Grizzly Industrial G8220 Manual

Page 3 - Table Of Contents

G8220 Wet/Dry Bench Grinder -1- Table Of Contents PAGE 1. SAFETY SAFETY INSTRUCTIONS FOR POWER TOOLS ................................................2-3ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ............................

Page 5 - Safety Instructions For Power Tools

G8220 Wet/Dry Bench Grinder -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi-tion. Conductor size should be in accor-dance with the chart below. The amperagerating should be listed on the motor or toolnameplate. An undersized cord will cause adrop in line voltage res...

Page 6 - Additional Safety Instructions For Grinders

-4- G8220 Wet/Dry Bench Grinder Additional Safety Instructions For Grinders 1. Wear a face shield and/or safety gog-gles. 2. Use clamps and supports to sharpentools. 3. Grinding creates sparks. Make sureyour work area is free of combustiblematerials. 4. Dress the grinding wheel when its sur-face bec...

Page 7 - SECTION 2: CIRCUIT REQUIREMENTS; Fusing

G8220 Wet/Dry Bench Grinder -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15-amp fuse or circuit breaker should be usedwhen connecting this Bench Grinder. Circuitsrated any higher are not adequate to protect themotor from power surges. Equipment returned to us for service that showsevidence o...

Page 8 - SECTION 3: INTRODUCTION; Commentary

-6- G8220 Wet/Dry Bench Grinder SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G8220Wet/Dry Bench Grinder. The Model G8220 is partof a growing Grizzly family of fine woodworkingmachinery. When used according to the guide-lines set forth in this manual, you can expectyears of trouble...

Page 9 - Unpacking; NOTICE

G8220 Wet/Dry Bench Grinder -7- Unpacking This Wet/Dry Bench Grinder is shipped from themanufacturer in a carefully packed carton. If youdiscover the machine is damaged after you’vesigned for delivery, and the truck and driver aregone, you will need to file a freight claim with thecarrier. Save the ...

Page 10 - Site Considerations; BENCH MOUNTING

-8- G8220 Wet/Dry Bench Grinder Site Considerations Notes BENCH MOUNTING Your G8220 Wet/Dry Grinder is designed to beused on a workbench. Make sure it is positionedat a comfortable working height. The machinecan be permanently mounted to a bench byremoving the base and using the four holes in themot...

Page 11 - Water Reservoir

G8220 Wet/Dry Bench Grinder -9- SECTION 4: ASSEMBLY Tool Rest/Eye Shield To assemble the Eye Shield: 1 . Take the L-shaped bracket and position it so the holes line up and the bracket is onthe underside of the plastic shield. 2. Use the two (2) combination head screws,washers and nuts to secure the ...

Page 13 - SECTION 5: Operations; Overview

G8220 Wet/Dry Bench Grinder -11- SECTION 5: Operations The dry wheel supplied with the G8220 is an 80grit Aluminum Oxide wheel good for heavy mate-rial removal and for roughing in to approximatedimensions. The wet wheel is a very fine 1000grit which, along with the water supply, allowsfine grinding ...

Page 14 - Dry Wheel Grinding

-12- G8220 Wet/Dry Bench Grinder Long straight types of blades such as jointer orplaner knives can also be sharpened on thismachine as well. Position the blades as shown in Figure 7, with the miter gauge set at a zero angle. For this type of operation, it is necessaryto sweep the blade edge across t...

Page 15 - SECTION 6: MAINTENANCE; Wheel Removal

G8220 Wet/Dry Bench Grinder -13- SECTION 6: MAINTENANCE After prolonged use, you may find it necessary toreplace the grinding wheel. New wheels for theModel G8220 are available through the Grizzlycatalog. Check the latest catalog for ordering andprice information. Changing the wet wheel: 1. Remove t...

Page 17 - GRIZZLY MODEL G8220 WET/DRY BENCH GRINDER; MACHINE DATA

G8220 Wet/Dry Bench Grinder -15- Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G8220 WET/DRY BENCH GRINDER MACHINE DATA SHEET Design Type .................................................................................................... Be...

Page 21 - WARRANTY CARD

10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt S...

Page 23 - WARRANTY AND RETURNS

To take advantage of this warranty, contact us bymail or phone and give us all the details. We willthen issue you a “Return Number’’, which mustbe clearly posted on the outside as well as theinside of the carton. We will not accept any itemback without this number. Proof of purchase mustaccompany th...