Harbor Breeze 40843 - User Manual

H

arb or Bree z

e

H

a rb or Br eez

e

Black (hot/power)

White (neutral)

Red

Whit

e

White

White

Black

Blue

Blue

Black

Antenna

ASSEMBLY INSTRUCTIONS

OPERATING INSTRUCTIONS

SAFETY INFORMATION

1. Use existing pull chains on the desired

fan to set fan speed to high and to turn

the light on.

2. Turn off circuit breakers and wall

switch to the fan.

DANGER:

Failure to disconnect

power supply prior to installation may

result in serious injury or death.

3. Lower the canopy of the previously

assembled fan and insert receiver (E).

Note:

If installing this product with

a new fan, insert the receiver (E) in

the mounting bracket before wiring

the fan; wire the fan according to

these instructions, then continue fan

assembly as directed in the fan’s

instruction manual.

• Connect the Red wire with red label from the receiver to the Black (hot/

power) supply wire.

• Connect the White wire with red label from the receiver to the White

(neutral) supply wire.

CEILING FAN REMOTE

CONTROL

ITEM #0745358

MODEL #40843

Serial Number

Purchase Date

ATTACH YOUR RECEIPT HERE

Harbor Breeze

®

is a registered trademark

of LF, LLC. All rights reserved.

EB15502

9130 • 102815

Read instructions completely before installing remote control.

WARNING:

If the color of the household supply wires is different than what is referred to in the instructions below, a professional electrician should determine

proper wiring.

CAUTION:

•

Do not install in damp locations. For indoor use only.

•

Do not use with fans that have integrated remote controls.

•

Be sure the outlet box is properly grounded or that a green or bare (ground) wire is present.

•

This unit is intended to control a ceiling fan with electrical source of AC 110/120V, 60Hz.

•

To reduce the risk of fire or electric shock, do NOT use a full-range dimmer switch to control the fan speed.

•

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Printed in

China

3

4

1

2

5

9

1

4. Disconnect existing wire connections,

then secure all wire connections with

wire connectors (F) and push-on

connectors (D) according to diagram

and these steps:

• Connect the Blue wire with white

label from the receiver to the Blue

fan wire.

• Connect the Black wire with white

label from the receiver to the Black

fan wire.

• Connect the White wire with white label

from the receiver to the White fan wire.

Fan Pull

Chain

Light Pull

Chain

Light

Fan

Learn

Canopy

1. To operate the fan using the remote (A), press and release the following buttons:

Fan -

Turns fan on and off.

Note:

Use fan pull chain to adjust fan speed as desired.

Light -

Turns light on and off.

Learn

- Syncs remote control to receiver. The remote was synced at the factory. Should it become necessary to

re-sync the remote, turn off the main power, then turn it back on. Within 30 seconds, use a small screwdriver to press

and hold the learn button on the remote for 3 seconds. The fan will turn on and light (if applicable) will blink three

times, signaling a successful synchronization.

Questions?

Call our customer service department

at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday -

Thursday, 8 a.m. - 5 p.m., EST, Friday.

Remote

Qty. 1

Wall Bracket

Qty. 1

Battery

Qty. 2

Receiver

Qty. 1

Wire Connector

Qty. 3

Push-on

Connector

Qty. 3

Mounting Screw

Qty. 2

5. Wrap electrical tape (not included)

around each wire connector (F)

down to the wire. Then, push wire

connections into the outlet box.

Place the Green and White wire

connections on the opposite side of

the outlet box from the Black and

Blue wire connections.

6. Reinstall the canopy.

7. Turn on power supply and wall

switch to the fan and wall control.

8. Remove the battery cover from the

back of the remote (A) and install

the two AAA batteries (C). Replace

the battery cover and press the fan

power button to ensure the LED

indicator illuminates and the fan

turns on.

9. If desired, the wall bracket (B) can

be attached to a wall using the

mounting screws (G). Slide small

plate over mounting screws (G),

then rest the remote (A) in the wall

bracket (B) for easy storage.

8

7

Small

Plate

Battery

Compartment

Fan

Power

Light

Power

LED Indicator

A

B

C

E

D

F

G

E

F

C

B

G

A

6

D