Grizzly Industrial T23092 - Manual

Page 2 - safety instructions for spray guns; safety; for your own safety read instruction manual; NOTICE

Model t23092 high-pressure spray gun -1 - safety instructions for spray guns 1. read this manual. this gun may cause personal injury if used incor-rectly. this manual contains proper safety and operating instructions that must be followed to reduce this risk. 2. Wear eye protection. Material sprayed...

Page 4 - section 2: introduction; foreword

Model t23092 high-pressure spray gun -3 - section 2: introduction the specifications, details, and photographs in this manual represent the Model h8222 as supplied when the manual was prepared. however, owing to grizzly’s policy of continuous improvement, changes may be made at any time with no obli...

Page 5 - inventory

Model t23092 high-pressure spray gun -4 - your spray gun was carefully packaged for safe transportation. remove the packaging materials from around the tool and inspect it. if you discover the spray gun is dam-aged, please immediately call Customer Service at (570) 546-9663 for advice. save the cont...

Page 6 - identification & controls

Model t23092 high-pressure spray gun -5 - identification & controls refer to figure 3 and the following descriptions to gain an understanding of the features and controls of this spray gun. Be sure to read the entire manual before beginning spraying operation to ensure a safe and efficient exper...

Page 7 - section 4: operations; spraying

Model t23092 high-pressure spray gun -6 - section 4: operations eXplosion hazard ! do not smoke or have any source of flame or spark near spraying. vapors will explode if ignited. toXic fumes ! always use an approved spray booth or well ven-tilated area when spraying. never spray in a confined space...

Page 9 - atomizing cap; pattern control

Model t23092 high-pressure spray gun -8 - 14. Maintain an even speed when spraying and overlap each stroke by 50%. this will ensure even coverage, as shown in on the left of figure 5. overlapping less than 50%, as shown on the right, may lead to missed spots or streaky results. 6"12" Correct...

Page 10 - section 5: accessories

Model t23092 high-pressure spray gun -9 - section 5: accessories figure 9. g6261 Campbell hausfeld™ water filter. g6261— campbell hausfeld™ Water filterremove damaging water vapor before it reaches your spray gun. this highly effective, five micron filter features a see- through bowl and easy in-lin...

Page 11 - section 6: maintenance; cleaning

Model t23092 high-pressure spray gun -10 - section 6: maintenance to reduce the risk of injuries from compressed air explosion, always disconnect the air line before per-forming maintenance or service. cleaning properly cleaning the spray gun helps to ensure good spraying results and long gun life. ...

Page 12 - lubrication

Model t23092 high-pressure spray gun -11 - 5. rinse these parts thoroughly in solvent, then dry with compressed air or let air dry. note: If the small holes in the atom- izing cap become blocked, soak the cap in clean solvent. If the blockage still exists, clear the blockage with a small needle, tak...

Page 13 - troubleshooting; symptom

Model t23092 high-pressure spray gun -12 - troubleshooting symptom possible cause solution Fluttering or spit-ting spray. 1. dry or worn fluid nozzle seat permits air to seep into fluid passage. 2. Material level too low.3. Fluid nozzle obstructed.4. dry needle packing. 1. tighten fluid tip or repla...

Page 16 - Warranty

Warranty Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. Thi...

Grizzly Industrial T23092 - Manual

Table of Contents:

Summary

Other Grizzly Industrial Models