Grizzly Industrial T10808 - Manual
Grizzly Industrial T10808 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Safety for Wood Lathes
- Page 3 – Safety for Chucks
- Page 8 – Bottom Jaw Removal & Installation
- Page 9 – Maintenance
- Page 10 – Parts
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]
MODEL T10808
WOOD LATHE CHUCK SET
INSTRUCTIONS
COPYRIGHT © DECEMBER, 2013 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TS16132 PRINTED IN CHINA
Introduction
The T10808 2
3
⁄
4
" Wood Lathe Chuck Set includes
a scroll chuck with four self-centering bottom jaws
and five top jaw sets to provide a variety of grip-
ping needs for your wood turning projects.
Specifications
Chuck Body Diameter ................................... 2
3
⁄
4
"
Chuck Bore ...........................................1" x 8 TPI
Outside Grip Range:
— #1 Step Jaws ..............................
3
⁄
32
" –
5
⁄
8
"
— #2 Round Jaws ......................... 1
1
⁄
8
"–1
3
⁄
4
"
— #3 Round Jaws ......................... 2
1
⁄
4
"–2
3
⁄
8
"
— Pin Jaws .........................................
1
⁄
4
" –
7
⁄
8
"
Inside Grip Range:
— #1 Step Jaws (Upper Step) ..........
3
⁄
4
"–1
1
⁄
4
"
— #1 Step Jaws (Lower Step) ....... 1
1
⁄
2
"–2
1
⁄
8
"
— #2 Round Jaws ......................... 1
1
⁄
2
"–2
1
⁄
8
"
— #3 Round Jaws ......................... 2
7
⁄
8
"–3
3
⁄
8
"
— Pin Jaws ....................................
15
⁄
16
"–1
1
⁄
2
"
Flat Jaws Maximum Outside Diameter ........ 4
3
⁄
8
"
Flat Jaws Minimum Inside Diameter ............2
1
⁄
16
"
Woodworm Screw Required Hole ...........
1
⁄
4
" x
7
⁄
8
"
A
B
C
D
E
G
F
I
H
J
K
L
M
N
Inventory
Description: Qty
A. T-Handle Hex Wrench 3mm ....................... 1
B. Spindle Lever 8mm .................................... 1
C. Woodworm Screw ...................................... 1
D. Lathe Chuck Key 8mm ............................... 1
E. Chuck Body ................................................ 1
F. Pin Jaws ..................................................... 4
G. #2 Round Jaws ........................................... 4
H. Grip Studs 18mm, M6-1 x 6 ....................... 8
I. Flat Jaws .................................................... 4
J. #1 Step Jaws .............................................. 4
K. Grip Studs 13mm, M6-1 x 6 ....................... 8
L. Cap Screws M4-.7 x 8 ................................ 8
M. #3 Round Jaws ........................................... 4
N. Hex Wrench 4mm ....................................... 1
To prevent personal injury, always under-
stand and follow all safety instructions in
your wood lathe owner's manual.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- Model T10808 Wood Lathe Chuck Set INTEGRITY OF STOCK. Verify each workpiece is free of knots, splits, nails, or foreign material to ensure it can safely rotate on spindle without breaking apart or causing turning tool kickback. WORKPIECE PREPARATION. Before mounting, cut off waste portions with ...
Model T10808 Wood Lathe Chuck Set -3- Safety for Chucks ENTANGLEMENT. Entanglement with a rotat-ing chuck can lead to death, amputation, broken bones, or other serious injury. Never attempt to slow or stop the lathe chuck by hand, and always roll up long sleeves, tie back long hair, and remove any j...
-8- Model T10808 Wood Lathe Chuck Set Woodworm ScrewThe woodworm screw is typically used with the #2 round jaw set for holding small items. Refer to the illustration below for closing the round jaws around the base of the screw. Woodworm Screw The woodworm screw has a very coarse 45° thread that pro...
