Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................................................................................................... 4 Foreword .....................................................................................................................................
Page 4 - Foreword; INTRODUCTION; Contact Info
-2- G9969 Radial Drill Press If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or parts reques...
Page 5 - Identification
G9969 Radial Drill Press -3- Figure 1. G9969 Identification. Identification A. Main Power and Light Switches B. Downfeed Handles C. Belt Cover Knob D. Belt Tension Lever E. Belt Tension Lock Knob F. Pinion Hub G. Headstock Lock Handles H. Headstock Tilt Scale I. Crank Handle J. Junction Box K. Depth...
Page 6 - MACHINE DATA; Machine Data Sheet
-4- G9969 Radial Drill Press The information contained herein is deemed accurate as of 5/12/2006 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G9969 MACHINE DAT...
Page 10 - Safety for Drill Presses
-8- G9969 Radial Drill Press 1. EYE/FACE/HAND PROTECTION. A face shield or safety glasses is recommended. Always keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO NOT wear gloves when operating the drill. 2. SECURING BIT. Properly tighten and securely ...
Page 11 - SECTION 2: CIRCUIT REQUIREMENTS
G9969 Radial Drill Press -9- Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. 110/220V Operation SECTION 2: CIRCUIT REQUIREMENTS Amperage Draw T...
Page 12 - Extension Cords
-10- G9969 Radial Drill Press In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connect-ed to the grounding prong on the plug; likewise, the outlet must be properly installed and ground-ed. All electrical connecti...
Page 13 - Set Up Safety; Unpacking
G9969 Radial Drill Press -11- Wear safety glasses dur- ing the entire set up pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Set Up Safety SECTION 3: SET U...
Page 14 - Inventory; NOTICE; Clean Up
-12- G9969 Radial Drill Press Inventory After all the parts have been removed from the crate, you should have the following items: Box 1: (Figure 3) Qty A. Drill Press Headstock ................................. 1 B. Headstock Bracket ..................................... 1 C. Column Cap (attached t...
Page 15 - Hardware Recognition Chart
G9969 Radial Drill Press -13- Hardware Recognition Chart
Page 16 - Site Considerations
-14- G9969 Radial Drill Press Figure 4. Minimum working clearances. Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some floors may require additional reinforcement to support the machine, workpiece, and opera-tor. Working Clearances Consider e...
Page 18 - Headstock
-16- G9969 Radial Drill Press Figure 9. Headstock bracket lock handles. Components and Hardware Needed: Qty Base/Column/Bracket Assembly ....................... 1Headstock ......................................................... 1 To install the headstock: 1. With the help of an assistant, lift the...
Page 19 - Belt Cover Knob
G9969 Radial Drill Press -17- Components and Hardware Needed: Qty Downfeed Handles ............................................ 3Cover Knob 1 ⁄ 4 "-20 ............................................. 1 Phillips Head Screw 1 ⁄ 4 "-20 x 1 ⁄ 2 " ........................ 1 Flat Washer 1 ⁄ 4 ...
Page 21 - Test Run
G9969 Radial Drill Press -19- Test Run Once the assembly is complete, test run your machine to make sure it runs properly, and to test prominent safety features installed on the machine. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the mac...
Page 22 - Operation Safety; SECTION 4: OPERATIONS; Safety Switch Key
-20- G9969 Radial Drill Press Loose hair and cloth- ing could get caught in machinery and cause seri- ous personal injury. Keep loose clothing and long hair away from moving machinery. Operation Safety SECTION 4: OPERATIONS NOTICE If you have never used this type of machine or equipment before, WE S...
Page 23 - Arbor Removal
G9969 Radial Drill Press -21- The arbor can be removed to install other Morse taper tooling in the spindle. A drift key is included to help remove the arbor or other tooling from the spindle. Usually, once the chuck and arbor have been properly mounted together, they are considered semi-permanent co...
Page 24 - Basic Drilling
-22- G9969 Radial Drill Press The Model G9969 is designed for drilling holes in wood, plastics or metal. The basic operation of a drill press is lining up your drill bit with the intended hole location, turning the drill press ON , and using the downfeed handles to move the spinning drill bit into t...
Page 25 - Choosing Speeds
G9969 Radial Drill Press -23- Choosing Speeds Twist/Brad Point Drill Bits Soft W ood Hard Wood Plastic Brass Aluminum Mild Steel 1/16" – 3/16" 3000 2500 2500 2500 3000 2500 13/64" – 3/8" 2000 1500 2000 1250 2500 1250 25/64" – 5/8" 1500 750 1500 750 1500 600 11/16" – 1"...
Page 26 - Changing Speeds
-24- G9969 Radial Drill Press 4. Locate the desired speed on the speed chart under the belt cover and move the V-belts to the desired V-grooves on the motor, idler, and spindle pulleys. For Example: As indicated in the speed chart ( Figure 22 ), a belt combination of A-2 creates 540 RPM. Note: Both ...
Page 27 - Depth Stop
G9969 Radial Drill Press -25- Depth Stop Figure 23. Depth stop components. Calibration Nut Depth Stop Bracket Depth Nut Jam Nut Return Height Nut The Model G9969 has a depth stop that allows you to drill repeated non-through holes to the same depth every time. The depth stop consists of a stud attac...
Page 29 - SECTION 5: ACCESSORIES
G9969 Radial Drill Press -27- SECTION 5: ACCESSORIES G2500—20-Piece Regular Sanding Drum Set Use on your drill press, lathe, or hand drill. This kit consists of 5 drums in popular 1 ⁄ 2 " x 1 ⁄ 2 ", 3 ⁄ 4 " x 1", 1"x 1", 1 1 ⁄ 2 " x 1 1 ⁄ 2 ", and 2" x 1 1 ⁄ 2 ...
Page 30 - SECTION 6: MAINTENANCE; Unpainted Cast Iron
-28- G9969 Radial Drill Press Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. SECTION 6: MAINTENANCE Protect the unpainted cast iron surfaces by wip-ing them clean after every use—this ensures moisture from wood dust d...
Page 31 - About Service; Troubleshooting
G9969 Radial Drill Press -29- Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. SECTION 7: SERVICE About Service S...
Page 35 - Electrical Components
G9969 Radial Drill Press -33- Electrical Components Figure 32. G9969 Switch Wiring. Figure 33. G9969 Junction Box Wiring.
Page 36 - Wiring Diagram
-34- G9969 Radial Drill Press ������ ������� ������ �� �� ����� ��������� ������� ������ �� �� �� �� �� �� �� � � � � � � �� �� ������ ������� ������ �� �� ����� ��������� ������� ������ �� �� �� �� �� ��� ��� ������ ��������� ������������� ��������� ���������������� ��� ��� � �� �� �� �� �� �� ����...
Page 37 - Parts Breakdown
G9969 Radial Drill Press -35- ��� �� ����� ����� ����� �� ����� �� �� �� �� �� �� ��� ��� ��� �� � ��� � �� �� �� �� �� �� ���� �� �� �� �� �� ���� �� �� �� �� �� �� ���� �� �� �� � � � �� ���� ���� �� �� � �� ��� �� �� �� �� �� �� �� �� �� �� �� �� �� ��� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �...
Page 38 - Parts List
-36- G9969 Radial Drill Press REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P9969001 BASE 49 P9969049 CORD CLAMP 2 PB32M HEX BOLT M10-1.5 x 25 50 P9969050 BODY 3 P9969003 RACK 51 PB03M HEX BOLT M8-1.25 X 16 4 P9969004 COLUMN 52 P9969052 SHIFTER 5 P9969005 GEARBOX BRACKET 53 P9969053 SLIDE BAR 6 P9...
Page 39 - Parts List and Label Placement
G9969 Radial Drill Press -37- REF PART # DESCRIPTION REF PART # DESCRIPTION 94 P9969094 LIGHT BASE 110V 105 P9969105 WARNING/ID LABEL 94A PS06M PHLP HD SCR M5-.8 x 20 106 P9969106 SPEED CHART LABEL 95 P9969095 LIGHT SCREW 107 P7943107 GRIZZLY BLACK/AL LABEL 96 P9969096 SWITCH PLATE 108 P7943108 BELT...
Page 40 - WARRANTY AND RETURNS
-38- G9969 Radial Drill Press Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lac...
