHOOL ™. The two commands that can be used are Upload Scanner Data and Clear Sc...
Page 66 - Quick Start for a Secondary Honeywell Scanner; Note
60 Quick Start for a Secondary Honeywell Scanner The following codes do not require that the MS2xx0 to be in scale program mode. Step 1 Use the Stratos to scan the following bar codes. These bar codes will configure the Stratos’ auxiliary port to accept a Honeywell scanner as the secondary scanner. ...
Page 68 - Configuration sequence continued from previous page.
62 Quick Start for a Secondary Honeywell Scanner Configuration sequence continued from previous page. Disable LF Suffix ³ 1 1 6 6 0 2 Exit Configuration Mode ³ 9 9 9 9 9 9
Page 69 - EAS Device Types
63 EAS Bar Codes EAS Device Types The following codes do not require that the MS2xx0 to be in scale program mode. * No EAS Device ³ 3 3 7 2 0 0 No EAS device is connected. * Factory Default Setting EAS Device Type 1 ³ 3 3 7 2 1 0 Sensormatic ScanMax Pro
Page 72 - EAS Timeout
66 EAS Timeout The following codes do not require that the MS2xx0 to be in scale program mode. * EAS = 0 seconds ³ 8 4 6 0 0 0 * Factory Default Setting EAS = 1 second ³ 8 4 6 0 0 1 0 0
Page 77 - EAS Connection
71 EAS Connection The following codes do not require that the MS2xx0 to be in scale program mode. * EAS Digital Aux Port ³ 1 4 6 1 0 0 The EAS signals use the RTS and CTS line of the Auxiliary RS232 In connector. * Factory Default Setting EAS Digital Host Port ³ 1 4 6 1 1 0 The EAS signals use the R...
Page 80 - Continuous Mode
74 Continuous Mode The following codes do not require that the MS2xx0 to be in scale program mode. EAS Continuous Mode ³ 1 4 6 1 1 5 When in continuous mode and the scanner is enabled, the EAS will always be online to deactivate an EAS tag. * EAS Interlock Mode ³ 1 4 6 1 0 5 This bar code establishe...
Page 81 - EAS Deactivation
75 EAS Deactivation The following codes do not require that the MS2xx0 to be in scale program mode. Blink Scan LED on Deactivation ³ 1 4 6 1 1 3 The scanner will blink the scan LED upon receipt of an EAS deactivate acknowledge signal. * No Blink LED on Deactivation ³ 1 4 6 1 0 3 Do not blink the sca...
Page 84 - Sensormatic ScanMax Pro; be connected to one of the RS232 scanner ports.
78 Sensormatic ScanMax Pro The following codes do not require that the MS2xx0 to be in scale program mode. The RS232 EAS cable must be connected to one of the RS232 scanner ports. EAS Function #3 ³ 9 9 8 0 6 7 For Sensormatic ScanMax Pro, get EAS’s hardware version, software version, and serial numb...
Page 87 - Display Software Numbers; The following code; does not; Display Software Number
81 Scanner Test Bar Codes Supplemental Tests Display Software Numbers The following code does not require that the MS2xx0 to be in scale program mode. This code is for test purposes only. The following code will display software numbers on the 2-digit diagnostic display. The lasers will be turned of...
Page 89 - Technical Assistance; Online Technical Assistance
83 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 E-mail: [email protected] Latin America Telephone: (803) 835-8000 T...
Page 90 - Product Service and Repair; Online Product Service and Repair Assistance
84 Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning ...
Page 92 - Honeywell Scanning & Mobility
Honeywell Scanning & Mobility 9680 Old Bailes Road For Mill, SC 29707 www.honeywellaidc.com 00-02034 Rev G 5/11