Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................... 2 Contact Info.................................................... 2Manual Accuracy ........................................... 2Identification ................................................... 3 SECTION 1: SAFETY ........
Page 4 - INTRODUCTION; Manual Accuracy; Contact Info
-2- Model T26417/T26418 (Mfd. Since 11/13) INTRODUCTION We are proud to provide a high-quality owner’s manual with your new machine! We made every effort to be exact with the instruc-tions, specifications, drawings, and photographs contained inside. Sometimes we make mistakes, but our policy of cont...
Page 5 - Identification
Model T26417/T26418 (Mfd. Since 11/13) -3- Figure 1. Identification. Identification To reduce your risk of serious injury, read this entire manual BEFORE using machine. Spindle Spindle Hex Nut Drum and Sanding Sleeve ON/OFF Paddle Switch with Disabling Key Table Table Inserts Table Tilt Control Tabl...
Page 6 - MODEL T26417 BENCHTOP OSCILLATING SANDER
-4- Model T26417/T26418 (Mfd. Since 11/13) The information contained herein is deemed accurate as of 4/10/2014 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model T26...
Page 8 - MODEL T26418 FLOOR-MODEL OSCILLATING SANDER
-6- Model T26417/T26418 (Mfd. Since 11/13) The information contained herein is deemed accurate as of 4/10/2014 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model T26...
Page 10 - For Your Own Safety, Read Instruction; NOTICE; Safety Instructions for Machinery
-8- Model T26417/T26418 (Mfd. Since 11/13) ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and a...
Page 12 - Additional Safety for Spindle Sanders
-10- Model T26417/T26418 (Mfd. Since 11/13) FEED RATE. Never jam a workpiece against the sanding surface. This can cause the workpiece to kick back or damage the machine. Firmly hold the workpiece and ease it against the spindle using light pressure. Allow the machine to do the work—do not force the...
Page 13 - SECTION 2: POWER SUPPLY; Availability
Model T26417/T26418 (Mfd. Since 11/13) -11- SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To m...
Page 15 - Unpacking; Needed for Setup
Model T26417/T26418 (Mfd. Since 11/13) -13- SECTION 3: SETUP Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover any damage, please call us immediately at (570) 546-9663 for advice. Save the containers a...
Page 16 - Inventory
-14- Model T26417/T26418 (Mfd. Since 11/13) NOTICE If you cannot find an item on this list, care- fully check around /inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory. Inventory The following is ...
Page 17 - Workbench Load; Placement Location
Model T26417/T26418 (Mfd. Since 11/13) -15- Cleanup Site Considerations Figure 5. T26417 Minimum working clearances. The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well,...
Page 18 - Floor; Anchoring to Concrete Floors; Bench
-16- Model T26417/T26418 (Mfd. Since 11/13) Anchoring machinery to the floor prevents tipping or shifting and reduces vibration that may occur during operation, resulting in a machine that runs slightly quieter and feels more solid. If the machine will be installed in a commercial or workplace setti...
Page 20 - Test Run
-18- Model T26417/T26418 (Mfd. Since 11/13) Figure 12. Removing switch key from paddle switch. Test Run 5. Try to start machine by pressing switch but- ton. Machine should NOT start. If it does start, the switch disabling feature is not functioning properly and the switch must be replaced. Once asse...
Page 21 - SECTION 4: OPERATIONS; Operation Overview
Model T26417/T26418 (Mfd. Since 11/13) -19- SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the nov-ice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are e...
Page 22 - Installing Sanding; Installing Sanding Drums
-20- Model T26417/T26418 (Mfd. Since 11/13) Installing Sanding Drum/Sleeve 1. DISCONNECT MACHINE FROM POWER. 2. Thread the assembled sanding spindle, drum, and sleeve into the machine spindle. 3. Insert 22mm and 17mm wrenches through access panel beneath table (see Figure 13) and onto machine spindl...
Page 23 - Changing Spindle Sanding Sleeve
Model T26417/T26418 (Mfd. Since 11/13) -21- 4. Pull sanding drum and sleeve off of sanding spindle. 5. Pull sanding sleeve off of sanding drum. 6. Re-assemble new sanding sleeve and sand- ing drum. Note: Sanding sleeve slides over sanding drum easier if done prior to placing drum over spindle. 7. Re...
Page 24 - Tilting Table
-22- Model T26417/T26418 (Mfd. Since 11/13) Tilting Table To tilt the table: 1. Loosen locking lever shown in Figure 15 by rotating counterclockwise. Figure 15. Loosening table tilt lock lever. 2. Loosen locking ring that holds table tilt by rotating it counterclockwise (see Figure 16). 3. Set table...
Page 26 - SECTION 5: ACCESSORIES
-24- Model T26417/T26418 (Mfd. Since 11/13) SECTION 5: ACCESSORIES ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE Ref...
Page 28 - SECTION 6: MAINTENANCE; Lubrication
-26- Model T26417/T26418 (Mfd. Since 11/13) SECTION 6: MAINTENANCE Cleaning Model T26417/T26418 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Treat all unpainted cast...
Page 29 - Troubleshooting
Model T26417/T26418 (Mfd. Since 11/13) -27- Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and ma...
Page 30 - Wiring Safety Instructions
-28- Model T26417/T26418 (Mfd. Since 11/13) SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine...
Page 41 - WARRANTY CARD
C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...
