Page 2 - for your purchase of this product.; TABLE OF CONTENTS
1 PRO PLUS ® STRETCHER SCALE MODEL 2000KL Thank you for your purchase of this product. Please read this manual carefully and keep it handy for ready reference. TABLE OF CONTENTS CAUTION AND WARNING.................................................................................................... 2 ...
Page 3 - CAUTION AND WARNING; No scale should be used for
2 CAUTION AND WARNING To prevent injury and damage to your scale, please follow these instructions very carefully. • To ensure proper operation of the ProPlus® Stretcher Scale, this operation manual should be reviewed carefully before operation. Keep this manual available for future reference, and a...
Page 4 - SPECIFICATIONS; GENERAL; Health o meter’s ProPlus; SCALE SPECIFICATIONS; Capacity and Resolution; Adapter 120VAC - 6VDC - 60Hz or 6 x D size batteries; Environmental
3 SPECIFICATIONS GENERAL Health o meter’s ProPlus ® Stretcher Scale Model 2000KL uses highly sophisticated microprocessor technology. This scale is designed to provide accurate, reliable and repeatable weight measurements and features that make the weighing process simple, fast and convenient. The s...
Page 5 - ASSEMBLY INSTRUCTIONS; Lifter mast
4 ASSEMBLY INSTRUCTIONS Before Assembly The Model 2000KL ProPlus® Stretcher Scale is shipped disassembled in two (2) separate cartons. Carefully inspect all cartons for shipping damage before unpacking. If damage is found, contact your shipper or Healthometer Professional immediately. Claims must be...
Page 6 - Figure 2
5 ASSEMBLY INSTRUCTIONS Assembling the Patient Lifter 1. Place the Stretcher Storage Tray on the Lifter Base, as shown below, before attaching the Lifter Mast. Figure 2 2. Remove black plastic protective caps from Lifter Mast. Insert the bottom of the Lifter Mast and Hydraulic Pump assembly into the...
Page 8 - 0x2 1⁄2” hex screw and tighten the self lock nut on its other side.; Note
7 ASSEMBLY INSTRUCTIONS 4. Connect the Lifter Boom and the Display Support to the Lifter Mast using the NC ⅜ - 20x2 ½” hex screw and tighten the self lock nut on its other side. Note : This screw is the axis of the Lifter Boom, so it is imperative that the three parts – Lifter Boom, Lifter Mast and ...
Page 9 - Figure 4; : Do not attach the power cord at this point.
8 ASSEMBLY INSTRUCTIONS Figure 4 10. Position the Display Assembly close to the Display Support. Connect the load cell cable connector to the load cell port on the rear of the Display Assembly and insert and secure the cable into the center channel in the display. Note : Do not attach the power cord...
Page 10 - Figure 5
9 ASSEMBLY INSTRUCTIONS Figure 5 15. Hang the Load Cell Assembly on the two hooks at the end of the Lifter Boom, using the loops on top of the Load Cell Assembly. 16. Connect the end of the Load Cell Cable coming out of the center of the Load Cell Assembly to its port in the Lifter Boom. 17 Use the ...
Page 11 - SET UP; Preparing the Scale for Use; Replacing Batteries
10 SET UP Preparing the Scale for Use 1. Remove protective plastic film from keypad and display. 2. Place batteries in the battery holder (see “Replacing Batteries”). 3. Plug the scale’s AC adapter into the power source. 4. Press the ON/OFF button to turn the scale on. The display will show “Health ...
Page 12 - OPERATION INSTRUCTIONS
11 OPERATION INSTRUCTIONS Preweighing the Stretcher 1. Make sure the scale is free of load (nothing is hanging from it), including the stretcher. 2. Press the ON/OFF button to turn the scale on. 3. Wait until ”000 Lb 00 oz ” and “ZERO” on the left side of the display will appear. The scale will reme...
Page 13 - Release the hanging loops from the lifter.; ZERO key. Replace the stretcher after zeroing.
12 OPERATION INSTRUCTIONS 4. Release the hanging loops from the lifter. Note : The scale is programmed to save the last setting chosen as well as the weight of the stretcher as tare weight. This enables weighing a number of patients without having to re-set the scale. If a weight was added or reduce...
Page 14 - ITEM DESCRIPTION
13 OPERATION INSTRUCTIONS Figure 7. Keypad ITEM DESCRIPTION FUNCTION POWER Turns scale ON and OFF. ZERO Zeros the scale prior to weighing. HOLD/RELEASE Holds the value of the weighed object on the display until the button is pressed again to clear the value. Also used to scroll down in the menu. REW...
Page 15 - MENU; cd; 1 WEIGHT DISPLAY MODE; Figure 9. Weight Display Mode
14 OPERATION INSTRUCTIONS MENU In the menu screen the user can set preferences and/or instruct the scale how to handle stored data. The menu can be navigated using the up and down keys ( cd ) or by entering the associated menu position number with the keypad. The menu has a “roll-over” way of workin...
Page 16 - WEIGHT; Important; and the; Automatic Tare; MANAGEMENT
15 OPERATION INSTRUCTIONS 02 TARE WEIGHT NOTE: Due to the scale’s sensitivity, we recommend using the REWEIGH function prior to setting the TARE weight, in order to eliminate any operator interference with the item to be tared out. There are two ways to manually enter a tare weight (such as the weig...
Page 17 - Download
16 OPERATION INSTRUCTIONS 3. The scale will prompt you to enter the patient’s height. Use the keypad to enter the height in 1/4" (1=1/4, 2=1/2, 3=3/4) or 1 cm increments (use inches for weight in lb, cm for kg). Press ENTER. 4. Display will read the patient’s BMI. The scale offers you two option...
Page 18 - now; SETTINGS; Auto Hold Time
17 OPERATION INSTRUCTIONS 04 Transfer now All the values stored in memory are transferred to the PC and the scale memory is cleared of all values. If the transfer was unsuccessful, the values are kept in memory until successfully transferred or cleared. 05 Clear memory All the values stored in memor...
Page 19 - Auto Off Time
18 OPERATION INSTRUCTIONS 03 Auto Off Time The user can determine how long the scale will operate before turning off automatically due to inactivity. Default time is 10 minutes. If the value is set to zero, the auto off function is disabled. 04 Tone Volume There is an option to adjust the beeping to...
Page 21 - TEST
20 OPERATION INSTRUCTIONS Set the date using the up and down keys cd and enter the values on the keypad. 02 About This screen displays the software version of the scale. 06 SYSTEM TEST 01 Battery Test The scale will display the estimated amount of battery life remaining until the batteries will have...
Page 22 - Test; Retain Entered Values
21 OPERATION INSTRUCTIONS 03 UI Test The scale has a diagnostic routine where it tests the User Interface (UI) hardware functionality (LCD, keypad). In order to do this the user has to press all the keys according to the messages displayed on the screen. If the requested command was not received or ...
Page 23 - Prompt For Height
22 OPERATION INSTRUCTIONS 02 Disp Height & ID When the user selects to display the height and ID of the user, it will be displayed at the bottom of the screen. We recommend the use of this function to ensure that the patient’s correct ID and height have been entered. 03 Prompt For Height When th...
Page 24 - Stretcher Scale Model 2000KL. Maintenance operations other; MAINTENANCE; Disconnect the scale from the AC power source.; Do not immerse the scale into cleaning or other liquid solution.
23 MAINTENANCE GENERAL This section provides instructions for maintenance, cleaning, troubleshooting and operator replaceable parts for the ProPlus ® Stretcher Scale Model 2000KL. Maintenance operations other than those described in this section should be performed by qualified service personnel. MA...
Page 25 - TROUBLESHOOTING; SYMPTOM
24 TROUBLESHOOTING Refer to the following instructions to check and correct any failure before contacting service personnel. SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Scale does not turn on 1. Dead Battery 2. Faulty electrical outlet 3. Bad power supply 1. Replace batteries 2. Use a different outlet ...
Page 26 - CALIBRATION PATH; Operator Action; EXPLODED VIEW OF SCALE
25 CALIBRATION PATH The calibration is performed in Kg or Lb, according to the units of measure used upon entering into the calibration path. Operator Action Display 1. Press ON/OFF button and immediately press and hold HOLD/RELEASE button for 3-4 seconds Calibration Process 2. Press ENTER Enter loa...
Page 28 - PARTS LIST
27 PARTS LIST Key No. Part No. Description Qty. 1 1109403-0 DISPLAY ASSEMBLY 1 2 2268101-0 TILT MECH. ASSEMBLY 1 3 3848401-0 PLASTIC WASHER 2 4 401369 PLASTIC OVAL BAR COVER 3 5 HEX. HEAD SCREW NC 3/8-16*2 1/2 1 6 HEX. HEAD SCREW NC 3/8-16*1 3/4 1 7 2268001-0 LIFTER BOOM ASSEMBLY 1 8 2034701-0 MAIN ...
Page 29 - WARRANTY; LIMITED WARRANTY; What does the Warranty Cover?; Patents Pending
28 WARRANTY LIMITED WARRANTY What does the Warranty Cover? Pelstar LLC scales are warranted from date of purchase against defects of materials or in workmanship for a period of three (3) years. If product fails to function properly, return the product, freight prepaid and properly packed to Pelstar....
