Grizzly Industrial T10828 - Manual

Page 3 - NOTICE; Safety Instructions for Power Tools

Model T10828 (Mfd. since 12/14) -1 - SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended t...

Page 6 - SECTION 2: INTRODUCTION; Foreword

Model T10828 (Mfd. since 12/14) -4 - SECTION 2: INTRODUCTION We are proud to offer this manual with your new T10828 Rotary Tool! We've made every effort to be exact with the instruc-tions, specifications, drawings, and photo-graphs of the T10828 Rotary Tool we used when writing this manual. However,...

Page 7 - Identification

Model T10828 (Mfd. since 12/14) -5 - Identification A. Flexible Shaft Collet NutB. Flexible Locking SleeveC. Inner SpindleD. Flexible Shaft Locking RingE. Flexible ShaftF. Spindle Lock ButtonG. Motor Brush CapH. Variable-Speed ControlI. Tool HangerJ. ON/OFF SwitchK. Motor Brush Cap L. Rotary Tool Lo...

Page 9 - Power Connection; Test Run

Model T10828 (Mfd. since 12/14) -7 - Connecting Power Power Connection After you have completed all previous setup instructions, the machine is ready to be connected to the power supply. To avoid unexpected startups or property damage, use the following steps whenever connecting or disconnecting the...

Page 10 - SECTION 4: OPERATIONS; Installing Bits

Model T10828 (Mfd. since 12/14) -8 - SECTION 4: OPERATIONS Failure to wear safety glasses while operating the grinder could cause serious personal eye injury. The Model T10828 uses bits and cutters with a 1 ⁄ 8 " diameter shaft. See the Grizzly catalog or website for a complete listing of availa...

Page 11 - Installing Flex Shaft

Model T10828 (Mfd. since 12/14) -9 - Use low RPM settings when work- ing with plastics or other materials with low melting points. Melted plastics can liquefy, be thrown into the air, and stick to the operator, causing serious personal injury. Installing Flex Shaft The flex shaft allows the user to ...

Page 12 - SECTION 6: MAINTENANCE; Schedule; Carbon Brush Replacement

Model T10828 (Mfd. since 12/14) -10 - SECTION 6: MAINTENANCE ! Always DISCONNECT POWER before servicing, adjusting, or doing maintenance to reduce the risk of accidental injury or electrocution. Schedule For optimum performance from your machine, follow this maintenance sched-ule and refer to any sp...

Page 13 - Troubleshooting; Symptom

Model T10828 (Mfd. since 12/14) -11 - Troubleshooting Symptom Possible Cause Solution Motor won't start. 1. Brushes dirty or worn.2. Power supply inoperative.3. Power cord defective. 1. Clean or replace burshes.2. Check circuit breaker.3. Replace power cord. Bit slipping. 1. Collet not tight. 2. Col...

Page 14 - Parts Breakdown

Model T10828 (Mfd. since 12/14) -12 - Parts Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT10828001 POWER CORD 18G 2W 71" 1-15P 10 PT10828010 STATOR 2 PT10828002 TOOL HANGER 11 PT10828011 ROTOR 3 PT10828003 ON/OFF SWITCH, CANAL MR-2 125V 12 PT10828012 HOUSING (R) 4 PT10828004 AIR DE...

Page 15 - WARRANTY

Model T10828 (Mfd. since 12/14) -13 - WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or a...

Grizzly Industrial T10828 - Manual

Table of Contents:

Summary

Other Grizzly Industrial Models