Grizzly Industrial T21888 - Manual

model t21888 (mfg. since 2/10) - 6 - section 1: circuit reQuirements serious personal injury could occur if you connect the machine to the power source before you have com-pleted the set up process. do not connect the machine to the power source until instructed to do so. 110v operation amperage dra...

model t21888 (mfg. since 2/10) - 8 - unpacking section 2: set up your air compressor left our warehouse carefully packed. if you discover the air compressor is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. save the container and pa...

model t21888 (mfg. since 2/10) - 9 - test run & break in to test run and break in the air com-pressor: 1. put on safety goggles, and place the compressor on a solid, level surface. 2. make sure the on/off lever is in the up or the OFF position, as shown in figure 4. 6. observe the tank pressure ...

model t21888 (mfg. since 2/10) - 10 - section 3: operations read the manual before operation. become familiar with this tool, its safety instructions, and its operation before beginning any work. serious personal injury may result if safety or operational information is not under-stood or followed. ...

model t21888 (mfg. since 2/10) - 11 - operation Before connecting an air tool to this air compressor, have a general idea as to what the CFm (Cubic Feet per minute) air requirement is for your tool. if the tool has a CFm requirement higher than what the compressor can supply, the tool will oper-ate ...

model t21888 (mfg. since 2/10) - 12 - figure 13. h7274 Campbell hausfeld™ pressure regulator. h7274 — campbell hausfeld™ pressure regulatorsince psi drops through lengths of air hose, attaching a regulator directly to the spray gun ensures accurate air regulation for the best results possible. provi...

model t21888 (mfg. since 2/10) - 13 - section 4: maintenance schedule daily daily before use, perform the following checks: 1. look at the sight glass on the crank- case and make sure it is filled with oil to the correct level. 2. Check for worn or damaged electri- cal cords and plugs. inspect air h...

model t21888 (mfg. since 2/10) - 14 - Quarterly after every approximately 300 run-time hours, or 3 months, perform the follow-ing maintenance: 1. Change the oil in the air compressor pump as described in changing oil on page 18. 2. Check for air leaks and correct as needed. 3. pull and release the m...

model t21888 (mfg. since 2/10) - 15 - section 5: service this section is provided for your convenience—it is not a substitute for the grizzly service department. if you need help troubleshooting, replacing parts, or you are unsure of how to perform the procedures in this section, then feel free to c...

model t21888 (mfg. since 2/10) - 19 - fixing air leaks to find air leaks: 1. Allow the compressor to build air pres- sure to the rated pressure. 2. disConnECt thE ComprEssor From poWEr. 3. listen for the sound of air to find fittings that may be leaking. 4. spray the suspected air leak with a soap a...

model t21888 (mfg. since 2/10) - 20 - the pressure switch ensures the compres-sor will turn ON (cut-in) when the tank pressure drops to approximately to 85 psi. the compressor will shut OFF (cut-out) when the air tank reaches maximum of 115 psi. should the cut-out switch fail, the pressure relief va...

model t21888 (mfg. since 2/10) - 21 - When storing your air compressor, fol-low these guidelines: 1. push the compressor on/oFF lever down to the oFF position. 2. disconnect the compressor from power. 3. Unplug the compressor. 4. run the air tool to relieve the air pres- sure in the hose, then remov...

model t21888 (mfg. since 2/10) - 22 - 8 7 6 12 17 16 46 3 4 2 1 40 39 37 35 9 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 38 41 42 54 53 5 51 52 55 79 73 71 70 72 74 76 7778 83 84 56 58 59 60 61 63 64 65 66 67 68 80 81 69 62 63 82 10 11 86 87 86 87 43 45 44 88 89 parts breakdown

model t21888 (mfg. since 2/10) - 23 - parts list REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT21888001 CRANKCASE 42 PW02M FLAT WASHER 5MM 2 PT21888002 CRANKSHAFT 43 PT21888043 MOTOR 110V 3 PT21888003 CONNECTING ROD 44 PT21888044 HOT PIPE WARNING LABEL 4 PT21888004 CONNECTING ROD BOLT 45 PT21888...

Warranty grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-nance. th...

Warranty card name _________________________________________________________________street _________________________________________________________________City _______________________ state _________________________ zip _________phone # ____________________ Email ________________________ invoice # ...

fold along dotted line grizzly industrial, inc.p.o. box 2069bellingham, Wa 98227-2069 tape along edges--please do not staple name________________________________ street________________________________ city______________state______zip_______ send a grizzly catalog to a friend: place stamp here