Page 3 - Table of Contents
Table of Contents INTRODUCTION ...............................................................................................................2 Foreword .....................................................................................................................2Contact Information ............
Page 4 - INTRODUCTION; Foreword
Model H7790/H7791 Laminate Trim Router -2 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have ...
Page 5 - Laminate Trim Router; RPM
Model H7790/H7791 Laminate Trim Router -3 - Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Laminate Trim Router Models H7790 and H7791 MODEL H7790 H7791 HP 5 ⁄ 8 1 ⁄ 2 NO LOAD SPEED 30,000 RPM 30,000 RPM COLLET SIZE 1 ⁄ 4 " 1 ⁄ 4 ...
Page 6 - Identification
Model H7790/H7791 Laminate Trim Router -4 - Identification A. ON/ OFF Switch B. Collet C. Base Plate D. Height Adjustment Lock Knob E. Height Adjustment Knob F. Curved Trim Guide G. Straight Trim Guide H. Depth Scale Figure 1. Router component identification. A B C D E F H Model H7791 Model H7790 A ...
Page 7 - NOTICE
Model H7790/H7791 Laminate Trim Router -5 - For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard-ous conditions. This manual uses a series of symbols and signal words which are intended to convey the...
Page 9 - Additional Safety Instructions
Model H7790/H7791 Laminate Trim Router -7 - 1. READ THE ENTIRE MANUAL: This manual contains proper operating instructions for this router. 2. SAFETY EQUIPMENT: Wear safety glasses, respirator, and hearing pro-tection when operating a router. 3. POWER SOURCE : Unplug the router and make sure the swit...
Page 10 - Extension Cords; Electrical Safety
Model H7790/H7791 Laminate Trim Router -8 - This tool must have a ground prong in the plug to help ensure that it is grounded. DO NOT remove ground prong from plug to fit into a two-pronged outlet! If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. Exte...
Page 11 - SECTION 2: OPERATIONS; Removing /Installing
Model H7790/H7791 Laminate Trim Router -9 - SECTION 2: OPERATIONS Removing /Installing Router Bit This router is supplied with a 1 ⁄ 4 " collet for use with 1 ⁄ 4 " shank router bits. It will accept router bits up to a 1 1 ⁄ 8 " diameter. Carefully inspect router bits for cracks, chips, ...
Page 12 - Adjusting Bit Depth; Feed Direction
Model H7790/H7791 Laminate Trim Router -10 - Adjusting Bit Depth To adjust the bit depth: 1. UNPLUG THE ROUTER AND MAKE SURE THE SWITCH IS OFF ! 2. Loosen the lock knob shown in Figure 4 and adjust the base to approximately the desired height. Unplug the router and make sure the switch is OFF before...
Page 13 - Routing Operations
Model H7790/H7791 Laminate Trim Router -11 - • Performing routing operations in mul-tiple passes produces smoother results with less chance of “chip out” and burn-ing of the workpiece. It also reduces the possibility of the router jerking out of your hands from trying to remove too much material in ...
Page 14 - Straight Guide; Curved Trim Guide
Model H7790/H7791 Laminate Trim Router -12 - Straight Guide The straight guide can be used for trim-ming, cutting dadoes, straight dovetails, and for cutting circles. Only use router bits with no guide bearing when using the straight guide. To use the straight guide tor trimming: 1. Slide the straig...
Page 16 - Template Guide
Model H7790/H7791 Laminate Trim Router -14 - Template Guide The template guide allows the router to follow a template or pattern. This setup is necessary when routing interior slots where a bit with a guide bearing will not fit. To install the template guide: 1. Remove the screws securing the bot-to...
Page 17 - SECTION 3: ACCESSORIES
Model H7790/H7791 Laminate Trim Router -15 - SECTION 3: ACCESSORIES Figure 14. Our most popular safety glasses. G7984—Face ShieldH1298—Dust Sealed Safety GlassesH1300—UV Blocking, Clear Safety GlassesH2347—Uvex ® Spitfire Safety Glasses H0736—Shop Fox ® Safety Glasses Safety Glasses are essential to...
Page 19 - SECTION 4: MAINTENANCE; Router Maintenance; Replacing Brushes
Model H7790/H7791 Laminate Trim Router -17 - Always disconnect power to the machine b efore p er forming maintenance. Failure to do this may result in serious personal injury. SECTION 4: MAINTENANCE Router Maintenance Motor brushes will become loaded with carbon deposits or wear out over time. Exten...
Page 22 - WARRANTY AND RETURNS
Model H7790/H7791 Laminate Trim Router -20 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alt...
Page 23 - WARRANTY CARD
WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...
Page 24 - Send a Grizzly Catalog to a friend:; Place
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here
