Grizzly Industrial H8175 - Manual
Grizzly Industrial H8175 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Air Supply
- Page 3 – Changing Nozzles; Temperature Adjustment; Fluid Output Adjustment; NOTICE
- Page 4 – H8175 Parts Breakdown and List
Specifications
Air Regulator Inlet Size ............................
1
⁄
4
" NPT
Operating Temperature ................... 284°F–428°F
Maximum Temperature ...............................446°F
Operating Air Pressure .............................. 90 PSI
Glue Stick Diameter .........................................
1
⁄
2
"
Cord Length .................................................... 2 ft.
Weight ...........................................................3 lbs
Operation
1.
Connect the glue gun to the air regulator and
connect the air regulator to the air supply.
2.
Plug the glue gun into a grounded outlet and
turn it
ON
with the power switch located at the
base of the glue gun.
3.
Allow the gun to heat up for approximately 3–5
minutes.
MODEL H8175
PROFESSIONAL
PNEUMATIC GLUE GUN
INSTRUCTION SHEET
Figure 1.
Model H8175.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service!
EYE/SKIN BURN HAZARD!
Wear safety glasses and
protective clothing when
using this tool!
DO NOT EXCEED 100 PSI!
Personal injury could
occur.
ELECTRICIT Y HAZARD !
Electrocution or fire could
result if this tool is not
properly grounded. Do not
remove the ground pin.
Gun
Case
Air
Regulator
Screwdriver
Extra Nozzles
4.
Insert a
1
⁄
2
" diameter glue stick into the back
of the gun.
5.
Once the gun has fully heated, slowly squeeze
the trigger until the melted material begins to
flow from the nozzle.
Note:
When hot, rest the gun with the tip fac-
ing down, as shown in
Figure 1
, to prevent
melted glue from escaping the chamber and
increasing the risk of fire or personal injury.
6.
After the gluing operation is complete, allow
the glue gun to fully cool before storing it.
Glue sticks may remain in the glue gun when
it is not in use and be re-melted when the
glue gun is used again.
Note:
Never pull the glue stick out through
the back of the gun or it may damage the
feed mechanism. Cut off the extra portion of
the glue and feed the remainder through the
glue gun.
COPyRIGHT © MAy, 2008 By GRIzzLy INDuSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROvAL OF GRIZZLY INDUSTRIAL, INC.
#JM10780 PRINTED IN TAIWAN
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Model H8175 Professional Pnuematic Glue Gun -2- Air Supply The glue gun MuST be regularly lubricated with 3-4 drops of air tool oil directly into the air fitting before each use, as shown in Figure 2 . Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator A...
Model H8175 Professional Pnuematic Glue Gun -3- Changing Nozzles The Model H8175 glue gun comes with three noz-zles for different gluing applications and output amounts. The all metal nozzle is for heavy duty and high output applications. The long tip of the silicon nozzle is ideal for bonding items...
Model H8175 Professional Pnuematic Glue Gun -4- H8175 Parts Breakdown and List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8175001 GUN BODY 21 PH8175021 CABLE TIE 2 PH8175002 SPACER 22 PH8175022 SCREW 3 PH8175003 TEMPERATURE CONTROL 23 PH8175023 WASHER 4 PH8175004 GRIZZLY NAME PLATE 24 PH81750...
