Grizzly Industrial H8125 - Manual

Page 3 - Table of Contents

Table of Contents SECTION 1: SAFETY .......................................................................................................2 Safety Instructions for Machinery ...............................................................................2Additional Safety Instructions for Mini Grind...

Page 6 - Additional Safety Instructions for Mini Grinder

Model H8125 9.6V Mini Grinder Kit -4 - No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this mini grinder and other machinery with caution and respect. Failure to do so could resu...

Page 8 - SECTION 2: INTRODUCTION; Foreword

Model H8125 9.6V Mini Grinder Kit -6 - SECTION 2: INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 E-Mail: [email protected] Most importantly, we st...

Page 9 - Unpacking

Model H8125 9.6V Mini Grinder Kit -7 - Your Model H8125 was carefully packed when it left our warehouse. If you discover the Model H8125 is damaged after you have signed for delivery, please call Customer Service immediately at (570) 546-9663 for advice. Save the containers and all packing materials...

Page 10 - Inventory

Model H8125 9.6V Mini Grinder Kit -8 - Inventory A. 9.6V Mini Grinder with Battery B. Battery Charger C. 9.6V NiCad Battery D. Accessory Kit• 4-Piece Sanding Drum Set• 2-Piece Buffing Wheel Set• 36-Piece Sanding Disc Set• Collets 1 ⁄ 8 ", 1 ⁄ 4 " • Square Stone Dresser E. Carrying Case F. Fl...

Page 11 - SECTION 4: OPERATIONS; Charging the Battery

Model H8125 9.6V Mini Grinder Kit -9 - SECTION 4: OPERATIONS Charging the Battery To prevent potential problems during ship-ment, batteries are usually shipped with little or no charge. You must charge your new batteries before initial use. Note: The time to fully charge a battery is approximately 3...

Page 12 - Installing Bits; Using the LED Light Attachment

Model H8125 9.6V Mini Grinder Kit -10 - DO NOT use bits or cutters with a cutting surface larger than 1". The bit could break apart under the stresses of high speed use causing serious personal injury. 4. Use the small switch on the underside of the light attachment to switch the LED's ON and OF...

Page 13 - Using the Grinder; Higher Speed Uses

Model H8125 9.6V Mini Grinder Kit -11 - 3. Insert at least 1 ⁄ 2 " of the bit into the collet. 4. Hand tighten the collet nut while depressing the collet lock. Then, use the collet wrench to tighten the collet nut an additional 1 ⁄ 3 turn. Failure to wear ANSI approved safety glasses while opera...

Page 14 - Installing the Flex Shaft

Model H8125 9.6V Mini Grinder Kit -12 - 5. Slide the outer flex shaft up the inner spindle and thread it firmly onto the grinder. 6. Loosen the collet nut on the working end of the flex shaft. 7. Insert a least 1 ⁄ 2 " of the desired bit into the collet of the flex shaft. Note: The flex shaft ca...

Page 15 - SECTION 5: MAINTENANCE; Changing LED Light Attachment

Model H8125 9.6V Mini Grinder Kit -13 - Daily Maintenance These procedures should be done after each use: • Wipe the motor housing, flex shaft, and tool bits with a dry cloth, or blow off the dust and debris with compressed air. • Check for damage to bits, cords, hous-ing, or other accessories. Lubr...

Page 16 - Parts Breakdown

Model H8125 9.6V Mini Grinder Kit -14 - Parts Breakdown � � � � � � � � � �� REF PART # DESCRIPTION 1 PH8125001 PLASTIC CARRYING CASE 2 PHTEK1 TAP SCREW #6 X 1/2 3 PH8125003 BOTTOM COVER 4 PH8125004 MOTOR/SWITCH/SPINDLE ASSY 5 PH8125005 TOP COVER 6 PH8125006 SPIND...

Page 17 - WARRANTY AND RETURNS

Model H8125 9.6V Mini Grinder Kit -15 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterati...

Page 19 - WARRANTY CARD

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

Page 20 - Send a Grizzly Catalog to a friend:; Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here

Grizzly Industrial H8125 - Manual

Table of Contents:

Summary

Other Grizzly Industrial Models