Grizzly Industrial H8236 - Manual

Page 3 - SAFETY; NOTICE

Model H8236 2-Piece Brad Nailer/Stapler Kit -1 - Safety Instructions for Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WO...

Page 4 - Safety Instructions for Pneumatic Tools

Model H8236 2-Piece Brad Nailer/Stapler Kit -2 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry whic...

Page 7 - INTRODUCTION; Foreword

Model H8236 2-Piece Brad Nailer/Stapler Kit -5 - INTRODUCTION Foreword Tool Data Brad Nailer Nail Size ..................................... 18 GaugeNail Length ........................................ 5 ⁄ 8 "–2" Magazine Capacity ...................... 100 NailsAir Inlet Fitting ..............

Page 8 - SETUP; Inventory; Unpacking

Model H8236 2-Piece Brad Nailer/Stapler Kit -6 - SETUP Inventory After you open the nailer case, you should find the following. Model H8236 Inventory (Figure 1) Qty A. Tool Oil Bottle .................................... 1 B. Hex Wrench Set (3 and 4mm) ........... 1 C. Safety Goggles ..................

Page 9 - Compressed Air

Model H8236 2-Piece Brad Nailer/Stapler Kit -7 - The Model H8236 is designed to be oper-ated at the following air pressures using clean, dry, regulated, compressed air: Tool Operating Air Pressure Brad Nailer .............................. 60–100 PSIStapler ..................................... 60–1...

Page 11 - OPERATIONS; Loading

Model H8236 2-Piece Brad Nailer/Stapler Kit -9 - OPERATIONS Loading Brad Nailer Nail Size ..................................... 18 GaugeNail Length ........................................ 5 ⁄ 8 "–2" Magazine Capacity ...................... 100 Nails To load your brad nailer: 1. DISCONNECT N...

Page 12 - Operating

Model H8236 2-Piece Brad Nailer/Stapler Kit -10 - If you have not read the safety instruc-tions in this manual, do not operate the nailer/stapler. Before you operate your nailer/stapler, place five to six drops of the included oil into the quick connect fitting where the nailer/stapler connects to t...

Page 13 - Clearing Jammed

Model H8236 2-Piece Brad Nailer/Stapler Kit -11 - A jammed nail/staple must be cleared before using the tool again. Brad Nailer To clear a jammed nail from the dis-charge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Depress the magazine latch and pull the magazine cover back until it stops. 3....

Page 15 - CLEANING & LUBRICATION; Cleaning

Model H8236 2-Piece Brad Nailer/Stapler Kit -13 - CLEANING & LUBRICATION Cleaning Use non-flammable solvent to clean the nose assembly of the nailer/stapler. Always be sure that the tool is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body o...

Page 16 - Brad Nailer Breakdown

Model H8236 2-Piece Brad Nailer/Stapler Kit -14 - H8236 PARTS � � � � � � � � � �� Brad Nailer Breakdown

Page 17 - Brad Nailer Parts List

Model H8236 2-Piece Brad Nailer/Stapler Kit -15 - Brad Nailer Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8235101 SPECIAL BOLT 36 PH8235136 COMPRESSION SPRING 2 PH8235102 EXHAUST PORT 37 PH8235137 SAFETY NOSE 3 PH8235103 COMPRESSION SPRING 38 PH8235138 DRIVER GUIDE 4 PB42M HEX BOLT ...

Page 18 - Stapler Breakdown and Parts List

Model H8236 2-Piece Brad Nailer/Stapler Kit -16 - Stapler Breakdown and Parts List �� ...

Page 19 - TROUBLESHOOTING; Symptom

Model H8236 2-Piece Brad Nailer/Stapler Kit -17 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking. 1. Loose screws in housing.2...

Page 20 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-nance. This is Gri...

Grizzly Industrial H8236 - Manual

Table of Contents:

Summary

Other Grizzly Industrial Models