Hayter 533A - Manual

LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free from defectsin material and workmanship under normal use and service for a period of three years from thedate of purchase. The manufacturer of the engines furnish their own warranty and services are ...

SAFETY PRECAUTIONS This safety alert symbol indicates important safety messages. Whenyou see this symbol be alert to the possibility of injury. Carefully readthe following and inform others. Your mower is perfectly safe if used correctly. Failure to observe thefollowing precautions may result in ser...

SAFETY PRECAUTIONS Do not tilt the mower when starting the engine. Do not put hands or feet near or under rotating parts. Never pick up or carry the mower while the engine is running. Never lift/open the rear deflector/door while the engine is running. Never touch the exhaust/exhaust guard or coolin...

Allow the engine to cool before storing in any enclosure. To reduce thefire hazard, keep the engine and the surrounding deck area free ofgrass, leaves, or excessive grease. Check the rear deflector and grassbag frequently for wear or deterioration.Replace worn or damaged parts for safety. If the fue...

Remove the mower from the packaging and check that the followingitems have been supplied correctly. If any items are missing contact,your local Hayter dealer. 1. Engine Handbook. 4. Mulcher Plug Note.(Inside Chute) 2. Warranty Reg. Card. 5. Side Discharge Chute 3. Grassbag. To prevent accidents cut ...

To prevent engine damage the engine is shipped without oil orpetrol. The engine must be filled with the correct grade of oil andpetrol before starting the engine. Always use high quality detergent oil classified SAE 30 Oil. Never useadditives with this oil.To prolong the life of your engine it is im...

Operate all control levers several times and ensure that the cablesmove freely. Check that the engine stop and ground drive clutch leversreturn freely to their rest position when released. Move the throttle control lever to the ‘Fast’ position. Push the primer button 5 times allowing 2 seconds betwe...

Hold the handlebar and operate the ground drive clutch lever topower the mower in a forward direction. When the ground drive clutch lever is disengaged the mower may bepushed. This feature is useful when mowing in confined areas. The mower has a three speed rear wheel transmission system. Tochange t...

OPERATING Remove the rear discharge chute by removing nuts and washers.Slide the assembly from under the the shoulder bolt (A). Slide the new side dicharge chute assembly under the shoulder bolt(A). Then fasten the front and the back of the assembly with the fas-teners. To prevent engine overloading...

There is very little work to do this month apart from brushing awayleaves. Keep off the grass if frozen or waterlogged. Rake the grass thoroughly. Spike the lawn to aerate and stimulate soilorganisms and root growth and apply lawn sand if necessary. The yearly lawn work programme really starts this ...

Keep mowing regularly and watering as necessary. Fill any crackscaused by drought with a mixture of sharp sand and soil. In dry weath-er conditions leave the grass longer to help retain ground moisture. Raise the height of cut to allow the grass to thicken and protect theroots from the winter frost ...

Double 3 Check the oil level daily before starting the engine and ensure that thecorrect oil level is maintained. Refer to-‘Before Starting the Mower’for oil checking and filling instructions. Change the engine oil after the first 5 hours of operation and thereafteraccording to the ‘Maintenance Sche...

Use only Briggs & Stratton spark tester (1) to check for a spark asshown in the diagram. Replace the spark plug every 100 hours or every season, whicheveroccurs first. A spark plug wrench is available from any authorisedBriggs & Stratton service dealer. Check the spark plug gap with a feeler...

Lubricate the wheels, pivot points and linkages with engine oil every 25operating hours. Apply a good quality medium grease to the inner control cables at thepoint of entry and exit from their outer casing. Drain the fuel by running the engine until the fuel tank is empty and theengine stops. Remove...

Assemble the cutterblade (1) with the turned up edges facing towardsthe engine. Secure the cutterblade using the belleville washers (2)washer (3) and new fixing bolt (4) and tighten to a torque of 47.5Nm. To prevent accidents never reuse the fixing bolt. A slightly worn cutterblade may be re-sharpen...

Double 3 Storage To store the handlebar unscrew the 2 small securing knobs sufficient-ly to allow it to pivot forwards to rest against the mower. Take care toensure that the control cables do not become snagged at the pivot pointand depress the engine stop lever to prevent it being damaged throughco...

TROUBLE SHOOTING PROBLEM POSSIBLE FAULT REMEDY Engine will not turn over Incorrect oil level. Check oil level. Obstruction under deck. Remove obstruction. Engine smokes Excess oil level. Check oil level. Air cleaner cartridge oil Service air cleaner. soaked or blocked. Engine runs then stops Fuel st...

DECLARATION OF CONFORMITY 1.27 VIBRATION INFORMATION Lawnmower vibration information. RMS acceleration measured in 3 - axes at operators contact position on the handlebars. CODE 533A = 4.87 ms -2 EC DECLARATION OF CONFORMITY HAYTER LIMITED, Spellbrook, Bishop’s Stortford, Herts CM23 4BU ENGLAND decl...

NO. DESCRIPTION PART NO. QTY ITEM NOTE 48 Hub Cap MU43615 2 49 Support, Wheel MU71370E701 1 50 Nut 09203 1 51 Nut MU15x88 2 52 Rear Discharge Chute MU671289 1 53 Deflector, Rear MU671296 1 54 Rod MU71319 Z 1 55 Cap, Push On MU710285 4 56 Key, Woodruff #6 1662 1 57 Plate, Bagger MU671298 1 58 Door, R...

1.32 Mower Serial No:................................................................................. Engine Model:.................................. Type:....................................... Code:..................................... Notes: CUSTOMER INFORMATION /NOTES