Page 2 - Table of Contents
Table of Contents INTRODUCTION ...............................................................................................................1 Foreword .....................................................................................................................1Machine Data ...................
Page 3 - INTRODUCTION; Foreword
Model H7826 Flooring Nailer -1 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any service...
Page 4 - NOTICE
Model H7826 Flooring Nailer -2 - Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN ...
Page 5 - Safety Instructions For Pneumatic Tools
Model H7826 Flooring Nailer -3 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck-ties, rings, bracelets, or other jew-elry which may get caug...
Page 6 - Additional Safety Instructions for Nailers
Model H7826 Flooring Nailer -4 - 1. HAND AND FOOT INJURIES: Do not place your hands or feet near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or foot. 2. COMPRESSED AIR RATING: Do not connect the nailer to compressed air that exceeds...
Page 8 - Unpacking; Inventory
Model H7826 Flooring Nailer -6 - SECTION 2: SETUP Figure 1. Model H7826 inventory. Unpacking Your Model H7826 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice....
Page 9 - Compressed Air
Model H7826 Flooring Nailer -7 - Compressed Air System The Model H7826 is designed to be oper-ated at 70-110 PSI using clean, dry, regu-lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres-sure for your model. Before using, regu- late the air pressure on your air compres-sor to 70...
Page 10 - Firing Mechanism
Model H7826 Flooring Nailer -8 - Firing Mechanism NOTICE Continually firing the nailer when empty will cause internal damage. Only fire the empty nailer once or twice to ensure it is functioning properly. The nailer should not fire when connected to the air supply unless it is fired by hitting the &...
Page 11 - SECTION 3: OPERATIONS; Oiling Nailer; Loading Nailer
Model H7826 Flooring Nailer -9 - SECTION 3: OPERATIONS Oiling Nailer Pneumatic oil has been included with this Grizzly nailer to help maintain its useful life. Place several drops of oil in the nailer air inlet (as shown in Figure 3 ) before every use and several times a day if used continuously. Wi...
Page 12 - Operating Nailer
Model H7826 Flooring Nailer -10 - Operating Nailer Figure 5. Operating nailer. Read the safety instructions in this manual before operating the nailer. Before you operate your nailer, place sev-eral drops of the included oil into the quick connect fitting where the nailer connects to the air supply....
Page 13 - Clearing Jammed
Model H7826 Flooring Nailer -11 - This nailer may accidentally fire if you work on it without disconnecting it from the air supply. Always discon-nect air from nailer whenever clearing a jammed nail! A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis-cha...
Page 14 - SECTION 4: MAINTENANCE; Cleaning; Rings
Model H7826 Flooring Nailer -12 - SECTION 4: MAINTENANCE Cleaning DISCONNECT THE AIR SUPPLY! Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the ...
Page 16 - Troubleshooting; Symptom
Model H7826 Flooring Nailer -14 - Troubleshooting Symptom Possible Cause Solution Air leaking at whack cap area. 1. Damaged seal.2. O-rings on the plunger are damaged. 1. Replace damaged seal.2. O-rings must be replaced. Air leaking between body and hose. 1. Loose air fitting. 1. Tighten air fitting...
Page 17 - Parts
Model H7826 Flooring Nailer -15 - Parts ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ������ ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �...
Page 18 - WARRANTY AND RETURNS
Model H7826 Flooring Nailer -16 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or...
Page 19 - WARRANTY CARD
WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...
Page 20 - Send a Grizzly Catalog to a friend:; Place
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here
